1、Plastic SinksIAPMO/ANSI Z124.6-2007Revision of ANSI Z124.6-1997A N A M E R I C A N N A T I O N A L S T A N D A R DIAPMO / ANSIZ124.6 - 2007Revision ofANSI Z124.6 - 1997American National Standardfor Plastic SinksSecretariatInternational Association ofPlumbing and Mechanical OfficialsApproved May 8, 2
2、007American National Standards Institute, Inc.Approval of an American National Standard requires verification by ANSI that therequirements for due process, consensus, and other criteria for approval have been met bythe standards developer.Consensus is established when, in the judgement of the ANSI B
3、oard of Standards Review,substantial agreement has been reached by directly and materially affected interests.Substantial agreement means much more than a simple majority, but not necessarily una-nimity. Consensus requires that all views and objections be considered, and that a con-certed effort be
4、made toward their resolution.The use of American National Standards is completely voluntary; their existence does notin any respect preclude anyone, whether he has approved the standards or not, from man-ufacturing, marketing, purchasing, or using products, processes, or procedures not con-forming t
5、o the standards.The American National Standards Institute does not develop standards and will in no cir-cumstances give an interpretation of any American National Standard. Moreover, no per-son shall have the right or authority to issue an interpretation of an American NationalStandard in the name o
6、f the American National Standards Institute. Requests for inter-pretations should be addressed to the secretariat or sponsor whose name appears on thetitle page of this standard.CAUTION NOTICE: This American National Standard may be revised or withdrawn atany time. The procedures of the American Nat
7、ional Standards Institute require that actionbe taken periodically to reaffirm, revise, or withdraw this standard. Purchasers ofAmerican National Standards may receive current information on all standards by callingor writing the American National Standards Institute.Published byInternational Associ
8、ation of Plumbing and Mechanical Officials5001 East Philadelphia Street, Ontario, CA 91761Copyright 2007 by International Association of Plumbing and Mechanical OfficialsAll rights reserved.No part of this publication may be reproduced in anyform, in an electronic retrieval system or otherwise,witho
9、ut prior written permission of the publisher.Printed in the United States of AmericaAmericanNationalStandardContentsPageForeword .iii1 Scope and Purpose 11.1 Scope .11.2 Purpose 11.3 Normative References .11.4 Definitions .12 General Requirements.12.1 Materials12.2 Dimensions and Tolerances 12.3 Uni
10、ts for Testing12.4 Installation Instructions .12.5 Care, and Maintenance Instructions12.6 Identification23 Workmanship and Finish 23.1 Unit Preparation 23.2 Method of Inspection of Unit Surface.23.3 Surface Test.23.4 Subsurface Test .24 Structural Integrity of Complete Units .34.1 Drain Fitting Conn
11、ection (All Sinks) .34.2 Impact Tests 44.2.1 Point Impact (All Sinks).44.2.2 Knife Drop Test (Kitchen and Bar Sinks Only).44.2.3 Skillet Drop Test (Kitchen Sinks Only) .44.3 Load Test (Kitchen, Service, and Laundry Sinks Only).44.4 Vibration Test45. Physical Characteristics of Materials45.1 Colorfas
12、tness and Aging Test (Kitchen and Bar Sinks Only) 45.2 Stain Resistance Test (All Sinks)55.3 Wear and Cleanability Test (All Sinks) 55.3.1 Specimen Preparation.55.3.2 Wear Test .65.3.3 Cleanability Test 65.4 Cigarette Test (All Sinks)75.5 Chemical Resistance Test (All Sinks).75.6 Heated Pan Test (Ki
13、tchen Sinks Only) .75.7 Hot Wax Test (Kitchen Sinks Only).86. Additional Material Tests .86.1 Thermal Shock Resistance Test(Kitchen, Laundry and Service Sinks Only) .86.2 Thermal Shock Resistance Test (Bar Sinks Only ) .87 Provisions for Government Procurement .8Tables1 Test Applicability to Sinks .
