1、BSI Standards Publication PD ISO/TS 13399-307:2016 Cutting tool data representation and exchange Part 307: Creation and exchange of 3D models End mills for indexable insertsPD ISO/TS 13399-307:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-
2、307:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the nece
3、ssary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 89399 5 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Pu
4、blished Document was published under the authority of the Standards Policy and Strategy Committee on 29 February 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-307:2016 ISO 2016 Cutting tool data representation and exchange Part 307: Creation and exchange of 3D models En
5、d mills for indexable inserts Reprsentation et change des donnes relatives aux outils coupants Partie 307: Cration et change des modles 3D Fraises plaquettes amovibles TECHNICAL SPECIFICATION ISO/TS 13399-307 Reference number ISO/TS 13399-307:2016(E) First edition 2016-02-15PD ISO/TS 13399-307:2016I
6、SO/TS 13399-307:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including
7、 photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel.
8、+41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgPD ISO/TS 13399-307:2016ISO/TS 13399-307:2016(E)Foreword vi Introduction viii 1 Scope . 1 2 Normative references 1 3 Starting elements, coordinate systems, planes 2 3.1 General . 2 3.2 Reference system 2 3.3 Coordinate system at the c
9、utting part 3 3.4 Planes 4 3.5 Design of the pocket seat and cutting reference point (CRP) of the insert . 5 3.6 Adjustment coordinate system on workpiece side 8 3.6.1 General 8 3.6.2 Designation of the coordinate system workpiece side . 8 4 Design of the model . 9 4.1 General . 9 4.2 Necessary para
10、meters for the connection interface feature . 9 4.3 Necessary properties for inserts 10 4.3.1 General.10 4.3.2 Properties for equilateral, equiangular and equilateral, non- equiangular inserts .10 4.3.3 Properties for non-equilateral, equiangular and non-equilateral, non- equiangular inserts .11 4.3
11、.4 Design of the pocket seat feature11 5 End mill, non-centre cutting, single row .11 5.1 General 11 5.2 Necessary properties 12 5.3 Basic geometry .13 5.4 Determination of the position of the mounting coordinate system of insert 13 5.5 Chip flute and pocket seat 14 5.6 Assembly of a single row, non
12、-centre cutting end mill 15 6 Single row, non-centre cutting V-groove end mill 16 6.1 General 16 6.2 Necessary properties 17 6.3 Basic geometry .17 6.4 Determination of the position of the mounting coordinate system of insert 17 6.5 Chip flute and pocket seat 18 6.6 Single row, non-centre cutting V-
13、groove end mill assembly .19 7 Single row, non-centre-cutting dovetail end mill .20 7.1 General 20 7.2 Necessary properties 20 7.3 Basic geometry .21 7.4 Determination of the position of the mounting coordinate system of insert 21 7.5 Chip flute and pocket seat 21 7.6 Single row, non-centre-cutting
14、dovetail end mill assembly 22 8 T-slot end mill .22 8.1 General 22 8.2 Necessary properties 23 8.3 Basic geometry .23 8.4 Determination of the position of the mounting coordinate system of insert 23 8.5 Chip flute and pocket seat 24 8.6 Assembly of a T-slot end mill .25 ISO 2016 All rights reserved
15、iii Contents PagePD ISO/TS 13399-307:2016ISO/TS 13399-307:2016(E)9 Single row, rounded end mill 26 9.1 General 26 9.2 Necessary properties 27 9.3 Basic geometry .27 9.4 Determination of the position of the mounting coordinate system of insert 28 9.5 Chip flute and pocket seat 28 9.6 Assembly of a ro
16、unded end mill 30 10 Threading end mill 30 10.1 General 30 10.2 Necessary properties 31 10.3 Basic geometry .32 10.4 Determination of the position of the mounting coordinate system of insert 32 10.5 Chip flute and pocket seat 33 10.6 Assembled threading end mill 34 11 End mill, non-centre-cutting, m
17、ultiple rows.35 11.1 General 35 11.2 Necessary properties 35 11.3 Basic geometry .36 11.4 Determination of the position of the mounting coordinate system of insert 36 11.5 Chip flute and pocket seat 38 11.6 Multiple rows, non-centre-cutting end mill assembly .39 12 Angular end mill, non-centre-cutti
18、ng, multiple rows 40 12.1 General 40 12.2 Necessary properties 40 12.3 Basic geometry .41 12.4 Determination of the position of the mounting coordinate system of insert 41 12.5 Chip flute and pocket seat 41 12.6 Multiple rows non-centre-cutting angular end mill assembly 42 13 End mill, centre-cuttin
19、g, multiple rows .42 13.1 General 42 13.2 Necessary properties 43 13.3 Basic geometry .43 13.4 Determination of the position of the mounting coordinate system of insert 43 13.5 Chip flute and pocket seat 44 13.6 Multiple rows, centre-cutting angular end mill assembly 45 14 Spot-facing end mill 46 14
20、.1 General 46 14.2 Necessary properties 46 14.3 Basic geometry .47 14.4 Determination of the position of the mounting coordinate system of insert 47 14.5 Chip flute and pocket seat 47 14.6 Assembled spot-facing end mill 49 15 Straight ball-nosed end mill 49 15.1 General 49 15.2 Necessary properties
21、50 15.3 Basic geometry .50 15.4 Determination of the position of the mounting coordinate system of insert 51 15.5 Chip flute and pocket seat 52 15.6 Straight ball-nosed end mill assembly .53 16 Angular ball-nosed end mill 53 16.1 General 53 16.2 Necessary properties 54 16.3 Basic geometry .54 16.4 D
22、etermination of the position of the mounting coordinate system of insert 54 16.5 Chip flute and pocket seat 54 iv ISO 2016 All rights reservedPD ISO/TS 13399-307:2016ISO/TS 13399-307:2016(E)16.6 Angular ball-nosed end mill assembly 54 17 Die and mould end mill 54 17.1 General 54 17.2 Necessary prope
