ANSI IEEE N42.31-2003 Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.pdf

上传人:figureissue185 文档编号:435423 上传时间:2018-11-14 格式:PDF 页数:41 大小:310.66KB
下载 相关 举报
ANSI IEEE N42.31-2003 Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.pdf_第1页
第1页 / 共41页
ANSI IEEE N42.31-2003 Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.pdf_第2页
第2页 / 共41页
ANSI IEEE N42.31-2003 Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.pdf_第3页
第3页 / 共41页
ANSI IEEE N42.31-2003 Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.pdf_第4页
第4页 / 共41页
ANSI IEEE N42.31-2003 Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.pdf_第5页
第5页 / 共41页
亲,该文档总共41页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、ANSI N42.31-2003IEEE StandardsN42.31American National Standard forMeasurement Procedures forResolution and Efficiency ofWide-Bandgap SemiconductorDetectors of Ionizing RadiationPublished by The Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USA20 Augus

2、t 2003Accredited by the American National Standards InstituteSponsored by theNational Committee on Radiation Instrumentation, N42IEEE StandardsPrint: SH95166PDF: SS95166ANSI N42.31-2003American National Standard for Measurement Procedures for Resolution and Efficiency of Wide-Bandgap Semiconductor D

3、etectors of Ionizing RadiationSponsorNational Committee on Radiation Instrumentation, N42Accredited by the American National Standards InstituteSecretariatThe Institute of Electrical and Electronics Engineers, Inc.Approved 20 February 2003American National Standards InstituteAbstract: Standard measu

4、rement and test procedures are established for wide-bandgapsemiconductor detectors such as cadmium telluride (CdTe), cadmium-zinc-telluride (CdZnTe), andmercuric iodide (HgI2) that can be used at room temperature for the detection and quantitativecharacterization of gamma-rays, X-rays, and charged p

5、articles. Standard terminology anddescriptions of the principal features of the detectors are included. Included in this standard is anannex on interfering electromagnetic noise, which is a factor in such measurements.Keywords: cadmium telluride, cadmium zinc telluride, CdTe, charged particle, CZT,

6、electron-holepair, gamma rays, HgI, ionizing radiation, ion pair, MCA, mercuric iodide, multichannel analyzer,semiconductor detector, X-rayThe Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2003 by the Institute of Electrical and Electroni

7、c Engineers, Inc.All rights reserved. Published 20 August 2003. Printed in the United States of America.Print: ISBN 0-7381-3798-7 SH95166PDF: ISBN 0-7381-3799-5 SS95166No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written

8、 permission from the publisher.TERMS OF USE Please Read CarefullyThe Institute of Electrical and Electronics Engineers, Inc., (“IEEE”) owns the copyright to this Document in all forms ofmedia. Copyright of the text retrieved, displayed, or output from this Document is owned by IEEE and is protected

9、bythe copyright laws of the United States and by international treaties. The IEEE reserves all rights not expressly grantedto the user.Except as allowed by the copyright laws of the United States of America, applicable international treaties, or any licenseor agreement the user or the users employer

10、 may have entered into with the IEEE or one of its authorized distributors,the user may not copy and/or distribute copies of this Document, nor significant portions of the document, in any form,nor may the user post this document on any intranet, website, or database without prior written permission

11、 from theIEEE.Permission and/or requests for licenses should be directed to: Manager, Standards Licensing and Contracts+1-732-562-3804or in writing at:IEEE Standards AssociationManager, Standards Licensing and Contracts445 Hoes LanePiscataway, NJ 08854American National StandardAn American National S

12、tandard implies a consensus of those substantially concerned with its scope and provisions. AnAmerican National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. Theexistence of an American National Standard does not in any respect preclude anyone, whethe

13、r he has approved thestandard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conformingto the standard. American National Standards are subject to periodic reviews and users are cautioned to obtain the latesteditions.CAUTION NOTICE: This American N

14、ational Standard may be revised or withdrawn at any time. The procedures ofthe American National Standards Institute require that action be taken to affirm, revise, or withdraw this standard nolater than five years from the date of publication. Purchasers of American National Standards may receive c

15、urrentinformation on all standards by calling or writing the American National Standards Institute.Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute ofElectrical and Electronics Engineers, Inc., provided that the appropriate fee i

16、s paid to Copyright Clearance Center. Toarrange for payment of licensing fee, please contact Copyright Clearance Center, Customer Service, 222 RosewoodDrive, Danvers, MA 01923 USA; +1-978-750-8400. Permission to photocopy portions of any individual standard foreducational classroom use can also be o

17、btained through the Copyright Clearance Center.iv Copyright 2003 IEEE. All rights reserved.Introduction(This introduction is not part of ANSI N42.31-2003, American National Standard for Measurement Procedures forResolution and Efficiency of Wide-Bandgap Semiconductor Detectors of Ionizing Radiation.