14、22 Appearance Requirements 33 Reagents Used in Stain Resistance Test.54 Brush Rotation Schedule.6iPageFigures1 Holes for Faucet and Outlet92 Load Test for Drain Fitting Connection .123 Point Impact Locations .124 Brush Holder (Sled) (Z124 Wear Test) 135 Platform 7.0% Ethoxylated-alkyl-phenol(Monsant
15、o Sterox NJ or Rohm and Haas Triton X-100 were used); 8.0%Sodium-xylene sulfonate (Stepan Chemical Co. Stepan SXS was used); 1.5%Ethylene Glycol Monobutyl Ether (2-butoxylethanol) (Union Carbide ButylCellosolve was used); and 75.5% water.3 To hasten drying, surfaces shall be permitted to be wiped wi
16、th a clean chamoisleather or a clean, absorbent, lint-free material (for this test only).4 “A“ weight or dry 600-grit silicon carbide abrasive paper manufactured by 3MCompany was used in preparing this test method.5 Standard dirt shall consists of: 20 parts carbon black (pigment grade); 20 partsiron
17、 black (iron oxide, black); 20 parts calcium stearate; 5 parts 30W motor oil;1 part wetting agent (Rohm and 44 parts tapwater. All parts shall be measured by weight.IAPMO/ANSI Z124.6-2007Table 1 - Test applicability to sinksClass of SinksTest Kitchen Bar Laundry Service3 Workmanship or delamination.
18、Inspection for cracking and crazing shall be made using anink solution as described in Section 3.3.1.7. Provisions for Government ProcurementWhen required by Government procurement documents, theinformation defined in Appendix II shall be specified by thepurchasers.8IAPMO/ANSI Z124.6-20079IAPMO/ANSI
19、 Z124.6-2007 * Providing faucet openingis optionalKitchen Sink Faucet Openings*(spray hole size and location optional)(Number of openings optional)Indicates flat surrounding areafor faucet opening11-1/4“(286 mm)5-5/8“(143 mm)2-1/2“(63 mm)1-3/8“ 1/8“ dia.(34.92 mm 3.18 mm)4“(101.6 mm)4“(101.6 mm)1-1/
20、8“ dia. min.(28.6 mm)* Providing faucet openingis optionalBar sink faucet openings*(number of openings optional)Indicates flat surrounding areafor faucet mounting6-3/4“(171.4 mm)3-3/8“(85.7 mm)2-1/2“(63 mm)2“(50.8 mm)4“(101.6 mm)2-1/2“ dia.(63 mm)1-1/4“ 1/4“ dia.(32 mm 6 mm)* Providing faucet openin
21、gis optionalLaundry tray faucet openings*(number of openings optional)Indicates flat surrounding areafor faucet mounting4“(101.6 mm)4“(101.6 mm)Figure 1 - Holes for faucet and outlet10IAPMO/ANSI Z124.6-20076-3/4“(171.4 mm)1-1/4“ 1/4“ DIA.(32 mm 6 mm)* Providing faucet openingis optionalLaundry tray
22、faucet openings*(number of openings optional)Indicates flat surrounding areafor faucet mounting2“(50.8 mm)4“(101.6 mm)2-1/2“(63 mm)* Providing faucet openingis optionalService sink faucet openings*Indicates flat surrounding areafor faucet mounting8“(203.2 mm)1-1/2“ 1/8“ dia.(38.1 mm 3.18 mm)2-1/2“(6
23、3 mm)3/8“ min. flat(9.53 mm)3/8“ min. flat(9.53 mm)2“ - 2-1/4“ dia.(50.80 mm - 57.15 mm)3-1/2“ - 4“ dia.(88.9 mm - 101.6 mm)Kitchen and/or bar sink outlets Bar sink outletsFigure 1 (continued)11IAPMO/ANSI Z124.6-20073/8“ min. flat(9.53 mm)Service sink outlets3“ - 3-1/4“ dia.(76.20 mm - 82.55 mm)3/8“
24、 min. flat(9.53 mm)Laundry tray outlets1-7/8 “ - 2-1/4“ dia.(47.63 mm - 57.15 mm)15/16“ nom.(23.81 mm)1-1/2“ dia. nom.(38.1 mm)Flat surface7/8“ nom.(22.23 mm)NOTE: Installer to provide throughhole in outletLaundry tray outlets1-1/2“ NPSMSingle hole punchingsNote: All single hole punchings shall be1-
25、5/16“ min. to 1-1/2“ max. in diameter.See NoteFigure 1 (concluded)12IAPMO/ANSI Z124.6-2007LoadUnit installed in accordance withmanufacturers instructionsMinimum dimensionto obtainclearance - not toexceed 12“ (305 mm)24“ (610 mm)Figure 2 - Load test for drain fittings connectionImpact pointsFigure 3
26、- Point impact locations13IAPMO/ANSI Z124.6-20071-1/2“ 1-1/2“Adjustable nutsFront view Side view1/16“ 2-1/8“ 1-1/2“ 1/16“3/4“3/8“3/16“5/16“1/8“ 1/2“1/2“ 3/4“5-3/4“Drill & tap for6/32“ allen screws (typ) Drill clearance hole for a 6/32“ - 1-3/4“threaded studTop viewNOTE: For metric conversion, 1 in.