23、rties 55 17.3 Basic geometry .56 17.4 Determination of the position of the mounting coordinate system of insert 56 17.5 Chip flute and pocket seat 56 17.6 Die end mill assembly 58 18 Bell-style end mill .58 18.1 General 58 18.2 Necessary properties 59 18.3 Basic geometry .60 18.4 Determination of th
24、e position of the mounting coordinate system of insert 60 18.5 Chip flute and pocket seat 61 18.6 Bell-style end mill assembly .61 19 Design of details .61 19.1 Basis for modelling .61 19.2 Fixing threads for inserts 62 19.3 Contact/clamping surfaces Orientation 62 19.4 Chamfers and roundings .62 20
25、 Attributes of surfaces Visualization of the model features 62 21 Structure of the design elements (tree of model) .62 22 Data exchange model 63 Annex A (informative) Information about nominal dimensions 65 Bibliography .66 ISO 2016 All rights reserved vPD ISO/TS 13399-307:2016ISO/TS 13399-307:2016(
26、E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which
27、a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matt
28、ers of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This do
29、cument was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all
30、 such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and
31、 does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary inf
32、ormation. The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary fo
33、r the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference
34、systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 80: Creation and exchange of 3D models Overview and principles Technical Specification Part 100: Definitions, principles and methods for reference dictionaries Techni
35、cal Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: Creation and exchange of 3D models Replaceable in
36、serts for drilling Technical Specification Part 204: Creation and exchange of 3D models Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of thread cutting taps, thread forming taps and thread cutting d
37、ies Technical Specificationvi ISO 2016 All rights reservedPD ISO/TS 13399-307:2016ISO/TS 13399-307:2016(E) Part 302: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of solid drills and countersinking tools Technical Specification Part 303: Concept for th
38、e design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills with solid cutting edges Technical Specification Part 304: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of milling cutters with arbor hole and solid cutting e
39、dges Technical Specification Part 307: Creation and exchange of 3D models End mills for indexable inserts Technical Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Technical Specification Part 309: Creation and exchange of 3D models To
40、ol holders for indexable inserts Technical Specification Part 311: Creation and exchange of 3D models Solid reamers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexable inserts Technical Specification Part 401: Creation and exchange of 3D models Converting, exte
41、nding and reducing adaptive items Technical Specification Part 405: Creation and exchange of 3D models Collets Technical Specification The following parts are under preparation: Part 70: Graphical data layout Layer settings for tool designs Technical Specification Part 71: Graphical data layout Crea
42、tion of documents for the standardized data exchange Graphical product information Technical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML data exchange Technical Specification Part 305: Creation and exchange
43、 of 3D models Modular tooling systems with adjustable cartridges for boring Technical Specification Part 310: Creation and exchange of 3D models T urning tools with carbide tips Technical Specification ISO 2016 All rights reserved viiPD ISO/TS 13399-307:2016ISO/TS 13399-307:2016(E) Introduction This
44、 part of ISO/TS 13399 defines the concept, the terms and the definitions on how to design simplified 3D models of end mills for indexable inserts that can be used for NC-programming, simulation of the manufacturing processes and the determination of collision within machining processes. It is not in
45、tended to standardize the design of the cutting tool itself. A cutting tool is used in a machine to remove material from a workpiece by a shearing action at the cutting edges of the tool. Cutting tool data that can be described by ISO/TS 13399 (all parts) include, but are not limited to, everything
46、between the workpiece and the machine tool. Information about inserts, solid tools, assembled tools, adaptors, components and their relationships can be represented by ISO/ TS 13399 (all parts) . The increasing demand providing the end-user with 3D models for the purposes defined above is the basis
47、for the development of this series of International Standards. The objective of ISO/TS 13399 (all parts) is to provide the means to represent the information that describes cutting tools in a computer sensible form that is independent from any particular computer system. The representation will faci
48、litate the processing and exchange of cutting tool data within and between different software systems and computer platforms and support the application of this data in manufacturing planning, cutting operations and the supply of tools. The nature of this description makes it suitable not only for n
49、eutral file exchange, but also as a basis for implementing and sharing product databases and for archiving. The methods that are used for these representations are those developed by ISO/TC 184/SC 4 for the representation of product data by using standardized information models and reference dictionaries. Definitions and identifications of dictionary entries are defined by mean
