AECMA PREN 4248-1996 Aerospace Series Nuts Anchor Self-Locking Fixed Single Lug with Counterbore in Heat Resisting Steel Silver Plated Classification 1 100 MPa (at Ambient Tempera.pdf

上传人:priceawful190 文档编号:421200 上传时间:2018-11-06 格式:PDF 页数:5 大小:196.55KB
下载 相关 举报
AECMA PREN 4248-1996 Aerospace Series Nuts Anchor Self-Locking Fixed Single Lug with Counterbore in Heat Resisting Steel Silver Plated Classification  1 100 MPa (at Ambient Tempera.pdf_第1页
第1页 / 共5页
AECMA PREN 4248-1996 Aerospace Series Nuts Anchor Self-Locking Fixed Single Lug with Counterbore in Heat Resisting Steel Silver Plated Classification  1 100 MPa (at Ambient Tempera.pdf_第2页
第2页 / 共5页
AECMA PREN 4248-1996 Aerospace Series Nuts Anchor Self-Locking Fixed Single Lug with Counterbore in Heat Resisting Steel Silver Plated Classification  1 100 MPa (at Ambient Tempera.pdf_第3页
第3页 / 共5页
AECMA PREN 4248-1996 Aerospace Series Nuts Anchor Self-Locking Fixed Single Lug with Counterbore in Heat Resisting Steel Silver Plated Classification  1 100 MPa (at Ambient Tempera.pdf_第4页
第4页 / 共5页
AECMA PREN 4248-1996 Aerospace Series Nuts Anchor Self-Locking Fixed Single Lug with Counterbore in Heat Resisting Steel Silver Plated Classification  1 100 MPa (at Ambient Tempera.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 AECMA PRENx424B b L0123LL 0010540 314 Srie arospatiale crous river, freinage interne, fixes, simple patte, avec chambrage, en acier rsistant chaud, argents Classification : 1 100 MPa ( temprature ambiante) I425 OC 1 AECMA STANDARD NORME AECMA AECMA NORM I Edition approved for publication prEN 4248

2、Edition P 1 May 1996 C3 Chairman Comments should be sent within six months after the date of publication to PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - E-1 200 BRUXELLES - Tel. (32) 2 775 81 10 - Fax. (32) 2 775 81 11 ICs : 49.040.20 ENGLISH VERSION Aerospac

3、e series Nuts, anchor, self-locking, fixed, single lug, with counterbore, in heat resisting steel, silver plated Classification : 1 100 MPa (at ambient temperature) I425 OC Luft- und Raumfahrt Annietmuttern, selbstsichernd, einseitiger Flansch, mit zylindrischer Aussenkung, aus hochwarmfestem Stahl,

4、 versilbert Klasse : 1 100 MPa (bei Raumtemperaturl I 425 OC This “Aerospace Series Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by t

5、he experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the stan

6、dard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. 1996-05-31 AECMA Gulledelle 94 B-

7、1200 BRUXELLES Mr Arena 1 I I aecrna 190 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PRENx4248 96 m LOL23LII 0010542 II97 m Page 3 prEN 4248

8、: 1996 1 Scope This standard specifies the characteristics of self-locking, fixed, single lug anchor nuts, with counterbore, in heat resisting steel, silver plated. Classification : 1 100 MPa 1) / 425 OC 2) 2 Normative references IS0 3168 IS0 5855-2 IS0 5858 IS0 8788 EN 2000 EN 2424 EN 2786 EN 3042

9、TR 3791 Aerospace - Self-locking, fixed, single-lug anchor nuts with counterbore, classification 1 100 MPa / 235 OC Aerospace - MJ threads - Part 2 : Limit dimensions for bolts and nuts Aerospace - Self-locking nuts with maximum operating temperature less than or equal to 425 OC - Procurement specif

10、ication Aerospace - Fasteners - Tolerances of form and position for nuts Aerospace series -Quality assurance - EN aerospace products - Approval of the quality system of manufacturers Aerospace series - Marking of aerospace products Aerospace series - Electrolytic silver plating of fasteners 3) Aeros

