1、 . MIL-S-43b57 84 777770b 0375342 1 - -i - e- r. MIL-S-43659 5 August i969 MILITARY SPECIFICATION STOPPER, INFLATING TUBE, PNEUMATIC MATTRESS “his specification is mandatory for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification covers the requirements
2、for one type of stopper (see 6.1). 2. APPLICABLE WCITMENTS 2.1 The folluwing documents of the issue in effect on date of invitation for blds or request for proposal, fonn a part of this specification to the extent: specified herein: SPECIFICATIONS FEDERAL PPP-B-566 - Boxes, Folding, Paperboard. PPP-
3、B-636 - Box, Nberboard. PPP-B-665 Stay Material). PPP-B-676 - Boxes, Setup. PPP-F-320 (Container Grade), and Cut Shapes PPP-T-45 Sealing and Securing. - Boxes; Paperboard, Metal Stayed (Including- - Fiberboard; Corrugated and Solid, Sheet Stock - Tape, Gummed, Paper, Reinforced and Plain, for MILITA
4、RY MIL-R-3065 - Rubber, Fabricated Products. STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes . PSC 8465 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43659 4 9999906 0395343 3 R _ MIL-S-43659 MIL-S
5、TD-129 MIL-STD-147 MIL-STD-417 - Marking for Shipment and Storage. - Palletized and Containerized Unit Loads 40“ X 48“ Pallets, SUds, Runners, or Pallet-Type Base. - Rubber Compositions, Vulcanized General Purpose, Solid (Symbols and Tests) . DRAWINGS U. S. Army Natick Laboratories 2-3-99 - Mattress
6、, Pneumatic; Inflating Tube and Stopper. (Figure I is a miniature reproduction of the referenced drawing and is (Copies of specifications, standards, drawings, and publications required attached for information only.) by suppliers in connection with specific procurement functions should be obtained
7、from the procuring activity or es directed by the contracting officer.) The following documents form a part of this 2.2 Other publications.- specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall appl
8、y. National Motor Freight Classification Issued by National Motor Freight Traffic Association, Inc., Agent (Application for copies should be addressed to American Trucking Associations, ATTN: Tariff Order Section, 1616 P Street, N.W., Washington, D.C. 20036). Uniform Freight Classification (Applicat
9、ion for copies should be addressed to the Uniform Classification Committee Agent, Room 202, Union Station, 516 West Jackson Boulevard, Chicago, Illinois 60606) 3. REQUIREMENTS 3.1 First article.- When specified (see 6.2), before production is commenced, two stoppers from each mold cavity sball be su
10、bmitted to the contracting officer or his authorized representative for inspection as speci- fied in 4.2. ment of production but does not relieve the supplier of the responsibility fQr compliance with ail provisions of this specification. sample ehall be manufactured by the supplier in the same faci
11、iities to be used for the manufacture of the production items. The approval of the preproduction sample authorizes the commence- The preproduction Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - - MIL-S-43659 4 9 9997906 0375344 5 MIL-S-4 3 65 9 3
12、.2 Material.- 3.2.1 Stopper.- The stopper incorrect; illegible; of improper size, and interior) location, sequence or method of application. Any nonconforming component; component missing, Materiah damaged, or otherwise defective affecting service- abil?y. 4 Provided by IHSNot for ResaleNo reproduct
13、ion or networking permitted without license from IHS-,-,-Examine Workmawhip . _ MIL-S-43657 4 m 777770b 0375346 7 m MIL-S-43659 hfect Inadequate application of components, such as in- Bulged or dfstorted container. complete closure of container flaps, loose strapping, inadequate 8 tapling . Contents
14、 Number of items per package is more or less than WiHnber of intermediate packages is more or less than Not packaged as specified. required. 11 required . - 1) For this defect, one package from each container in the sample shall be exded. 4,3,1,1,4 Examination for pa1letzation.- An examination shall
15、 be made to determine that the palletization requireiaante of section 5 of this speci- fication are complied vith. lbt belw. for delivery. the end item inspection lot, fied in 4.3.1.1.5. Defects mhall be ocored in accordance with the The sample unit shall be one p8lletized unit load fully prepared T
16、he lot size shall be the nrimber of palletized unit loads in The inspection level and AQL shall be as speci- L Eranine Finished dimensions Defect Length, width, or height exceeds specified maximum requirement. Palletization Not M specified. Pallet pattern not as specified. Interlocking of load8 not
17、as specified. Load not bonded with required straps as specified. Weight Marllag Exceeds maximuai load limits . Omitted; incorrect; Illegible; of improper size, location, sequence or method of application. 4.3.1J.5 Inspection levels and AQLs.- The inspection levels for determining sample size and the
18、 AQLs expressed in defects per one hundred units, shall be 88 followa: Examination paragraph Inspection level E a metal etayed paperboard box conforming to style c of PPP-B-665; a setup paperboard box conforming to type I, variety i, class c, style 3 or 4 of PPP-B-676; or a fiberboard box conforming
19、 to style RSC, typu CF (variety SW) or SP, class domestic, grade 175 of PPP-B-636. dhensions of each box shall approxhate 6-3/4 inches in length, 6-1/2 inches in Width, and 4 inche0 in depth. guide only. Esch box shall be secured with ninimm 2 inch width gummed paper tape conforming to type III, gra
20、de B of PPP-T-45. Inside Approximate dimensions are futnihed 88 a 5.1.2 Level C.- Stoppers challbe packaged to afford adequate protection against physical damage during shipment from the supply source to the first receiving activity. tbis requirement. 5.2 Packing.- The supplier may use hie standard
21、practice when it meets Packing shall be level A, B, or C as specified (see 6.2). 5.2.1 Level A.- Eighteen hundred stoppers, packaged as specified in 5.1, shall be packed in a shipping container conforming to style RSC, grade V2s of PPF-B-636. width, and three in depth within the shipping container.
