1、Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any datawhich may improve this document should be sent to: Defense Supply Center Richmond, ATTN:DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610.AMSC N/A FSC 6230DISTRIBUTION STATEMENT A . Approved f
2、or public release; distribution is unlimited.INCH-POUNDA-A-5920829 June 1998SUPERSEDINGMIL-L-11848C26 February 1976COMMERCIAL ITEM DESCRIPTIONLIGHTS, POWER TOOLThe General Services Administration has authorized the use of this commercialitem description for all federal agencies.1. SCOPE. This commer
3、cial item description (CID) covers various portable, adjustable, electric,power tool lights suitable for mounting on lathes or other stationary power tools for workpieceillumination.2. CLASSIFICATION. The power tool lights shall be of the following types, sizes, and styles. The type, size, and style
4、 to be furnished shall be as specified (see 7.2(b). Type is determined bythe type of mounting base and the design of the arm used to adjust the position of the lamp. Sizeis determined by the reach, which is the maximum length of extension from the mounting base tothe lamp housing. Style is determine
5、d by the type and wattage of the lamp(s) used. Table Ilists the minimum light output in lumens for various lamp types and wattages.Type 1A - Flexible (gooseneck) arm, clamp baseType 1B - Flexible (gooseneck) arm, magnetic baseType 2A - Articulated arm, clamp baseType 2B - Articulated arm, magnetic b
6、aseSize 01 - 12 to 15 inches Size 06 - 37 to 42 inchesSize 02 - 16 to 19 inches Size 07 - 43 to 48 inchesSize 03 - 20 to 24 inches Size 08 - 49 to 54 inchesSize 04 - 25 to 30 inches Size 09 - 55 to 60 inchesSize 05 - 31 to 36 inches Size 10 - 61 to 65 inchesProvided by IHSNot for ResaleNo reproducti
7、on or networking permitted without license from IHS-,-,-A-A-592082Style AA - 60 watt incandescent lamp Style CA - 25 watt h alogen lampStyle AB - 75 watt incandescent lamp Style CB - 60 watt halogen lampStyle AC - 100 watt incandescent lamp Style CC - 75 watt halogen lampStyle BA - 25 watt fluoresce
8、nt lamp Style CD - 100 watt halogen lampStyle BB - 60 watt fluorescent lampStyle BC - 75 watt fluorescent lampTABLE I. Minimum illumination output requirements, lumens.Lamp,watts Fluorescent Halogen Incandescent25 1000 600 -60 2000 900 60075 3000 1200 1000100 - 1400 14003. SALIENT CHARACTERISTICS3.1
9、 General requirements. The power tool lights shall meet the requirements of UnderwritersLaboratory (UL) 153. Unless otherwise specified (see 7.2(c), the power tool lights shall operatefrom a 120-volt, single-phase, 60-hertz circuit. The light may contain a built-in transformer forreducing the lamp o
10、perating voltage. When specified (see 7.2(d), the lamp housing and all of theelectrical items shall be waterproof. Unless otherwise specified (see 7.2(e), the power tool lightsshall be supplied with all lamps needed for normal operation of the lamp. The lamps shall bereplaceable and commercially ava
11、ilable.3.2 Components . The power tool lights shall include, as a minimum, the following components:3.2.1 Lamp housing . The lamp housing shall provide mechanical and electrical connections forone or more lamps of the style specified. The lamp housing shall provide a means of directing thelamp illum
12、ination toward the workpiece and away from the eyes of the tool operator.3.2.2 Power cord . The power tool lights shall be equipped with a three-conductor SJ-type cordmeeting the requirements of UL 62. The cord shall have a grounded plug that conforms to figure5-15 of National Electrical Manufacture
13、rs Association (NEMA) WD 6. Unless otherwisespecified (see 7.2(f), the cord shall extend a minimum of 6 feet beyond the mounting base. 3.2.3 Adjustable arm . The adjustable arm shall be horizontally and vertically adjustable and becapable of positioning and holding the lamp housing at the desired lo
14、cation and direction. Anypositioning positioning lockdown and friction adjustment devices shall be capable of beingoperated without the use of tools. The flexible (gooseneck) arm on type 1 power tool lights shallconsist of a single gooseneck tube of a constant diameter, which normally encloses the p
15、owercord. The articulated arm on type 2 power tool lights shall consist of two or more rigid armshinged together, which normally enclose the power cord except at its ends and hinges. Whenspecified (see 7.2(g), the adjustable arm shall completely enclose the power cord from themounting base to the la