11、pace series - Quality assurance - EN aerospace products - Qualification procedure Aerospace series - Materials for all metal self-locking nuts and thin wall inserts of temperature classes 9 425 OC 4) 1) Corresponds to the minimum tensile stress which the nut is able to withstand at ambient temperatu

12、re without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the dimen

13、sions., 3) Published as AECMA Prestandard at the date of publication of this standard 4) Published as AECMA Technical Report at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo

14、reproduction or networking permitted without license from IHS-,-,- AECMA PRENm46411 96 L01233L 0030543 023 m Page 4 prEN 4248 : 1996 3 Required characteristics 3.1 See figure 1 and table 1. Dimensions and tolerances are : in conformity with IS0 3168, expressed in millimetres and apply after surface

15、treatment. Details of form not stated are at the manufacturers option. The cap shall remain joined (type of attachment at the users discretion) to the nut at the maximum operating temperature. See test conditions in IS0 5858. Configuration - Dimensions - Masses 3.2 IS0 8788 Tolerances of form and po

16、sition 3.3 Materials TR 3791 3.4 Surface treatment EN 2786, thickness : - on external surfaces : 5 pm to 15 pm ; - on pitch diameter : 5 pm min. for nuts MJ6 and larger. Nuts MJ5 and smaller shall show complete coverage over complete profile. Copyright Association Europeene des Constructeurs de Mate

17、riel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PRENa4248 Diameter code 030 040 050 060 Remove sharp edges 0,l to 0,4 Thread 1) C D E F G H J2) K L M N3) P4) O R S T V Mass5) max. max. min. min. max. ma

18、x. rnax. max. max. rnax. max. a rnax. I0,25 2,s 1,6 1,8 23 2,l 3 2,5 - 43 MJ30,5-4H6H - - 66 - 4,6 6 17.7 3,2 - - MJ40,7-4H6H 6.4 8,5 4.4 2,2 6,2 8 23.7 5,8 1.1 11 13 MJ5x0,8-4H6H 0,4 7,4 9,5 8 5.5 2,4 7,3 9 25,2 6,9 - 11,4 13,4 - 3,5 23 MJ6xl-4H5H - 8,8 11 6.5 8,7 10 27,7 8,l 1.3 12,7 14,7 4 4 - 96

19、 3032333 0030544 TbT 9 080 MJ8xl-4H5H 100 MJl01.25-4H5H - 0,s Page 5 prEN 4248 : 1996 - 2,7 - 3,5 - 11,7 85 10,Q 13 29.7 9,Q I,? 15 18 3 5 5.7 7,5 - 83 - - 13 10,5 3 12,9 16,2 34,3 12 1,9 - - 4,5 3,5 6 6,6 11,5 Options : countersunk rivet holes (when specified by the user) may be dimpled or cut coun

20、tersunk (at the manufacturers option). Y-Y O o N N +I +I O O O o 9 s Flange or N 1- 1 be;optonal Form out-of-round in this area to achieve the self-locking torque requirement 2). Radius / I H I 1 nr Configuration with cap m 1) These values in micrometres apply before surface treatment. They do not a

21、pply to threads, punched holes or sheared edges, the surface texture of which will be as achieved by usual manufacturing methods. 2) Tooling marks are permitted in this area. Figure 1 Table I Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with

22、 AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- AECMA PRENa4248 b = 1012311 0010545 Tb Option Plain rivet holes Dimpled or countersunk rivet holes Plain rivet holes + cap Dimpled or countersunk rivet holes + cap Page 6 prEN 4248 : 1996 Code - (hyphen) K B A

23、4 Designation EXAMPLE : Description block Identity block Number of this standard ,.,O Rivet hole and cap code (see table 2) Diameter code (see table 1) NOTE : If necessary, the code 19005 shall be placed between the description block and the identity block. Table 2 5 Marking EN 2424, style N. See fi

24、gure 1. 6 Technical specification IS0 5858, except for : - Approval of manufacturers : see EN 2000 ; - Qualification of products : see EN 3042. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1