1、111 1012311 0007928 768 111 Edition approved for publication AECMA STANDARD NORME AECMA AECMA NORM C5 Chairman Comments should be sent within six months after the date of publication to prEN 2043 Edition P 1 January 1996 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledell
2、e 94 - 8-1200 BRUXELLES - Tel. (32) 2 775 81 10 - Fax. (32) 2 775 81 11 ICs : 49.040.10 Descriptors : ENGLISH VERSION Aerospace series Metallic materials General requirements for semi-finished product qualification (excluding forgings and castings) Srie arospatiale Matriaux mtalliques Exigences gnra
3、les pour la qualification des demi-produits ( lexclusion des pices forges, matrices ou moules) Luft- und Raumfahrt Metallische Werkstoffe Allgemeine Anforderungen an die Qualifizierung von Halbzeug (Schmiedestcke und Gesenkschmiedestcke ausgenommen) This “Aerospace Series“ Prestandard has been drawn
4、 up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the p
5、ublication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the
6、Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. I 0 aecrna 1996 Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199, rue Jean-Jacques Rousseau - 921 38 ISSY-LES-MOULINEAUX
7、CEDEX 1996-01 -31 AECMA Gulledelle 94 B-1200 BRUXELLES Mr Odorico Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I 3032333 O009929 bT4 Page 2 prEN 20
8、43 : 1996 Contents list Introduction Scope Normative references Definitions Quality assurance Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1Ol123LL
9、0007730 31b W Page 3 prEN 2043 : 1996 O Introduction This standard is part of the series of EN metallic material standards for aerospace applications. It is only valid when used in conjunction with a technical specification from the original organization of these standards, according to the intermed
10、iate procedure as described in EN 4258 annex C, pending full introduction of the new organization as specified in EN 4258. 1 Scope This specification defines the general requirements for semi-finished product qualification of EN metallic materials (excluding forgings and castings). Specific requirem
11、ents are given in the material standards and/or relevant technical specification. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publicatio
12、ns are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 9002 Quality
13、systems - Model for quality assurance in production and installation EN 2000 Aerospace series - Quality assurance - EN aerospace products - Approval of the quality system of manufacturers EN 3042 Aerospace series - Quality assurance - EN aerospace products - Qualification procedure EN 4258 Aerospace
14、 series - Metallic materials - General organization of standardization - Links between types of EN standards and their use 1) TR 3040-2 Aerospace series - Quality assurance - EN aerospace products - Part 2 : List of qualified products 2) 1) 2) Published as AECMA Prestandard at the date of publicatio
15、n of this standard Published as AECMA Technical Report at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I L
16、OL23LL 0009931 252 I Page 4 prEN 2043 : 1996 3 Definitions For the purpose of this standard the following d 3.1 Semi-finished product See EN 4258. finitions apply NOTE : Called product in the rest of this standard 3.2 Established manufacturer A manufacturer who is well established in terms of his ma
17、nuf :turing facilities and has manufactured products for the aerospace industry for a number of years to recognized national or company aerospace specifications, and has obtained significant statistical data for those products. These manufacturers shall already hold some form of approval conforming
18、to IS0 9002 or to other national or company aerospace quality systems. 3.3 Established product A product manufactured to an existing national or company aerospace specification, which is accepted as an alternative to the EN material standard, and for which significant national data is available. 3.4
19、 New manufacturer A manufacturer who has not previously manufactured products for the aerospace industry. 3.5 New product A product which has not previously been manufactured, by an established or new manufacturer to a national or company aerospace specification. 3.6 Product pre-qualification Pre-qu
20、alification ; manufacturers data or screening tests to verify basic properties according to the requirements of the relevant material standard, and process routes. 4 Quality assurance 4.1 Approval of quality system See EN 2000. 4.2 Product qualification Product qualification shall be in accordance w
21、ith EN 3042. The product tested for qualification shall be manufactured on the same equipment and in accordance with the same specification and process procedures as the serial products. Product qualification to a material standard includes the manufacturers acceptance to a quality audit of the enti
22、re production procedure, from the raw material acquisition, through processing steps to batch release and the use of relevant standards including quality assurance documentation. If required a confidential audit can be carried out. Copyright Association Europeene des Constructeurs de Materiel Aerosp
23、atial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10L23LL 0009932 199 H Page 5 prEN 2043 : 1996 Adjustment of the manufacturing schedule to accommodate improved manufacturing techniques to the state of the art is the manu
24、facturers responsibility but may require requalification of the product to the material standard. As part of the product qualification, the mandated body reserves the right to carry out processing trials and/or product qualification tests in house or at an independent facility. All results of the pr
25、oduct qualification tests including reference to the manufacturing schedule shall be presented in a qualification test report (see subclause 4.2.4). Upon successful product qualification the manufacturers name and qualified product will be recorded in TR 3040-2. The qualification is directed to the
26、raw material specifications or sources and the equipment and the processes which have been identified in the manufacturing schedule. NOTE : To use a certain product in an aerospace application product qualification alone may not be sufficient ; additional pre-and/or post-qualification testing may be
27、 required by the user : - Pre-qualification : manufacturers data or screening tests to verify basic properties according to the requirements of the relevant material standard and process routes. The requirements shall be negotiated between the user and the mandated body ; - Post-qualification : spec
28、ific component tests when required separately specified as part of the project certification process. These component tests are the responsibility of the user who should also specify the requirements. 4.2.1 Tests Product qualification testing shall conform to the requirements specified in line 100 o
29、f the relevant material standard. For new products or new manufacturers this full qualification testing shall be required. If the product is already qualified by an aerospace company against a recognized material standard (e.g. national or company specification) the mandated body in conjunction with
30、 (potential) user/users, may, if sufficient data (a qualification test report) is available, waive all or part of the qualification requirements tests of the material standard. Reduction in qualification testing may also be considered for other cases, such as discontinued and re- started supply or t
31、he production of related product forms. If the manufacturer cannot perform the required testing, a material test laboratory acceptable to the mandated body shall be appointed. 4.2.2 Re-tests A re-test may be required when one or more test results do not meet the requirements of the product qualifica
32、tion test. A re-test shall be performed on products from the same batch or batches agreed with the mandated body. All test and re-test results shall be reported. Unsatisfactory test results may be cause for refusal of the qualification of the product. Copyright Association Europeene des Constructeur
33、s de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- LOL23LL 0009933 025 I Page 6 prEN 2043 : 1996 4.2.3 Test report The product qualification test report shall contain the following information : - manu
34、facturers name and address ; - relevant products ; - manufacturing schedule ; - material standard number ; - delivery condition and code ; - cast and batch numbers ; - tests and re-test results. 4.2.4 The manufacturer shall provide a safety data sheet prior to qualification testing. Safety data shee
35、t (if applicable) 4.2.5 Interpretation of test results The mandated body shall have full discretion in the interpretation of the requirements, and shall detail any exemptions and divergences in their recommendations/report. Where “unless otherwise specified“, “in case of dispute“ and/or “reference m
36、ethod“ appears in the technical standard, material standard, and/or the test method standard, the mandated body shall have full discretion in applying the requirements. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
