1、*- e“ r COMMERCIAL ITEM DESRIPTION APRON, LABORATORY, PLASTIC The General Services Administration has authorized the use of this commercial item description in preference to Military Specification MIL-A-41801. 1, CLASSIFICATION 1.1 Classification. This commercial item description covers aprons of th
2、e following types: Type I - Plain Type II - With pocket and trough 2. SALIENT CHARACTERISTICS 2.1 Design and construction, type I. The apron shall have a bib and tie tapes, approximately 22 inches long by one inch wide. The apron shall be approximately 45 inches long by 29 inches wide. The straight
3、area shall be approximately 35 inches long and shall be so cut that the neckline is approximately 10 inches wide. The apron and tie tapes shall be constructed of clear, colorless, poly- vinyl chloride plastic film with a minimum 0.008 inch thickness. perimeter of the apron shall have a 1/2 + 1/16 in
4、ch wide heat sealed hem. The tie tapes shall be heat sealed to the apron at the beginning of the bib and shall be reinforced to the apron with an extra strip of vinyl. The neck shall be heat sealed to the apron at each end of the 10-inch neckline width. The outside 2.2 Design and construction, type
5、II. The type II apron shall have all the characteristics of the type I apron and shall have an additional pocket and trough. The pocket shall be located in the center of the bib area and the trough shall be located at the bottom hem. The top of the pocket shall be approximately 3 inches down from th
6、e apron lap, the trough shall be 2-3/4 - + 1/4 inches high by the width of the apron. constructed of the same material and thickness as the type I apron. The edges of the pocket and trough shall be heat sealed, 1/8 inch minimum width. The pocket shall have a snap fastener. The male and female snap f
7、astener halves shall be reinforced with at least one extra layer of vinyl film where they are attached to the apron and pocket. The male and females halves shall be centered and shall be approximately 1-inch distance from the top of pocket. The pocket and trough shall be 3. QUALITY ASSURANCE FSC 841
8、5 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50068 3.1 Certification. The contractor shall certify that the product offered meets the salient characteristics o
9、f this description, conforms to the producers own drawings, specifications, standards, and quality assurance practices, and is the same as the product offered for sale in the commercial marketplace. Government reserves the right to require proof of such conformance prior to first delivery and therea
10、fter as may be otherwise provided for under the provisions of the contract. The 4. PACKAGING 4.1 Packaging. Each apron shall be folded in half across the length and then folded in half across the width. The folded apron shall measure approximately 23 by 15 inches. in a bundle and securely tied with
11、cotton tape or twine approximately 4 inches from each end. Twenty folded aprons of one type only, shall be neatly stacked 4.2 Packing. board shipping container conforming to style RSC-L, type CF, class domestic, variety SW, minimum grade 200 of PPP-B-636. container shall be fitted with a box liner c
12、onforming to type CF, class weather- resistant, variety DW, grade 275 of PPP-B-636. Aprons, bundled as specified above, shall be packed flat, five in depth within the shipping container. Approximate dimensions of the shipping container shall be 24 inches in length, 16 inches in width, and 8 inches i
13、n depth, Each container shall have the con- tents completely covered on the top and bottom with a sheet of 30 pound minimum basis weight kraft paper conforming to typ I, grade B of UU-P-268. shipping container shall be closed in accordance with the appendix of PPP-B-636. 4.3 Palletization. When requ
14、ired, aprons shall be palletized on a 4-way entry pallet in accordance with MIL-STD-147. shall be K and L, or O, or P and pallet pattern shall be number 3 of MIL-STD-147. One hundred aprons of one type only shall be packed in a fiber- The inside of each shipping Each Load type shall be Ia; bonding m
15、eans -_ - A-A-500bB B4 = 9999974 0047LOb 2 e e e 4.4 Marking. purchase order, unit packs, shipping containers, and palletized unit loads shall be marked in accordance with MIL-STD-129. In addition to any special markings required by the contract or 5. NOTES 5.1 Intended use, The aprons are used by m
16、ilitary personnel in hospital and dispensary laboratories. 5.2 Ordering data. a. Title, number, and date of this document. b. Type of pron required (see 1.1). c. When palletization is required (see 4.3). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
17、,-,-* -Y t i A-A-500b 4 7777974 0047207 4 M - - MILITARY INTERESTS: Custodians Army - GL Navy - N Air Force - 99 Review Act ivi t i es Army - MD Air Force - 82 DLA - CT User Activities Air Force - 45 Marine Corps - MC A-A-50068 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: Army - GL Project No. 8415-0575 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
