ANSI ASTM F2206-2014 Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE).pdf
《ANSI ASTM F2206-2014 Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE).pdf》由会员分享,可在线阅读,更多相关《ANSI ASTM F2206-2014 Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE).pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2206 14 An American National StandardStandard Specification forFabricated Fittings of Butt-Fused Polyethylene (PE)1This standard is issued under the fixed designation F2206; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis
2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification establishes requirements for fabri-cated fittings intended for use with outside-d
3、iameter controlledpolyethylene pipe and tubing. These fittings are manufacturedby heat-fusion joining shape-modified polyethylene compo-nents prepared from pipe, molded fittings, sheet, billet, orblock. Included are requirements for materials, design,workmanship, minimum dimensions, marking, test me
4、thods,and quality control.1.2 Pressure rating of the fabricated-fitting design is beyondthe scope of this standard and shall be established by the fittingmanufacturer. This specification includes requirements for bothelevated temperature pressure-tests and short-term pressuriza-tion tests to demonst
5、rate a reasonable level of performance ofthe fabricated-fitting design at the pressure rating establishedby the fitting manufacturer.1.3 The pressure-tests requirements are specified by thefittingsequivalent (E) DR. The EDR specified is the DR of thepiping system for which the fabricated fitting is
6、intended to bebutt-fused.1.4 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be consideredas requirements of the standard.1.5 UnitsThe values stated in inch-pound units are to bereg
7、arded as standard. The values given in parentheses aremathematical conversions to SI units which are provided forinformation only and are not considered standard.1.6 The following safety hazards caveat pertains only to thetest methods portion, Section 9, of this specification. Thisstandard does not
8、purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D
9、1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2513 Specification for Polyethylene (PE) Gas PressurePipe, Tubing, and FittingsD3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlle
10、d Outside DiameterD3261 Specification for Butt Heat Fusion Polyethylene (PE)Plastic Fittings for Polyethylene (PE) Plastic Pipe andTubingF412 Terminology Relating to Plastic Piping SystemsF714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside DiameterF2619/F2619M Specificatio
11、n for High-Density Polyethylene(PE) Line PipeF2880 Specification For Lap-Joint Type Flange Adapters forPolyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in.to 65 in.F3034 Specification for Billets made by Winding MoltenExtruded Stress-Rated High Density Polyethylene(HDPE)2.2 Federal Standards:3Fe
12、d. Std. No. 123 Marking for Shipment (Civil Agencies)OPS Part 192 Title 49, Code of Federal Regulations2.3 Military Standard:3MIL-STD-129 Marking for Shipment and Storage2.4 ANSI/NSF Standard:4ANSI/NSF 61 for Drinking Water System ComponentsHealth Effects2.5 Plastic Pipe Institute:5TR-4 Listing of H
13、ydrostatic Design Basis (HDB), Hydro-static Design Stress (HDS), Strength Design Basis (SDB),1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved Dec. 1, 2014. Publish
14、ed January 2015. Originallyapproved in 2002. Last previous edition approved in 2011 as F2206 11. DOI:10.1520/F2206-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer t
15、o the standards Document Summary page onthe ASTM website.3DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA19111-5094 http:/quicksearch.dla.mil/4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Availab
16、le from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,Irving, TX 75062, http:/www.plasticpipe.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis intern
17、ational standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Comm
18、ittee.1Pressure Design Basis (PDB) and Minimum RequiredStrength (MRS) for Thermoplastic Materials or Pipe.3. Terminology3.1 Definitions are in accordance with Terminology F412and abbreviations are in accordance with Terminology D1600,unless otherwise specified.3.2 Definitions:3.2.1 butt-fusion end(s
19、), nthe butt end(s) of the fabricatedfitting intended for field fusion by the installer.3.2.2 billet, na mass formed from a single stress-ratedpolyethylene compound in the approximate shape of a thick-walled cylindrical shell. (See Specification F3034.)3.2.3 fabricated fitting, na fitting constructe
20、d from manu-factured polyethylene components or materials.3.3 Abbreviations:3.3.1 DIPSductile iron pipe size.3.3.2 DRdimension ratio.3.3.3 EDRequivalent dimension ratio. The DR of the pipeto which the fitting is to be joined.3.3.4 IPSiron pipe size.3.3.5 ODoutside diameter.4. Classification4.1 Gener
21、alThis specification establishes requirementsfor fabricated fittings intended for butt-fusion joining topolyethylene pipe.4.1.1 Fabricated fittings intended for use in the distributionof natural gas or other fuel gases shall also meet the require-ments of Specification D2513.5. Ordering Information5
22、.1 When ordering fittings under this specification includethe following information:5.1.1 Polyethylene compound (material designation or tradename).5.1.2 Style of fitting (3 piece tee, 5 segment 90 ell, etc.).5.1.3 Size:5.1.3.1 Nominal size of end connections.5.1.3.2 End configurations (for example,
23、 IPS or DIPS).5.1.3.3 System DR.6. Material6.1 Polyethylene materials allowed for use in fittings pro-duced in accordance with this specification shall be in accor-dance with the manufacturers fabricated-fitting design speci-fications. In addition:6.1.1 Polyethylene pipe used in the production of fi
24、ttings inaccordance with this specification shall meet the requirementsof Specification F714, D3035, F2619/F2619M or D2513.6.1.2 Molded PE fittings used in the production of fabri-cated fittings in accordance with this specification shall meetthe requirements of Specification D3261.6.1.3 Flange adap
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
2000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSIASTMF22062014STANDARDSPECIFICATIONFORFABRICATEDFITTINGSOFBUTTFUSEDPOLYETHYLENEPEPDF
![提示](http://www.mydoc123.com/images/bang_tan.gif)
链接地址:http://www.mydoc123.com/p-433057.html