ABMA 10285-2009 Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances.pdf

上传人:李朗 文档编号:418461 上传时间:2018-11-06 格式:PDF 页数:20 大小:311.51KB
下载 相关 举报
ABMA 10285-2009 Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances.pdf_第1页
第1页 / 共20页
ABMA 10285-2009 Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances.pdf_第2页
第2页 / 共20页
ABMA 10285-2009 Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances.pdf_第3页
第3页 / 共20页
ABMA 10285-2009 Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances.pdf_第4页
第4页 / 共20页
ABMA 10285-2009 Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances.pdf_第5页
第5页 / 共20页
亲,该文档总共20页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、 Rolling bearings - Sleeve type linear ball bearings - Boundary dimensions and tolerances ANSI/ABMA/ISO 10285-2009 (R2015) Sponsor American Bearing Manufacturers Association ANSI/ABMA/ISO 10285-2009 Reaffirmed 2015 (Identical Adoption of ISO 10285:2007) Copyright American Bearing Manufacturers Assoc

2、iation, Inc. Neither part of the printed publication, nor any part of the electronic tile may be reproduced or transmitted in any form, including transmittal by e-mail, by file transfer protocol (FTP), or by being made part of a network-accessible system, without the prior written permission of the

3、copyright owner. ABMA FOREWORD (This foreword is not part of ANSI/ABMA/ISO 10285-2009.) IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of developing International Standards is carried out through IS0 techn

4、ical committees. Every member body interested in a subject for which a technical committee has been authorized has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. The text is approved as a

5、n International Standard if a two-thirds majority of the P (participating)-members of the TC/SC are in favor and not more than one-quarter of the total number of votes cast are negative. International Standard 10285:2007 was prepared by Technical Committee ISO/TC 4, Rolling Bearings. This standard w

6、as processed and approved for submittal to ANSI for national adoption by Accredited Standards Committee B3. Committee approval of the national adoption of this standard does not necessarily mean that all committee members voted for its adoption. Suggestions for the improvement of this standard gaine

7、d through experience with its use will be welcomed. These suggestions should be sent to: ASC B3 Secretariat American Bearing Manufacturers Association 2025 M Street, N.W., Suite 800 Washington, DC 20036 Reference numberISO 10285:2007(E)ISO 2007INTERNATIONAL STANDARD ISO10285Second edition2007-11-01R

8、olling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances Roulements Roulements linaires recirculation de billes, type manchon Dimensions dencombrement et tolrances ISO 10285:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes lice

9、nsing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The IS

10、O Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has be

11、en taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of

12、 this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH

13、-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reservedISO 10285:2007(E) ISO 2007 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and d

14、efinitions. 1 4 Symbols . 2 5 Boundary dimensions 3 6 Tolerances . 3 6.1 Classes 3 6.2 Applicability. 3 6.3 Shaft tolerances 3 Annex A (informative) Basis of tolerances for sleeve type linear ball bearings 10 Bibliography . 11 ISO 10285:2007(E) iv ISO 2007 All rights reservedForeword ISO (the Intern

15、ational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has b

16、een established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical sta

17、ndardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies f

18、or voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or a

19、ll such patent rights. ISO 10285 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 11, Linear motion rolling bearings. This second edition cancels and replaces the first edition (ISO 10285:1992), which has been technically revised. ISO 10285:2007(E) ISO 2007 All rights

20、reserved vIntroduction Linear motion rolling bearings provide for linear motion as opposed to rotational motion. The sleeve type linear ball bearing described in this International Standard uses balls which circulate in a number of closed loops in the cylindrical bearing that surrounds the shaft. Li

21、near ball bearings are typically applied to meet one or more of the following criteria: a) smooth low-friction motion, free from stick-slip or chatter; b) low force required to produce relative linear motion between the bearing and the shaft. These requirements, as well as others, can be met by appr

22、opriate use of the various linear motion rolling bearing types (closed sleeve type, adjustable sleeve type and open sleeve type). The appropriate selection of bearing type and specification is to be established between the manufacturer and the user. INTERNATIONAL STANDARD ISO 10285:2007(E) ISO 2007

23、All rights reserved 1Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances 1 Scope This International Standard specifies the boundary dimensions, tolerances and definitions for sleeve type linear motion ball bearings. It is applicable to the size ranges covered by Tabl

