1、BSI Standards Publication PD ISO/TS 13399-405:2016 Cutting tool data representation and exchange Part 405: Creation and exchange of 3D models ColletsPD ISO/TS 13399-405:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-405:2016. The UK partici
2、pation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a co
3、ntract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 84148 4 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was pub
4、lished under the authority of the Standards Policy and Strategy Committee on 31 March 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-405:2016 ISO 2016 Cutting tool data representation and exchange Part 405: Creation and exchange of 3D models Collets Reprsentation et chan
5、ge des donnes relatives aux outils coupants Partie 405: Cration et change de modles 3D Pinces de serrage TECHNICAL SPECIFICATION ISO/TS 13399-405 Reference number ISO/TS 13399-405:2016(E) First edition 2016-03-01PD ISO/TS 13399-405:2016ISO/TS 13399-405:2016(E)ii ISO 2016 All rights reserved COPYRIGH
6、T PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, witho
7、ut prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.
8、orgPD ISO/TS 13399-405:2016ISO/TS 13399-405:2016(E)Foreword v Introduction vii 1 Scope . 1 2 Normative references 1 3 Starting elements, coordinate systems, planes 2 3.1 General . 2 3.2 Reference system (PCS primary coordinate system) 2 3.3 Mounting coordinate system 2 3.4 Adjustment coordinate syst
9、em at workpiece side . 3 3.4.1 General 3 3.4.2 Designation of coordinate systems at workpiece side 3 3.4.3 Arrangement of coordinate system workpiece side 4 3.5 Planes 5 4 Design of the model . 6 4.1 General . 6 4.2 Necessary properties for the connection interface feature 7 5 Double angle collet .
10、7 5.1 General . 7 5.2 Necessary properties . 8 5.3 Basic geometry 8 5.4 Double angle collet, complete 9 6 Collet with straight shoulder . 9 6.1 General . 9 6.2 Necessary properties 10 6.3 Basic geometry .10 6.4 Completed collet with straight shoulder .11 7 Short double angle collet 11 7.1 General 11
11、 7.2 Necessary properties 12 7.3 Basic geometry .12 7.4 Completed short double angle collet 13 8 Collet with elastic segments 13 8.1 General 13 8.2 Necessary properties 13 8.3 Basic geometry .14 8.4 Completed collet with elastic segments .14 9 Collet with axial adjustment 15 9.1 General 15 9.2 Neces
12、sary properties 15 9.3 Basic geometry .15 9.4 Completed collet with axial adjustment .16 10 Dr a w -in c ollet with r etaining thr ead and spanner flats .17 10.1 General 17 10.2 Necessary properties 17 10.3 Basic geometry .18 10.4 Completed draw-in collet with retaining thread and spanner flats .18
13、11 Draw in collet with retaining thread 19 11.1 General 19 11.2 Necessary properties 19 11.3 Basic geometry .19 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-405:2016ISO/TS 13399-405:2016(E)11.4 Completed draw-in collet with retaining thread 20 12 Cylindrical clamping sleeve 20 12.1
14、General 20 12.2 Necessary properties 20 12.3 Basic geometry .21 12.4 Completed cylindrical clamping sleeve 21 13 Conical clamping sleeve with retaining thread .22 13.1 General 22 13.2 Necessary properties 22 13.3 Basic geometry .23 13.4 Completed conical clamping sleeve with retaining thread 23 14 F
15、errule 24 14.1 General 24 14.2 Necessary properties 24 14.3 Basic model .24 14.4 Completed ferrule25 15 Dead length type collet .25 15.1 General 25 15.2 Necessary properties 25 15.3 Basic geometry .26 15.4 Completed dead length type collet .26 16 Design of details .27 16.1 Basics for modelling 27 16
16、.2 Contact surfaces, driving features Orientation .27 16.3 Chamfers and roundings .27 16.4 Attributes of surfaces Visualization of the model features.27 17 Structure of the design elements (tree of model) .28 18 Data exchange model 28 Annex A (informative) Information about nominal dimensions 30 Bib
17、liography .31 iv ISO 2016 All rights reservedPD ISO/TS 13399-405:2016ISO/TS 13399-405:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carrie
18、d out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS
19、O collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different
20、 approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be
21、 the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
22、 Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles
23、in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Ove
24、rview, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference diction
25、ary for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 80: Creation and exchange of 3D models Overview and principles Technical Sp
26、ecification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular
27、inserts Technical Specification Part 203: Creation and exchange of 3D models Replaceable inserts for drilling Technical Specification Part 204: Creation and exchange of 3D models Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models based on properties according t
28、o ISO/TS 133993: Modelling of thread cutting taps, thread forming taps and thread cutting dies Technical Specification ISO 2016 All rights reserved vPD ISO/TS 13399-405:2016ISO/TS 13399-405:2016(E) Part 302: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modellin
29、g of solid drills and countersinking tools Technical Specification Part 303: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills with solid cutting edges Technical Specification Part 304: Concept for the design of 3D models based on properties a