18、)This standard is the responsibility of the Accredited American Standards Committee on Radiation Instrumentation, N42.The standard was approved on N42 letter ballot of 10 July 2002.ParticipantsAt the time it approved this standard, the Accredited Standards Committee on Radiation Instrumentation, N42

19、, had thefollowing members:Louis Costrell, ChairMichael P. Unterweger, Vice ChairSue Vogel, Administrative SecretaryOrganization Represented Name of RepresentativeAmerican Conference of Governmental Industrial Hygienists. Jesse LiebermanBattelle NW Laboratories Joseph C. McDonaldBicron . Joseph G. B

20、ellianChew, M.H. Jack M. SelbyCommerce Dept, U.S., NIST .Louis Costrell.Michael P. Unterweger (Alt.)Eberline Instruments .Mitchell TruittEnergy Dept, U.S., OHER/PCSRD Natesch VaramaEntergy-ANO .Ron SchwartzFemo-TECH Inc. . Richard StraubGamma-Metrics . Ernesto A. CorteGeneral Activities Inc. Karl Re

21、initzHealth Physics Society Joseph StencelInstitute of Electrical gamma rays, X-rays, and chargedparticles are covered. The measurement procedures described herein apply primarily to detector elementshaving planar, hemispherical, or other geometries in which charge carriers of both polarities contri

22、bute tothe output signal. When the devices are an integral part of a system, it may not be possible for a user to maketests on the detector alone. In this instance, tests on the detector element must be established by mutualagreement between the manufacturer and the user.1.2 PurposeThe purpose of th

23、is standard is to establish terminology and test procedures that have the same meaning toboth manufacturers and users. Not all tests described in this standard are mandatory, but those used tospecify performance shall be made in accordance with the procedures described herein. (Use of the word“shall

24、” indicates a mandatory requirement, “must” a physical one, and “should” means “recommended.”)1.3 AbbreviationsAbbreviations, defined in 3.3, are used liberally throughout this document.ANSIStd N42.31-2003 AMERICAN NATIONAL STANDARD FOR MEASUREMENT PROCEDURES FOR RESOLUTION2 Copyright 2003 IEEE. All

25、 rights reserved.2. ReferencesStandards referred to herein are listed below. The details of the test instruments and the test proceduresdescribed in two of the standardsIEEE Std 301-1988 and IEEE Std 325-1996are closely related tothose described in this document and are recommended as adjuncts to it

26、.DOE Report DOE/ER-0457T (May 1990), Standard NIM Instrumentation System.1IEEE Std 194-1977, IEEE Standard Pulse Terms and Definitions.2,3,4IEEE Std 300-1988 (Reaff 1993), IEEE Standard Test Procedures for Semiconductor Charged-ParticleDetectors.IEEE Std 301-1988, IEEE Standard Test Procedures for A

27、mplifiers and Preamplifiers used with Detectorsof Ionizing Radiation.IEEE Std 325-1996, IEEE Standard Test Procedures for Germanium Gamma-Ray Detectors.IEEE Std 759-1984, IEEE Standard Test Procedures for Semiconductor X-Ray Energy Spectrometers.IEEE Std 1160-1993, IEEE Standard Test Procedures for

28、High-Purity Germanium Crystals for RadiationDetectors.3. Definitions, symbols, and abbreviations3.1 DefinitionsSpecialized terms used in this standard plus some others that are relevant appear in this subclause. Most ofthe technical terms within the definitions are themselves defined here but, with

29、a few exceptions, are notcross-referenced. Terms used infrequently in the document are defined where they appear; they may or maynot be defined in this subclause.3.1.1 active region: A region of a detector in which charge created by ionizing radiation contributessignificantly to the output signal.3.

30、1.2 amplifier: An electronic instrument for increasing the amplitude of a signal.3.1.3 amplifier shaping time: A nonspecific indication of the shaped-pulse width issuing from a pulseamplifier.3.1.4 amplifier time constant: A misnomer for the width of the shaped pulse issuing from a pulse amplifier.S

31、ee: shaping-time index (t0.5).1Available from Louis Costrell, NIM Committee Chairman, or Michael Unterweger, NIM Committee Vice-chairman, both at NationalInstitute of Standards and Technology, Radiation Physics Division or from the National Technical Information Service, U.S. Dept. ofCommerce, Sprin

32、gfield, VA 22161.2The IEEE standards or products referred to in Clause 2 are trademarks owned by the Institute of Electrical and Electronics Engineers,Incorporated.3IEEE Std 194-1977 has been withdrawn; however, copies can be obtained from Global Engineering, 15 Inverness Way East, Engle-wood, CO 80

33、112-5704, USA, tel. (303) 792-2181 (http:/ publications are available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O. Box 1331, Piscataway,NJ 08855-1331, USA (http:/standards.ieee.org/).ANSIAND EFFICIENCY OF WIDE-BANDGAP SEMICONDUCTOR DETECTORS Std N42.31-2003Copyrigh

