1、AECMA PREN2362 85 i-iOi2333 0007523 8 prEN2362 A. E .C .M .A. STAN DARD NORM E A.E .C .M .A. Edition 1 A.E.C.M.A. NORM February 1985 UDC : 629.7.05 : 621.854 : 621.85.052.004.1 Key words : Aircraft industry, flight control, flexible cable, cable end, crimping end piece, dimensions, breaking loads. E
2、NGLISH VERSION Aero P C serie Ball-ends in corrosion resisting steel swaged on type, control cable Dimensions and loads Srie arospatiale Embouts sphre terminale en acier rsistant la corrosion sertir sur cbles de commandes Dimensions et charges Luft- und Raumfahrt Seilschuhe mit Kugelkopf, einseitig
3、aus korrosionsbestandigem Stahl zum Aufquetschen auf Steuerseile Mae und Belastungen This industrial standard for the aerospace sector has been drawn upJ under the responsibility of AECMA (Associa tion Europenne des Constructeurs de Matriel Arospatial). it is published on yellow paper in three equiv
4、alent versions (English, French, German). It will be submitted to CEN (European Committee for Standardization) as a draft European Standard. Approved by The equivalent versions in French and German languages COMITE DE NORMALISATION can be supplied by B.NA., 8, rue Moreau-Vauthier of A.E.C.M.A. 1984-
5、0907 92100 BOULOGNE-BILLANCOURT - FRANCE. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Contents 1 2 References 3 Material and surface treatment 4 Re
6、quired characteristics 5 Designation 6 Marking 7 Technical specif cation Scope and field of application Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,
7、 AECMA PREN2362 85 m 10L23Ll 0007523 L mi prEN2362 Page 3 1 Scope and field of application EN2465 EN25 16 EPu2569 3 Ma This standard specifies the characteristics of corrosion resisting steel ball- ends suitable for swaging on to aircraft control cables. 2 References IS0 2020 - 1984, Aerospace - Me
8、chanical system parts - Preformed flexible steel wire rope for aircraft controls - Technical specification, , Steel FE-PA 11 - Softened - Bars De 100 mm , Passivation of corrosion resisting steels 1) , Control cable fittings and turnbarrel assemblies - Technical specification i). erial and surface t
9、reatment 3.1 Material Steel EN2465. 3.2 Surface treatment Passivation EN2516 1). 4 Required characteristics 4.1 Dimensions - Tolerances - Loads - Mass. The configuration shall correspond to figure and the dimensions shall conform to the values given in the figure and the table. 4.2 Surface roughness
10、 See figure. 15O t2 9 Figure 1) In preparation -. . -_ .- Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2362 85 LOL23LL 0007524 3 prEN2362
11、Page 4 56 I 5.6 I 14,23 I 1.9 1 5,6 I 3,85 64 6,4 16 2.1 6,3 4,30 1) No internal taper. TABLE Dimensions in millimetres Ma“s Minimum breaking load Og kN 2) - 0.1 O O o - 0,2 J L N P O + 0.5 + 0.1 + 0.2 - I 3.40 7 1.8 2 2.8 O, 5 2,15 4.30 10 2.6 2.9 3,6 12 4,45 5.70 I 13 I 3,5 I 3.9 I 4,8 I 2.6 I 8.9
12、0 I 6.60 16 4,3 4.7 5,6 4,3 12.45 7,58 18.7 5,l 5,6 6.4 6,4 18,60 24,90 10,33 3 1,20 2) Equal to the one of the cable used according to IS0 2020. 5 Dsignation Each ball-end for swaging on to cables shall only be designated as in the following example : Description block Identity block CABLE BALL-EMD
13、 EN2362-56 Number of EN 56 : Cable code, see table I Note : If necessary, originator code S9005 may be introduced between the description block and identity block. 6 . Marking In addition to the manufacturers own marking, each ball-ends for swaging on to cables shall be marked using the identity blo
14、ck as defined in clause 5 of this s tandard. The position and method of marking are at the manufacturers option. For ball-ends with code cable 16 and 24 marking shall be on the package only. 7 Technical specification The ball-ends for swaging on to cables supplied according to this standard shall conform with the requirements of EN2569 i). i) In preparation. . Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
