AIA NAS 6405-2002 Bolt Tension Hex Head Close Tolerance 6AL-4V Titanium Alloy Short Thread Reduced Major Thread Diameter Self-Locking and Nonlocking 160 ksi Ftu Rev 11 FSC 5305.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 98FTM1-1998 Method for Predicting the Dynamic Root Stresses of Helical Gear Teeth《预测螺旋齿的动态齿根应力的方法》.pdf

AGMA 98FTM10-1998 Local Coefficients of Friction in Worm Gear Contacts《蜗轮接触的局部摩擦系数》.pdf

AGMA 98FTM11-1998 Improving Pump Gear Geometry Through Secondary Gear Tooth Finishing《通过二档齿轮齿精整提高泵齿轮的几何精度》.pdf

AGMA 98FTM12-1998 Gear Refurbishment an Economical Approach for Aerospace Overhaul & Repair《齿轮翻新.航空大修和维修的一种经济方法》.pdf

AGMA 98FTM2-1998 Mesh Friction in Gearing《齿轮的啮合摩擦》.pdf

AGMA 98FTM3-1998 Basic Studies on Fatigue Strength of Case-Hardened Gear Steel - Effects of Shot Peening and or Barrelling Processes《渗碳硬化齿轮钢疲劳强度的基本研究.喷丸硬化和 或滚光加工的作用》.pdf

AGMA 98FTM4-1998 Effect of Uncontrolled Heat Treat Distortion on the Pitting Life of Ground Carburized and Hardened Gears《不受控制的热处理变形对于磨光 渗碳和硬化齿轮的点蚀寿命的影响》.pdf

AGMA 98FTM5-1998 Low Vibration Design on a Helical Gear Pair《螺旋齿轮副上的低振动设计》.pdf

AGMA 98FTM6-1998 Calibration of Master Gears on Coordinate Measurement Machines《坐标量测设备上的主齿轮的校准》.pdf