34、t 2003 IEEE. All rights reserved. 33.1.5 analog-to-digital converter (ADC): An instrument that digitally encodes electrical pulses accordingto their amplitudes. An ADC is usually part of a multichannel analyzer (MCA).3.1.6 area (of all or part of a spectral line): The counts accumulated within a sel

35、ected number of channelsin a spectral line.3.1.7 background: Unwanted counts that appear in a spectrum due to ambient radiation, to a test sourcecontaining emitters other than the desired ones, or to spectral distortions caused by pulse pile-up.3.1.8 background (ambient): The spectrum of ionizing ra

36、diation observed when a test source is replaced bya blank which is identical to the test source except for the absence of radioactivity.3.1.9 ballistic deficit (BD): The loss in signal amplitude that occurs when the charge collection time in adetector is a significant fraction of the amplifiers diff

37、erentiating time constant.3.1.10 bandgap: The energy difference between the bottom of the conduction band and the top of thevalence band.3.1.11 baseline (of an electrical pulse): The average of the levels from which a pulse departs and to whichit returns in the absence of an overlapping pulse (IEEE

38、Std 194-1977).3.1.12 baseline restorer (BLR): A circuit that rapidly restores the baseline following an amplifiers outputpulse (or train of pulses) to the level that existed before the pulse.3.1.13 bias, detector: The voltage applied to a detector to produce the electric field that sweeps out thesig

39、nal charge. 3.1.14 bias resistor: The resistor through which the bias voltage is applied to a detector.3.1.15 bipolar pulse: A signal pulse having two lobes, one above and the other below the baseline. Whenproduced by a linear filter network, the two lobes have the same area but not necessarily the

40、same peakamplitude.3.1.16 capacitance, detector: The electrical capacitance measured between terminals of the detector underspecified conditions of bias and frequency and with the amplitude of the signal used for the capacitancedetermination being small compared with the bandgap of the semiconductor

41、 comprising the detector.3.1.17 carrier: See: charge carrier.3.1.18 center line: See: peak center line.3.1.19 channel: Refers to the channels in a multichannel analyzer.3.1.20 charge carrier: A mobile electron or hole.3.1.21 charge collection time: The time required for a charge produced by an ioniz

42、ing event to be collectedat the terminal of a detector under the influence of the detector bias voltage.3.1.22 charge-sensitive preamplifier: An amplifier, preceding the main amplifier, in which the outputamplitude is proportional to the charge injected at its input and virtually independent of dete

43、ctor capacitance(IEEE Std 301-1988).3.1.23 contact: A conducting area applied to the surface of a detector to make electrical contact with it.ANSIStd N42.31-2003 AMERICAN NATIONAL STANDARD FOR MEASUREMENT PROCEDURES FOR RESOLUTION4 Copyright 2003 IEEE. All rights reserved.3.1.24 CR differentiator: A

44、 high-pass electrical filter section comprising a capacitor in series with thesignal path followed by a resistor across the path.3.1.25 (CR)m-(RC)n shaping: In an amplifier, the pulse shape produced by m CR high-pass filter sections(differentiators) in conjunction with n RC low-pass filter sections

45、(integrators), all with the same timeconstant. If the input signal is a step function and no other high-pass sections are in the signal path, the pulseshape is unipolar if m = 1, bipolar if m = 2. For unipolar pulses, the waveform is described by Ktnet/, whereK is a constant, t is time, and is the t

46、ime constant of the differentiator.3.1.26 dead layer: In a semiconductor detector, a layer (frequently associated with a contact region) inwhich no significant part of the energy lost by photons or particles can contribute to the resulting signal.3.1.27 dead time: The interval during which the secon

47、d of two events is lost or is recorded with an error inits amplitude.3.1.28 decay time constant: In the absence of a low-pass network preceding the point of observation, thetime for a single-exponential waveform to decay to the fraction 1/e of its original amplitude.3.1.29 depletion region: A region

48、 in which the mobile charge-carrier density is insufficient to neutralize thenet fixed charge density of donors and acceptors. In a diode-type semiconductor radiation detector, thedepletion region is the active (sensitive) region.3.1.30 depletion voltage: The voltage at which a junction detector bec

49、omes fully depleted.3.1.31 detector element: The semiconductor crystal including its contacts.3.1.32 detector, semiconductor radiation: A semiconductor device in which the production and motion ofexcess free carriers is used for the detection and measurement of incident particles or photons.3.1.33 differentiator: A high-pass filter network (usually a CR section) in which the waveform of the outputsignal approximates the mathematical derivative of the input waveform.3.1.34 discriminator: A circuit having a threshold below which signals applied to

展开阅读全文
相关资源
  • ANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdfANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdf
  • ANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdfANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdf
  • ANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdfANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdf
  • ANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdfANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdf
  • ANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdfANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf
  • ANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdfANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdf
  • ANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdfANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdf
  • ANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdfANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdf
  • ANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdfANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdf
  • ANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdfANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ANSI

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1