API STD 1104-2013 Welding of Pipelines and Related Facilities (TWENTY-FIRST EDITION ERTA 1 April 2014 ERTA 2 June 2014 ERTA 3 July 2014 ERTA 4 November 2015 ADD 1 July 2014 ADD 2 M_1.pdf
《API STD 1104-2013 Welding of Pipelines and Related Facilities (TWENTY-FIRST EDITION ERTA 1 April 2014 ERTA 2 June 2014 ERTA 3 July 2014 ERTA 4 November 2015 ADD 1 July 2014 ADD 2 M_1.pdf》由会员分享,可在线阅读,更多相关《API STD 1104-2013 Welding of Pipelines and Related Facilities (TWENTY-FIRST EDITION ERTA 1 April 2014 ERTA 2 June 2014 ERTA 3 July 2014 ERTA 4 November 2015 ADD 1 July 2014 ADD 2 M_1.pdf(129页珍藏版)》请在麦多课文档分享上搜索。
1、Welding of Pipelines and Related FacilitiesAPI STANDARD 1104 TWENTY-FIRST EDITION, SEPTEMBER 2013ERRATA 1, APRIL 2014ERRATA 2, JUNE 2014ERRATA 3, JULY 2014ERRATA 4, NOVEMBER 2015ADDENDUM 1, JULY 2014ADDENDUM 2, MAY 2016Special NotesAPI publications necessarily address problems of a general nature. W
2、ith respect to particular circumstances, local, state, and federal laws and regulations should be reviewed.Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy,
3、completeness, or usefulness of the information contained hearein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors, consultants, or other assignees rep
4、resent that use of this publication would not infringe upon privately owned rights.API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representatio
5、n, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.API publications are published t
6、o facilitate the broad availability of proven, sound engineering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publication
7、s is not intended in any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not repres
8、ent, warrant, or guarantee that such products do in fact conform to the applicable API standard.Classified areas may vary depending on the location, conditions, equipment, and substances involved in any given situation. Users of this Standard should consult with the appropriate authorities having ju
9、risdiction.Users of this Standard should not rely exclusively on the information contained in this document. Sound business, sci-entific, engineering, and safety judgment should be used in employing the information contained herein. All rights reserved. No part of this work may be reproduced, transl
10、ated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copyright 2013 American Petrole
11、um InstituteForewordThis standard was prepared by a formulating committee that included representatives of the API, the American Gas Association (AGA), the Pipe Line Contractors Association (PLCA), the American Welding Society (AWS), and the American Society for Nondestructive Testing (ASNT), as wel
12、l as representatives of pipe manufacturers and individuals associated with related industries.The purpose of this standard is to present methods for the production of high quality welds through the use of qualified welders using approved welding procedures, materials, and equipment. Its purpose is a
13、lso to present inspection methods to ensure the proper analysis of welding quality through the use of qualified technicians and approved methods and equipment. It applies to both new construction and in-service welding.The use of this standard is entirely voluntary and is intended to apply to weldin
14、g of piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, and nitrogen and, where applicable, to distribution systems.This standard represents the combined efforts of many engineers who are responsible for the design, construct
15、ion, and operation of oil and gas pipelines, and the committee appreciatively acknowledges their wholehearted and valuable assistance.Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use of any method, appar
16、atus, or product covered by letters patent. Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent.Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification.Should: A
17、s used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the specification. This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is desig
18、nated as an API standard. Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street,
19、 NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time extension of up to
20、two years may be added to this review cycle. Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005.Suggested revisions are invited and
21、 should be submitted to the Standards Department, API, 1220 L Street, NW, Washington, DC 20005, standardsapi.org.iiiContentsPage1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22、12 Normative References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Terms, Definitions, Acronyms, and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23、 23.1 Terms and Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.2 Acronyms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24、 . . . . . . . . . . 54 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- APISTD11042013WELDINGOFPIPELINESANDRELATEDFACILITIESTWENTYFIRSTEDITIONERTA1APRIL2014ERTA2JUNE2014ERTA3JULY2014ERTA4NOVEMBER2015ADD1JULY2014ADD2M_1PDF

链接地址:http://www.mydoc123.com/p-429951.html