1、A-A-58013 9999974 0129978 731 W A-A-58013 24 February 1993 COMMERCIAL ITEM DESCRIPTION This item description covers a self-propelled diesel-engine-driven pneumatic tired compact loader/backhoe. Salient characteristics: A. Design. cooled, diesel engine driven. The loader/backhoe shall be pneumatic ti
2、re mounted and water B. Engine. The engine shall be heavy duty water cooled, diesel with a minimum of three cylinders. The engine shall be equipped with an efficient fuel injection mechanism, fuel filter system, air cleaner of the oil bath or dry type filter, and a lubricating oil filter. produce 20
3、 hp at 3000 rpm. As a minimum, the engine shall C. Transmission. The transmission shall be a heavy duty hydrostatic transmission rated at least at 35 hp. D. Steering. Power steering with full size steering wheel. E. mes. rear axle shall have a minim rating of 3300 ponnds with positraction and 5300 f
4、oot pounds (minimum) output torque. The front axle shall have a minim capacity of 4000 pounds. The F. Frame. One piece. G. Loader/backhoe dimensions. - Width - not to exceed 50 inches Height - not to exceed 80 inches with ROPS Wheel base - not less than 58 inches H. utriqgers. Street pads shall be p
5、rovided when rewired, see “FS. I* - Backhog. minimum digging depth of 100 inches. The backhoe shall have a minim reach of 135 inches and a Beneifical comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: I WR AK/LZMB Rob
6、ins AEB, GA 31098-5609. FSC 3805 DISTRIBUTION STATEMENT A. un1 imi ted. Approved for public release; distribution is Licensed by Information Handling ServicesA-A-58013 9999974 O129979 b78 = A- A- 5 80 l 3 J. Backhoe bucket. The backhoe bucket shall be 16 inches wide and have a minimum capacity of 1.
7、8 cubic feet, unless otherwise specified, see NOTES. K. feet and a minim roll back of 35 degrees. The cutting edge shall be of high carbon steel. Front bucket. The front bucket shall have a minim capacity of 6 cubic L. 2300 psi, have a 7 gallon tank and a fim of 7 gpn at 3600 rpm. Hydraulic system f
8、or loader/backhoe. This system shall produce at least M. Rear tires. As specified for each location, see NOTES. N. Front tires. - 20.5 inches X 8 inches X 10 inches; 4 ply. O. Controls. Standard controls unless otherwise specified, See NOTES. P. Brakes. Hydrodynamic when hydrastatic drive is in neut
9、ral, otherwise independent disc brake with guard. Q. Battery. Heavy duty 12 volt maintenance free. R. Seat. High back, slide track, two position swivel lock with retractable seat belt. S. Lights. The head lights shall be halogen, flood type, sealed beam and replaceable. The front and rear working li
10、ghts shall be flood type, sealed beam and replaceable. An amber high output strobe light shall also be furnished. T. of the operators normal operating position shall be furnished: Instrumentation. The following instruments, convenient to and in full view 1. Voltmeter (or Ammeter) 2. Tachometer 3. Ho
11、urmeter 4. Fuel gauge 5. Oil pressure indicator 6. High coolant temperature indicator U. Safety. The loader/backhoe shall conform to Federal Laws and Regulations governing noise, air pollution and other health and safety requirements which are in effect for this type of equipnent at the time of cont
12、ract award. Also the following safety features shall be provided: (1) Neutral safety start switch. (2) Backup alarm. (3) ROPS conforming to SAE 51040. 2 Licensed by Information Handling ServicesA-A-58013 W 9999974 O129980 39T A-A- 5 80 13 (4) Slow moving emblem on rear of loader/ backhoe. V. unless
13、otherwise specified, and shall be equipped with Che necessary features to safely transport the machine from one site to another. The trailer shall have as a minimum the following features: Trailer. A flat bed trailer shall be provided with each ioader/Sacjcloe, (1) F-78 X 14.5 tires and wheels. (2)
14、7000 lbs GVW (3) Safety chains. (4) Two inch hard pine deck, 63 inches x 168 inches, minimum. (5) 10,000 ib hydraulic surge coupler. (6) Heavy duty ramps with ramp straps. (7) Adjustable lunette eye coupler. S1 ipper springs. (9) Heavy duty 10,000 lb top wind jack. DOT 1 i ght i ng . (Il) Primed and
15、 painted channel iron frame. D ring tie downs. (13) Diamond plate fenders. W. (with minor modifications, as that term is defined in DoD FAR Supplement 252.211-7012, Paragraph K-85 of the solicitation) of an established product previously produced and sold in substantial commercial quantities (exceed
16、ing the criteria at FAR 15.804-39(f)(2)(ii)(A) for at least three years immediately preceding the issuance date of the solicitation. furnished, or earlier models of it, absent minor modifications, shall have routinely been supported with spare/repair parts which were produced or sold in the normal c
17、ourse of business. At the time of delivery, the contractor shall furnish the Administrative Contracting Officer with verification of compliance with these requirements. “E To OFFERORS: following information on the vehicle (or its earlier models) being offered as a commercial item: The vehicle furnis
18、hed must be the latest model as of the date of award The vehicle Offerors shall provide, as part of their proposals, the (1) Total sales to the U.S. Government or to contractors for U.S. Government use during the three years immediately preceding the 3 Licensed by Information Handling ServicesA-A-58
19、013 m 9999974 OL2998L 22b m A-A-5 80 1 3 issuance date of the solicitation. (2) Total sales of the item to the general public during the three years immediately preceding the issuance date of the solicitation. (3) Length of time the item has been sold in the comnercial market pl ace. (4) Points of c
20、ontact and phone numbers of customers to which the item has been sold in the commercial market place. (5) Other pertinent information necessary to determine that the item is an established commercial item. Contractor certification. offered meets the salient characteristics of this description and co
21、nforms to the producers awn drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such confoxmance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The contractor shall
22、certify that the product Regulatory requirements. Recovered materials. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580, as amended, and as implemented by Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. Preservation, pa
23、ckaging, packing, labeling, and marking. Unless otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source to the rec
24、eiving activity, plus reshipment from receiving activity, and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities, labeling, and marking shall be as specified in the contract and/or order. Identification marking and data plates shall be in accorda
25、nce with MIL-STD-1223. NUIBS a. Unless otherwise specified the loader/backhoes, and the transporting Commercial manuals to include parts manual, and operation and trailer when required, shall be painted dark green, 24052 of FED-STD-595. maintenance manuals shall be supplied with each loader/backhoe.
26、 of each shall be supplied). loader/backhoe as required in this Commercial Item Description. b. (TWO copies c. Unless otherwise specified a trailer shall be provided with each d. Backhoe bucket size, if different. 4 Licensed by Information Handling ServicesA-A-58013 7799974 0129982 Lb2 m A-A-5 80 13 e. Type rear tires required. f. g. Hydraulic P.T.O., if required. h. Street pads, if required. Wobblestick/joystick type controls, when required. Custodian: AIR FORCE-99 Preparing Activity: AIR FORCE-84 Project number 3805-015 1 5 Licensed by Information Handling Services