27、= 25.4 mmFigure 4 - Brush holder (sled) (Z124 wear test)17“8-1/2“ 3“1/2“1“17-3/4“2“1/4“1-1/2“6-3/4“6-1/2“3“1/2“Platform for wear tester(AG-8100)NOTE: Construction: acrylic sheet solvent cementedSpecimen mounting plate(AG-8100)NOTE: Construction: steel or aluminum 0.06“ - 0.100“ thick1/4“NOTE: For me
28、tric conversion, 1 in. = 25.4 mmFigure 5 - Platform & specimen mounting plate for wear tester14IAPMO/ANSI Z124.6-2007P3/4“ dia. ctsk 82 - 1 holeR“S” dr 1/8“ - 27 straight pipe tap 1 hole1“2-1/16“2-1/16“4-1/8“P Q #25 dr #10 - 24 tap - 1 hole1“1/4“1-49/64“ 1-49/64“3-17/32“1/2“21/32 27/32“1-1/2“1“3/8“1
29、/8“P2“1-1/2“1/4“ 1/4“1/8“ R#25 dr #10 - 24tap - 8 holes3/4“1-33/64“3-1/2“1/4“ MCut out 1“ 1-1/2“1/4“1/4“HJ#5 dr. thru7/16“ dia. ctsk 82 - 4 holes1-3/4“3/8“5/16“2-1/8“1/8“These 2 surfaces must beparallel & ea. assemblyTypical sectionNOTES: Brush block to be brightchrome plated all over.Stamp blocks b
30、efore plating with 1/2“ highnumbers 1 thru 45/16“NOTE: For metric conversion, 1 in. = 25.4 mmFigure 6 - Brush block detailsMaterial ListItem Required DescriptionH 1 Nylon Flat Stock 4.8 x 4.8 x 54.0 mm (3/16 x 3/16 x 2-1/8 in.)J 4 Stainless Steel Flat Soc. HD Screw #10-24 x 9.5 mm (3/8 in.)M 1 Soft
31、Gasket Rubber 3.2 x 38.1 x 88.9 mm (1/8 x 1-1/2 x 3-1/2 in.) LongP 1 Hard Brass 38.1 x 50.8 x 104.8 mm (1-1/2 x 2 x 4-1/8 in.) Bright Chrome PlatedQ 1 Brass Set Screw Cup Point #10-24 x 6.4 mm (1/4 in.)R 1 De Vilbiss Hose Connector for 3.2 mm (1/8 in.) I.D. Hose, 3.2 mm (1/8 in.) - 27 M. Thd. 31.8 m
32、m(1-1/4 in.) Long (Bright Chrome Plated)Atlas Material Testing Solution4114 Ravenswood AvenueChicago, IL 60613(773) 327-4520Fisher Scientific Company2000 Park Ln Dr.Pittsburgh, PA 15275(412) 490-8300Gardner/Neotec InstrumentDivision of Pacific Scientific1100 East West HighwaySilver Springs MD 20910(
33、301) 589-4747In-Sink-Erator Division of Emerson4700 21st StreetRacine WI 53406(800) 558-5700(262) 554-5432NAHB Research Center400 Prince Georges BoulevardUpper Marlboro MD 20772(301) 249-4000Sigma Motor, Inc.3 N Main StreetMiddleport NY 14105(716) 735-3115U.S. National CommitteeCIE National Bureau o
34、f StandardsWashington, DC 20234U.S. SilicaP.O. Box 187Berkeley Springs, WV 25411(800) 243-7500Union Carbide CorporationSubsidiary of the DOW Chemical Co.39 Old Ridgebury RoadDanbury, CT 06817(203) 794-200015IAPMO/ANSI Z124.6-2007Appendix I(Non Mandatory)Testing Equipment Suppliers16IAPMO/ANSI Z124.6
35、-2007Appendix II(Non Mandatory)Government Requirements(This appendix is not part of ANSI Z124.6 - 2007 but is included only to assist the Federal Governmentin the procurement of Plastic Sink Plumbing Fixtures covered by this Standard)II.1 SCOPEThis appendix covers requirements of the Federal Governm
36、ent for the procurement of Plastic Sink Plumbing Fixtures.II.2 APPLICABLE DOCUMENTThe documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this appendixto the extent specified herein.ANSI Z1.4 - Sampling Procedures and Tables for Inspection by Attr
37、ibutes.II.3 REQUIREMENTSII.3.1 Part or Identifying Number (PIN). The plumbing fixtures covered by this standard shall be identified by a PIN.This part number is intended for cataloging and ordering purposes (see II.6) and not for surface marking on the product. ThePIN shall be written as shown:PIN d
38、esignation Z124.6 - XXXXXXXXXXANSI document numberPart numbersII.3.1.1 Part Numbersa. First character denotes type.1 = Kitchen sink2 = Laundry tray3 = Service sink4 = Bar sinkb. Second character denotes style.A = Flat-rim (under mount)B = Flat-rim ledgeC = Self rimmingD = Rolled RimE = Integral Sink