30、ccording to ISO/TS 133993: Modelling of milling cutters with arbor hole and solid cutting edges Technical Specification Part 307: Creation and exchange of 3D models End mills for indexable inserts Technical Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole fo
31、r indexable inserts Technical Specification Part 309: Creation and exchange of 3D models Tool holders for indexable inserts Technical Specification Part 311: Creation and exchange of 3D models Solid reamers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexable in
32、serts Technical Specification Part 401: Creation and exchange of 3D models Converting, extending and reducing adaptive items Technical Specification Part 405: Creation and exchange of 3D models Collets Technical Specification The following parts are under preparation: Part 70: Graphical data layout
33、Layer settings for tool designs Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing
34、 header and their XML data exchange Technical Specification Part 305: Creation and exchange of 3D models Modular tooling systems with adjustable cartridges for boring Technical Specification Part 310: Creation and exchange of 3D models T urning tools with carbide tips Technical Specificationvi ISO 2
35、016 All rights reservedPD ISO/TS 13399-405:2016ISO/TS 13399-405:2016(E) Introduction This part of ISO/TS 13399 defines the concept, the terms and the definitions on how to design simplified 3D models of collets, clamping sleeves, ferrules and expanding sleeves that can be used for NC-programming, si
36、mulation of the manufacturing processes and the determination of collision within machining processes. It is not intended to standardize the design of the cutting tool itself. A cutting tool is used in a machine to remove material from a workpiece by a shearing action at the cutting edges of the too
37、l. Cutting tool data that can be described by ISO/TS 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts, solid tools, assembled tools, adaptors, components and their relationships can be represented by ISO/TS 13399 (all
38、 parts). The increasing demand providing the end user with 3D models for the purposes defined above is the basis for the development of this series of International Standards. The objective of this International Standard is to provide the means to represent the information that describes cutting too
39、ls in a computer-sensible form that is independent from any particular computer system. The representation will facilitate the processing and exchange of cutting tool data within and between different software systems and computer platforms and support the application of this data in manufacturing p
40、lanning, cutting operations and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange, but also as a basis for implementing and sharing product databases and for archiving. The methods that are used for these representations are those developed by I
41、SO/TC 184/SC 4 for the representation of product data by using standardized information models and reference dictionaries. Definitions and identifications of dictionary entries are defined by means of standard data that consist of instances of the EXPRESS entity data types defined in the common dict
42、ionary schema, resulting from a joint effort between ISO/TC 184/SC 4 and IEC/TC 3/SC 3D and in its extensions defined in ISO 13584-24 and ISO 13584-25. ISO 2016 All rights reserved viiPD ISO/TS 13399-405:2016PD ISO/TS 13399-405:2016Cutting tool data representation and exchange Part 405: Creation and
43、 exchange of 3D models Collets 1 Scope This part of ISO/TS 13399 specifies a concept for the design of adaptive items, limited to any kind of collets, clamping sleeves and ferrules, together with the usage of the related properties and domains of values. This part of ISO/TS 13399 specifies a common
44、way of design simplified models that contain the following: definitions and identifications of the design features of collets, clamping sleeves, and ferrules, with an association to the used properties; definitions and identifications of the internal structure of the 3D model that represents the fea
45、tures and the properties of collets, clamping sleeves, and ferrules. The following are outside the scope of this part of ISO/TS 13399: applications where these standard data may be stored or referenced; concept of 3D models for cutting tools; concept of 3D models for cutting items; concept of 3D mod
46、els for tool items; concept of 3D models for other adaptive items not being described in the scope of this part of ISO 13399; concept of 3D models for assembly items and auxiliary items. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document
47、and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 296, Machine tools Self holding tapers for tool shanks ISO/TS 13399-3, Cutting tool data repr
48、esentation and exchange Part 3: Reference dictionary for tool items ISO/TS 13399-4, Cutting tool data representation and exchange Part 4: Reference dictionary for adaptive items ISO/TS 13399-50, Cutting tool data representation and exchange Part 50: Reference dictionary for reference systems and com
49、mon concepts ISO/TS 13399-60, Cutting tool data representation and exchange Part 60: Reference dictionary for connection systems ISO/TS 13399-80, Cutting tool data representation and exchange Part 80: Creation and exchange of 3D models Overview and principles TECHNICAL SPECIFICATION ISO/TS 13399-405:2016(E) ISO 2016 All rights reserved 1PD IS
