1、ASD STANDARD NORME ASD ASD NORM prEN 4639-005 Edition P 1 September 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION
2、Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 005: Removable alignment sleeve holder Product standard Srie arospatiale Connecteurs optiques rectangulaires, modulaires multivoies, frule 1,25, quips dun port
3、e sleeve dmontable Partie 005 : Porte sleeve dmontable Norme de produit Luft- und Raumfahrt Optischer Rechtecksteckverbinder, modular, multipin, Ferrulendurchmesser 1,25 mm, demontierbarer Zentrierhlsenhalter Teil 005: Demontierbarer Zentrierhlsenhalter Produktnorm This “Aerospace Series“ Prestandar
4、d has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments
5、. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be
6、submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdraw
7、ing any national standards conflicting with the EN. Edition approved for publication 30 September 2006 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de Materiel Aerosp
8、atial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-005:20062 Contents Page Foreword . 2 1 Scope 3 2 Normative references 3 3 Terms and definitions. 3 4 Required characteristics 3 4.1 General . 3 4.2 Dimensions R
9、emovable Alignment sleeve holder 3 4.3 Material and surface treatment 4 4.4 Optical, mechanical and climatic characteristics 4 5 Designation 5 6 Marking. 5 7 Technical specification. 5 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inqui
10、ries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo re
11、production or networking permitted without license from IHS-,-,-prEN 4639-005:20063 1 Scope This standard specifies the characteristics of removable alignment sleeve holder for a female optical module for rectangular modular multipin connectors. 2 Normative references The following referenced docume
12、nts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. EN 4639-001, Aerospace
13、series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 001: Technical specification. 1) EN 4639-002, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment s
14、leeve holder Part 002: List of product standards. 1) EN 4639-004, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 004: Female optical module Product standard. 1) EN EPX-001, Aerospace series Connector, elect
15、rical, rectangular, modular, rectangular inserts Operating temperature 175 C continuous Part 001: Technical specification. 2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4639-001 apply. 4 Required characteristics 4.1 General The removable sleeve h
16、older must be assembled onto the female insert as specified in EN 4639-004. 4.2 Dimensions Removable Alignment sleeve holder See Figure 1. 1) Published as ASD Prestandard at the date of publication of this standard. 2) In preparation Copyright Association Europeene des Constructeurs de Materiel Aero
17、spatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-005:20064 Key 1 Alignment sleeve 4 Module limit stop 2 12 cavities 5 Floating movement 0,98 to 1,30 3 5/64 hex. captive screw Figure 1 4.3 Material and surfac
18、e treatment See EN EPX-001. 4.4 Optical, mechanical and climatic characteristics See EN 4639-002. 1 3 2 4 5 View B Detail 12 identical cavities of the central screw on both side Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for
19、 ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4639-005:20065 5 Designation EXAMPLE Description block CONNECTOR, OPTICAL Identity bloc EN4639-005EF1201 Number of the basic standard Removable sleeve holder Arrangement code (see EN 4639-002) Material of alignment slee
20、ve (see EN 4639-002) 6 Marking The marking shall include the identification, the date of manufacture (year, week) and the name or trade mark of the manufacturer or conform to standard EN 2424, code P, if required. 7 Technical specification See optical contact product standard.3) 3) Performance is directly linked to optical contact and fibre technology. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-