39、 & TopF = Othersc. Third character denotes number of compartments.1 = One compartment2 = Two compartments3 = Three compartmentsd. Fourth character denotes nominal overall size (Length x Width).17IAPMO/ANSI Z124.6-2007 KITCHEN SINKOverall DimensionsSizeCode Without Integral Rim With Integral Rimmm (i
40、n.) mm (in.)A 406 x 533 (16 x 21) 432 x 559 (17 x 22)B 508 x 457 (20 x 18) 533 x 483 (21 x 19)C 610 x 457 (24 x 18) 635 x 483 (25 x 19)D 610 x 533 (24 x 21) 635 x 559 (25 x 22)E 762 x 457 (30 x 18) 787 x 483 (31 x 19)F 762 x 533 (30 x 21) 787 x 559 (31 x 22)G 813 x 533 (32 x 21) 838 x 559 (33 x 22)H
41、 914 x 533 (36 x 21) 940 x 559 (37 x 22)J 1067 x 533 (42 x 21) 1092 x 559 (43 x 22)K 1219 x 533 (48 x 21) 1245 x 559 (49 x 22)L 1372 x 533 (54 x 21) 1397 x 559 (55 x 22)M 1524 x 533 (60 x 21) 1549 x 559 (61 x 22)P 1676 x 533 (66 x 21) 1702 x 559 (67 x 22)R 1829 x 533 (72 x 21) 1854 x 559 (73 x 22)X
42、As specified As specifiedBAR SINKOverall DimensionsSizeCode Without Integral Rim With Integral Rimmm (in.) mm (in.)A 381 x 381 (15 x 15) 406 x 406 (16 x 16)B 432 x 508 (17 x 20) 457 x 533 (18 x 21)C 483 x 457 (19 x 18) 508 x 483 (20 x 19)D 584 x 432 (23 x 17) 610 x 457 (24 x 18)X As specified As spe
43、cifiedLAUNDRY TRAYSize Overall DimensionsCode mm (in.)A 584 x 546 (23 x 21-1/2)B 610 x 508 (24 x 20)C 610 x 533 (24 x 21)D 610 x 584 (24 x 23)E 1143 x 546 (45 x 21-1/2)X As specified18IAPMO/ANSI Z124.6-2007SERVICE SINKSize Overall DimensionsCode mm (in.)A 559 x 457 (22 x 18)B 559 x 508 (22 x 20)C 61
44、0 x 508 (24 x 20)D 610 x 610 (24 x 24)E 914 x 610 (36 x 24)X As specifiede.Sixth Fifth character denotes integral rim.1 = Required2 = Not requiredf. Sixth character denotes splash back.A = Required, with manufacturers standard heightB = Required, with specified height (See II.6)C = Not requiredg.Sev
45、enth character denotes mounting.1 = Counter top (under mount, self rimming, or integral mount)2 = Integral top with cabinet3 = Integral top without cabinet4 = Wall-hung5 = Legs6 = Trap standard7 = Floorh.Eighth character denotes faucet hole punching.A = One holeB = Two holesC = Three holesD = Four h
46、olesE = Nonei. Ninth character denotes faucet hole location.1 = Top2 = Wall3 = Not applicablej. Tenth character denotes color.A = WhiteB = As specified (see II.6)II.3.2 Standard Commercial Product. The Plumbing fixtures shall, as a minimum, be in accordance with the requirementsof this standard. Fea
47、tures which are a part of the manufacturers standard commercial product, shall be included in the plumb-ing fixtures being furnished. A standard commercial product is a product which has been sold or is being currently offeredfor sale on the commercial market through advertisements or manufacturers
48、catalogs, or brochures and represents the latestproduction model.19IAPMO/ANSI Z124.6-2007II.4 QUALITY ASSURANCE PROVISIONSII.4.1 Responsibility For Inspection. The contractor shall be responsible for the performance of all inspection requirementsas specified herein. The contractor may use his own or
49、 any other facilities suitable for the performance of the inspectionrequirements unless disapproved by the Government. The Government reserves the right to perform any of the inspectionsset forth in the standard where such inspections are deemed necessary to assure supplies and services conform to prescribedrequirements.II.4.2 Quality Conformance Inspection. Where specified (see II.6), a quality conformance inspection shall be performedon each sample selected (see II.4.3) to determine compliance with this standard and shall include the following:A. Examination