24、e 1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the reference document (including any amendments) applies. ISO 1132-1, Rolling be

25、arings Tolerances Part 1: Terms and definitions ISO 5593, Rolling bearings Vocabulary ISO 13012, Rolling bearings Linear motion, recirculating ball, sleeve type Accessories ISO 15241, Rolling bearings Symbols for quantities 3 Terms and definitions For the purposes of this document, the terms and def

26、initions given in ISO 1132-1, ISO 5593 and the following apply. 3.1 sleeve type linear ball bearing linear motion ball bearing incorporating an outer sleeve with a number of closed loops of recirculating balls, which is designed to achieve unlimited linear motion along a shaft 3.2 shaft basically cy

27、lindrical rod along which a linear ball bearing traverses 3.3 nominal bore diameter of ball complement diameter of the theoretical cylinder inscribed inside all of the balls 3.4 nominal outer sleeve width distance between two theoretical end faces designated to bound the width of the linear ball bea

28、ring ISO 10285:2007(E) 2 ISO 2007 All rights reserved3.5 radial runout difference between the largest and the smallest of the radial distances between the outside surface of the cylindrical outer sleeve and the centreline of the bore diameter of ball complement 3.6 closed sleeve type linear ball bea

29、ring sleeve type linear ball bearing in which the outer sleeve is continuous or virtually continuous, whereby adjustment of clearance between the bore diameter of ball complement and a shaft is achieved, in most cases, by selection of the housing fit, a shaft diameter and the bore diameter of ball c

30、omplement of the bearing 3.7 adjustable sleeve type linear ball bearing sleeve type linear ball bearing which has elastic features which permit mechanical adjustment of the clearance between the bore diameter of ball complement and a shaft 3.8 open sleeve type linear ball bearing sleeve type linear

31、ball bearing in which a longitudinal section is removed to provide clearance over a shaft and shaft support rail unit 4 Symbols For the purposes of this International Standard, the symbols given in ISO 15241 and the following apply. The symbols (except those for tolerances) shown in Figures 1 and 2

32、and the values given in Tables 1 to 9 denote nominal dimensions, unless specified otherwise. b snap ring groove width C outer sleeve width Cssingle outer sleeve width C1distance between outer faces of outer sleeve snap ring grooves C1ssingle distance between outer faces of outer sleeve snap ring gro

33、oves D bearing outside diameter D1snap ring groove diameter d outside diameter of shaft E width of sector opening at diameter Fwof open sleeve type bearing Fwbore diameter of ball complement Fwssingle bore diameter of ball complement Fws minsmallest single bore diameter of ball complement 1)Kearadia

34、l runout of assembled bearing angle of sector opening (included angle) of open sleeve type bearing 1) The smallest single bore diameter of ball complement is the diameter of the cylinder which, when placed in the ball complement bore, results in zero radial clearance in at least one radial direction

35、. ISO 10285:2007(E) ISO 2007 All rights reserved 3Csdeviation of a single outer sleeve width C1sdeviation of a single distance between outer faces of outer sleeve snap ring grooves Dmpdeviation of mean bearing outside diameter in a single plane 5 Boundary dimensions Boundary dimensions for dimension

36、 series 1, 3 and 5 are given in Table 1. 6 Tolerances 6.1 Classes The degrees of precision to which linear ball bearings are manufactured are defined as tolerance classes L9, L7, L7A, L6, L6A, L6J and L6JA. The tolerance values are tabulated in Tables 2 to 8. For an overview of the basis for the tol

37、erance values, see Annex A. Tables 2 to 8 have been established on the basis of listing all the linear ball bearing tolerances for a given nominal bore diameter of ball complement (Fw). 6.2 Applicability Tolerance class L9 shall be applicable to series 1, closed and adjustable sleeve type bearings.

