STAS 2697-1951 《正常压力为25kgf cm2以及100kgf cm2的钢制管子接头 弯管、丁字管以及带套管的四通管大小》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

STAS 8097-1987 Assembly tools for screws and nuts SOCKET WRENCH OPENINGS AND OPEN-ENDED WRENCHES 《用于螺丝和螺母的装配工具 套筒扳头开口和可扩充扳手 》.pdf

STAS 8098-1968 《沥青 石蜡含量的测定》.pdf

STAS 8099-1974 BITUMENS Determination of loss in weight by heating《沥青 加热重量损失的测定 》.pdf

STAS 8100 1-1988 CIMITS AND FITS SYSTEM FOR LINEAR DIMENSIONS Terminology and symbols 《线性尺寸的限制与配合系统 术语和符号 》.pdf

STAS 8100 2-1988 LIMITS AND PITS SYSTEM FOR LINEAR DIMENSIONS Fundamental limits and fundamental fits for dimensions up to 3150 mm 《线性尺寸的限量及配合系统 尺寸高达3150毫米的基本限制和基本配合 》.pdf

STAS 8100 3-1988 LIMITS AND FITS SYSTEM FOR LINEAR DIMENSIONS General use tolerance classes for dimensions up to 3150 mm《线性尺寸的极限与配合系统 尺寸高达3150毫米的通用公差等级 》.pdf

STAS 8100 4-1988 LIMITS AND FITS SYSTEM FOR LINEAR DIMENSIONS General use tolerance classes selection for dimensions up to 500 mm《线性尺寸的极限与配合系统尺寸高达500毫米的通用公差等级选择 》.pdf

STAS 8100 5-1990 Limits and fits system for linear dimensions Fundamental limits fundamental fits and tolerance classes for dimensions over 3150 mm and up to 10000 mm《线性尺寸的极限与适合系统..pdf

STAS 8100 6-1990 Limits and fits shstem for linear dimensions Fundamental limits fundamental fits and tolerance classes for dimensions over 10000 mm and up to 40000 mm《线性尺寸的极限与适合系统.pdf