22、of each shipping container shall approximate 21-1/2 inches in length, 14 inches in width, and 13-1/2 inches in depth. as a guide only. reinforced in accordance with the appendix of PPP-B-636. Level A packages shall be packed flat three in length, two in Inside dimensions Approximate dimensions are f
23、urnished Ea& fiberboard container shall be closed, waterproofed, and 5.2.2 shall be type CF Level B.- packed in.a fiberboard ahipping container conforming to style RSC, Eighteen hundred stoppers, packaged as specified in 5.1, Level A (variety SW) or SF, class domestic, grade 275 of PPP-B-636. paw- s
24、hall be packed flat three in length, two in width, and three in depth within the shipping container. tainer shall approximate 21-1/2 inches in length, 14 inches in width, and 13-1/2 inch- in depth. Approximate dimensions are furnished as a guide only. Each shipping container shall be closed in accor
25、dance with method II as speci- fied in the appendix of PPP-B-636. Inside dimensions of each shipping con- . 5.2.2.1 When specified (Bec 6.21, the shipping container shall be a grade V3c or V3a fiberboard box fabricated in accordance with PPP-B-636 and closed ia eccordencs with the appendix of thr co
26、ntainax specification. container material my al80 br grads V4r of PPP-F-320. The ehippiag 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. - - II_ - - MIL-S-43659 4 9997906 0395348 2 m i MIL-S-43659 5 2.3 Level C - Stoppers packaged as specified i
27、n 5.1, shall be packed in a manner to heure carrier acceptance and safe delivery at destination at the lowest transportation rate for such supplies. Containers shall be in accordance with nifarm Freight Classification Rules or National Motor Freight Chussification Rules, 88 applicable. 5 5.3 Pal1eti
28、zation.- dleas otherwise Specified (see 6.2), stoppers, packed a specified in 5.2, shall be palletized in accordance with load type I of MIL-STD.147. straps in accordance with bonding means K and L. Pallet patterns shall be in accordance with the appendix of Mu-STD-147. Interlocking of loads shall b
29、e effected by reversing the pattern of each course. If the container is of a size which does not conform to any of the pallet patterns specified in MIL-STD-147, the pallet pattern used shall be approved by the contracting officer . Each prepared load shall be bonded with primary and secondary 5.4 Ma
30、rking.- In addition to any special marking required by the contract or order, interior packages, shipping containers, and palletized unit loads shall be marked in accordance with MIL-STD-129. : . 6. NOTES 6-.1 Intended we.- The stopper ie intended for use in the inflating tube of the pneumatic mattr
31、ess (MIL-M-10747). 6.2 Ordering data.- Procurement docunents should specify the following: . (a) Title, nmber and date of this specification. (b) First article.- When preproduction sample is required (see 3.1). (e) Selection of applicable levels of packaging and packing (see 5.1 and 5.2). required f
32、or level B packing (see 5.2.2.1). When palletization is not required (see 5.3) Custodians : Preparing activity: , () When weather-resiatant grade fiberboard shipping containers are (e) Amy - GL Aw-GL . Navy - SA Air Force - 82 Project No. 8465-0467 -Review activities : Nay - SA, MC Air Force - 45, 82 User activities: Navy - YD Air Force - 11 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIGS-43659 MIL-S-43657 4 777770b 0375347 4 M Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
