1、,9 -c s- A-A-50748 6 May 1987 Commercial Item Description HOLSTER HIP PISTOL SEMI-AUTOMATIC, 9MM . The General Service Administration has authorized the use of tinis commercial item description. scope : This commercial item description covers left and right hand hip holsters for use with the gbM, Mg
2、 semi-automatic pistol. Applicable Documents: Standards: FED-STD-75 1 Stitches, Seams and Stitching FED-STD-595 Color, Requirements for individual color chips, 3x5 MIL-STD- 130 Identification marking of U.S. Military property Drawings : 99A-RI.I-P, Holster, Hip, Pistol 9MM. ggA-LH-P, Holster, iiip,
3、Pistol, 9MM. Drawings available froin Warner Robins, ALC/CREMS Robins AFB, GA 31096-5609 Salient Characteristics: The holster shall be capable of interface and fit with the government furnished gMM, M9 pistol. There shall not be excessive interference when insertng and withdarwing the pistol, nor wi
4、ll they cause functioning of any of the pistol controls. - Y- The holster shall comply with the requirements as defined in the drawings and as called out in the contract or order. The holster shall be manu- factured from leather, thread, and required hardware (snaps/rivets). All stitching shall canp
5、ly with the requirements set forth in FED-STD-751, stitch type 301, 5 to 7 stitches per inch. Color : Holsters shall be black and conform to color number 27038 of FED-STD-595. - IdenLification Marking: l_l_ Each holster shall be indelibly marked with the letters ilUS1, part number, national stock nu
6、mber, manufacturerls name and FSCM code. conform to MIL-STD-130 and be in the size and location indicated on the applicable drawing. DISTRIBUTION STATEMENT A. Approved for public release: distribution is unlimited. Markings shall I FSC 1095 -A O THIS DOCUMENT CONTAINS 3 PAGES. Provided by IHSNot for
7、 ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-507LI LO W 9977774 OOLIL777 b A-A-50748 Wormanship : - Holsters shall be free of dust, grease, corrosion and other foreign matter. The finished holsters shall conform to the quality of product established by this documen
8、t and as called out in the contract or order. Repairs of Type 301 Stitching: - Repairs of type 301 stitching shall be as follows: a. vJhen thread breaks or bobbins run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimum of 2 stitches back of the end of
9、stitching. b. Thread breaks or one or more consecutive skipped or run-off stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. the defective area, continue a minimum of 2 stitches beyond the defective area onto the existing stitching, defective st
10、itching without damaging the materials and restitching in the required manner. The stitching shall start a minimum of 2 stitches in back of Loose stitching shall be repaired by removing the C. When making the above repairs, stitches shall enter and exit previously made needle holes. Thread Ends: I_-
11、y_. All-thread ends shall be trimmed to 1/8 inch maximum length. Certification: - - The contractor shall certify that the product offered meets the salient charac- teristics of this description, and that the product conforms to the producers own drawings, specifications, standards, and quality assur
12、ance practices, and is-the same product offered for sale in the commercial marketplace. nesses that cannot offer products with established commercial market accept- ability, may compete by submission of bid samples. (The Government reserves the rights to require proof of such conformance before firs
13、t delivery and thereafter as may be otherwise provided for under provisions of the contract.) Small busi- Packaging, - The items shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and provide product protection against loss and damage du
14、ring multiple shipments, handling, and storage. shipping container shall be in compliance with national motor freight classi- fication. order. The Shipping container shall be marked as specified in the contract Notes: Type I - Right Hand Type II - Left Wand t Provided by IHSNot for ResaleNo reproduc
15、tion or networking permitted without license from IHS-,-,-A-A-5 O 7 4 8 Known. AcceDtable Items: The following products are known to meet t3ne requirements of this CID: NSN - FSCM - Manufacturer -I- Mod el 50905 50905 BI ANCHI 99A-RH-P 1095-01 -21 1-7962 BI ANCiiI 99A-LH-P 1095-01-212-9200 Military Interests: - -I-p Custodian - Air Force - 99 Army - AR Navy - OS Preparing -I -I_- Acitivity Air Force - 84 Agent Air Force - 99 Project No. 1095-o230 -3- fl g, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
