1、- MIL-T-B363B (2) 83 9777906 04bL971 L I MIL-T-8363B AMENDMENT 2 10 December 1990 SUPERSEDING AMENDMENT 1 20 May 1980 MILITARY SPECIFICATION TAPE AND WEBBING, TEXTILE, WOVEN, NYLON This amendment forms a part of Military Specification ML-T-8363B, dated 20 May 1980, and is approved for use by all Dep
2、artments and Agencies of the Department of Defense. PAGE 1 * 1.2, Classification, line 7, delete and substitute: “Type V webbing - 900 pounds breaking strength * 2. APPLICABLE DOCUMENTS, delete and substitute: “2. APPLJCABLE DOCUMENTS 2.1 Government documents 2.1.1 Specifications. standards. The fol
3、lowing specifications, standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, in the solicitatio
4、n (see 6.2).” PAGE 2 ( * Add: 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specified exemption
5、has been obtained. 3.1.1, Line 1: Delete “all types” and substitute “types I, II, III, and IV”. 1 of 4 FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T
6、-363B (2) 3 9999906 0463972 3 a MIL-T-8363B PAGE 8 * TABLE I., delete and substitute: TABLE I. Construction and phvsical proPerties I Tape Thickness (inch) (max) Width (inch) Weight (ozlyd) Breaking strength End in warp (min) total count . face and back binder stuffer (min) warp binder stuffer fille
7、r Picks per inch Ply of yarns O. 040 5/16+1/32 0.08(min) 350 121 84 16 (2 ends as 1) 21 60 1 1 1 1 0.030 711 6klI32 0.09 (min) 290 98 88 10 - 72 1 1 1 - 0.060 314i1116 O .5 O (max) 400 88 88 - 48 2(min) - - 313 2 -a Vebbing 0.085 3/4+1 I1 6 1.05(max) 2600 135 121 14 24 2 1 1 - 0.065 25/32+1/16 0.7O(
8、max) 900 87 32 4 10 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-3b3B (2) 3 I 777770b 04bL773 5 MIL-T-8363B PAGE 9 * 4.1, delete and substitute: “4.1 ResPonsibilitv for inspection. Unless otherwise specified in the contract or purchase ord
9、er, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use their own or any other faciities suitable for the performanc of the inspection requirements specified here
10、in, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Add: 4.1.1 Responsibility for compliance. All i
11、tems shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibi
12、lity of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptan
13、ce of defective material.” PAGE 15 * 4.4.2, line 5: Delete “except for breaking strength which shall be in accordance with 4.4.2.1.” PAGE 16 * TABLE EI, line 22: Delete “after abrasion (type V only) PAGE 17 * 4.4.2.1: Delete. * Figure 5: Delete. PAGE 18 3 I 442 114 108” Provided by IHSNot for Resale
14、No reproduction or networking permitted without license from IHS-,-,- MIL-T-8363B (2) 83 II 7777906 0463774 7 W MIL-T-8363B PAGE 19 * Add: “6.4 4 Breaking strength Nylon tape * Nylon webbing 6.5 Changes from mevious amendment. The margins of this amendment are marked with an asterisk or vertical lin
15、es to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the
16、 requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment.” Custodians: Navy - NU Air Force - 11 Preparing activity: Air Force - il (Project No. 8305-0343) Review activities: Army - GL DLA - CT Air Force - 45 I 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