16、mp housing.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5920833.2.4 Mounting base . The mounting base shall be metal and shall be designed for vertical andhorizontal mounting. The base of type 1A and 2A power tool lights shall be of the clamp
17、variety.The base of type 1B and 2B power tool lights shall be of the magnetic variety.3.2.5 Switch . The on-off switch shall be clearly visible and marked. The switch shall be locatedon the lamp housing, the base, or on the power cord within 3 feet of the base. When a waterprooflight is specified (s
18、ee 3.1, 7.2(d), the switch shall be waterproof. When specified for non-waterproof lights (see 7.2(h), the switch shall be covered with a moisture-resistant seal or rubberboot.3.2.6 Optional components . Optional components shall be furnished as specified (see 7.2(i).3.3 Performance . The light shall
19、 be capable of retaining a steady position at all desired adjustments, including fully contracted and fully extended, under conditions normally encounteredin machine tool operations. The light shall have an illumination output of not less than the numberof lumens shown in table I when equipped with
20、a lamp or lamps appropriate to its maximumwattage.4. REGULATORY REQUIREMENTS4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal AcquisitionRegulation (FAR).5. QUALITY ASSURANCE P
21、ROVISIONS5.1 Product conformance. The power tool lights shall meet the salient characteristics of thiscommercial item description; conform to the manufacturers own drawings, specifications,standards, and quality assurance practices; and be the same light offered for sale in the commercialmarket. The
22、 government reserves the right to require proof of such conformance.5.1.1 Verification of conformance . Suitable verification of conformance to UL 153 and UL 62shall be either the UL label on the product or certification of such conformance by an accreditedtesting laboratory satisfactory to the gove
23、rnment.5.2 Warranty . Unless otherwise specified (see 7.2(j), the manufacturers standard commercialwarranty, terms, and conditions shall apply.6. PACKAGING. Preservation, packing, and marking shall be as specified (see 7.2(k) in thecontract or purchase order.Provided by IHSNot for ResaleNo reproduct
24、ion or networking permitted without license from IHS-,-,-A-A-5920847. NOTES7.1 Sources of documents.7.1.1 Government documents . Copies of paragraph 23.403 of the FAR may be obtained fromthe Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.7.1.2 Nongovernment docume
25、nts . Copies of industry (voluntary) standards referenced in thisCID may be obtained from the following addresses:Underwriters Laboratories Inc. (UL)ANSI/UL 153 UL Standard for Safety Portable Electric LampsANSI/UL 62 UL Standard for Safety Flexible Cord and Fixture WireApplications for copies shoul
26、d be sent to: Underwriters Laboratories Inc., 333 Pfingsten Road,Northbrook, IL 60062.National Electrical Manufacturers Association (NEMA)ANSI/NEMA WD 6 Wiring Devices-Dimensional RequirementsApplications for copies should be sent to: National Electrical Manufacturers Association, 1300North 17th Str
27、eet, Suite 1847, Rosslyn, VA 22209.7.2 Ordering data . Acquisition documents must specify the following:a. Title, number, and date of this document.b. Type, size, and style of light required (see 2).c. Power source, if different (see 3.1).d. Waterproof, if required (see 3.1).e. Lamp(s) not included
28、(see 3.1).f. Power cord length, if different (see 3.2.2).g. Power cord completely enclosed, as specified (see 3.2.3).h. Moisture-resistant switch, if required (see 3.2.5).i. Optional components, if required (see 3.2.6).j. Warranty, if different (see 5.2).k. Packaging requirements, as specified (see
29、6).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5920857.3 Part identification number (PIN) . The following part identification numbering procedure isfor government purposes and does not constitute a requirement for the contractor.Example of PI
30、N for A-A-59208:A-A-59208 - 1A01AAStyle: AA through CD (See 2.)Size: 01 10 (See 2.)Type: 1A, 1B, 2A, 2B (See 2.) CID number7.4 Sources of supply . The following suppliers are known to offer products that conform to therequirements of this CID. This list is not indicative of all known suppliers:Amtos
31、 LightingDazorElectrix LightingFostoria IndustriesHalogen Lighting Products CorporationLuxo CorporationRoxter Manufacturing CorporationWaldmann LightingWilton Machinery ProductsMILITARY INTERESTS: PREPARING ACTIVITYDLA - GSCustodiansAir Force - 99 (Project 6230-1061)Navy - SH ReviewersAir Force - 82Air Force - 84Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