38、Tolerance classes L7 and L6 shall be applicable to series 1 and 3, closed sleeve type bearings. Tolerance classes L7A and L6A shall be applicable to series 3, open and adjustable sleeve type bearings. Tolerance class L6J shall be applicable to series 5, closed sleeve type bearings. Tolerance class L

39、6JA shall be applicable to series 5, open and adjustable sleeve type bearings. 6.3 Shaft tolerances For the proper functioning and performance of sleeve type linear ball bearings, it is essential that they are matched with shafts having dimensional and geometrical tolerances that are matched to the

40、size and series of the sleeve type linear ball bearing being used. Full details for the shafts suitable for use with the sleeve type linear ball bearings in this International Standard are specified in ISO 13012. NOTE The figure shows an example of the design. Figure 1 Bearing without snap ring groo

41、ves (for series 1) ISO 10285:2007(E) 4 ISO 2007 All rights reserveda) Bearing (side view) b) Closed sleeve type c) Adjustable sleeve type d) Open sleeve type NOTE The figure shows examples of the designs. Figure 2 Bearings with snap ring grooves (for series 3 and 5) ISO 10285:2007(E) ISO 2007 All ri

42、ghts reserved 5Table 1 Boundary dimensions Dimensions in millimetres and angles in degrees Series 1 Series 3 Series 5 b D1E b D1E FwD C D C C1min. max. min. min. D C C1min. max. min. min.3 7 10 7 10 4 8 12 8 12 5 10 15 12 22 14,2 1,1 11,5 10 15 10,2 1,1 9,6 6 12 22 13 22 14,2 1,1 12,4 12 19 13,5 1,1

43、 11,5 8 15 24 16 25 16,2 1,1 15,2 15 24 17,5 1,1 14,3 10 17 26 19 29 21,6 1,3 18 19 29 22 1,3 18 6 65 12 19 28 22 32 22,6 1,3 21 6,5 65 21 30 23 1,3 20 6,5 65 13 23 32 23 1,3 22 6,7 60 14 21 28 16 24 30 26 36 24,6 1,3 24,9 9 50 28 37 26,5 1,6 27 8 60 20 28 30 32 45 31,2 1,6 30,5 9 50 32 42 30,5 1,6

44、30,5 8,6 50 25 35 40 40 58 43,7 1,85 38,5 11 50 40 59 41 1,85 38 10,6 50 30 40 50 47 68 51,7 1,85 44,5 12,5 50 45 64 44,5 1,85 43 12,7 50 35 52 70 49,5 2,1 49 14,8 50 40 52 60 62 80 60,3 2,15 59 16,5 50 60 80 60,5 2,1 57 16,9 50 50 62 70 75 100 77,3 2,65 72 21 50 80 100 74 2,6 76,5 21,1 50 60 75 85

45、90 125 101,3 3,15 86,5 26 50 90 110 85 3,15 86,5 25,4 50 80 120 165 133,3 4,15 116 36 50 120 140 105,5 4,15 116 33,8 50 100 150 175 143,3 4,15 145 45 50 150 175 125,5 4,15 145 42,7 50 NOTE For the open and adjustable sleeve type bearings in series 3 and series 5, the D and D1dimensions apply after t

46、he bearing is split and fitted into a thick-section ring gauge of diameter D with zero deviation. ISO 10285:2007(E) 6 ISO 2007 All rights reservedTable 2 Tolerance class L9 for use with series 1, closed and adjustable sleeve type bearings Tolerance values in micrometres Fwmm Tolerances for Fws minaC

47、s u high low high low 3 +12,5 12,5 +180 180 3 5 +15 15 +215 215 5 6 +15 15 +260 260 6 10 +18 18 +260 260 10 18 +21,5 21,5 +260 260 18 20 +26 26 +260 260 20 30 +26 26 +310 310 30 50 +31 31 +370 370 50 80 +37 37 +435 435 aThe values give the limits of the difference between Fws minand Fwwhen the beari

48、ng is fitted into a thick-section ring gauge of diameter D with zero deviation. Table 3 Tolerance class L7 for use with series 1 and 3, closed sleeve type bearings Tolerance values in micrometres DmpbCsC1scFwmm Tolerances forFws minaSeries 1 Series 3 Series 1 Series 3 Series 3 u high low high low high low high low high low high low 3 +10 0 0 9 0 360 3 4 +12 0 0 9 0 430 4 5 +12 0 0 9 0 11 0 430 0 520 +270 0 5 6 +12 0 0 11 0 11 0 520 0 520 +270 0 6 8 +15 0 0 11 0 11 0 520 0 520 +270 0 8 10 +15 0 0 11 0 13 0 520 0 520 +330 0 10 18 +18 0 0 13 0 13 0 520 0 620 +

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1