1、e- 84/45 MIL-B-833G 4 W 999970b 0371652 h MIL-B-833G 27 May 1988 SUPERSEDING MIL-B-833F 24 November 1980 MILITARY SPECIFICATION BELT, TROUSERS, COTTON WEBBING, WITH CLIP This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope This docum
2、ent covers cotton webbing trouser belts with attached end clips. g * 1.2 Classification. Belts shall be of the following types and size-as specified (see 6.2 : Type 1 - Black 174, 1-1/4 inch wide (with yellow brass end clip) (Navy, Marine Corps) Type II - Khaki 3709, 1-1/4 inch wide (with red brass
3、end clip) (Marine Corps) Type III - Khaki 3709, 1-1/4 inch wide (with yellow brass end clip) (Navy) Type IV - Blue 1089, 1-114 inch wide (with nickel silver end clip) (Air Force) (Navy) - Black 174, 1-114 inch wide (with yellow brass with Type v - White, 1-1/4 inch wide (with yellow brass end clip)
4、- Type VI black enamel finish end clip) (Army) Type VI1 - Black 174, 1-1/4 inch wide (with nickel silver end clip) (Navy) Type VI11 - White, 1-1/4 inch wide (with nickel silver end clip) (Navy) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in
5、improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using. the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8440 DISTR
6、IBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ _ I _- MIL-B-33G L( m 9979706 03711653 = MIL -B -8 3 3G Type IX - Blue 1089, 1-1/4 inch wide (yellow brass with black ename
7、l finish end clip) (Air Force) (Navy 1 Type x - Black 174, 1 inch wide (with nickel silver end clip) Type XI - White, 1 inch wide (with nickel silver end clip) Type XII - Black 174, 1 inch wide (with yellow brass end clip) (Navy 1 (Navy 1 Type XII1 - Khaki 3709, 1 inch wide (with yellow brass end cl
8、ip) (Navy) Type XIV - White, 1 inch wide (with yellow brass end.clip1 (Navy) Size - 33 Sf se * 35 Si ze - 39 Size 45 Size - 49 2. WPLI CABLE DOCUMENTS 2,t documents. * 2, T. 1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specifi
9、cation to the extent specified herein, Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODTSS) and supplement thereto, cited in the soZiitation, SPEQFI CATIONS FEDERAL PPP-B-636 L. Boxes
10、I Shipping, Fiberboard MIL-W-530 - Webbing, Textile, Cotton, General Purpose, Natural MIL-B-1963 - Buckles and Clips, End, Strap (For Belt, Trousers) MIL-L-35078 - Loads Unit: Preparation of Semiperishable or in Colors Subsistence Items; Clothing, Personal Equipment and Equipage; General Specificati
11、on For 2 I h 4 W F a- I c- F Q) 3 F! (u a- I c- F P rl a 5 8 x rl P m m ld ti P n g; rlm rl 4 Q)c hd a F a- I F F =l. E 8 I% rl a M a- I .- - H P 5 n c m 4 ec C d .cl ld E! m n ti rl *.i rl rn o i c I U (u a- I F F a, 2 3 (u a- I c- 7 H H H P a- I c .- X H .- X n t -2 d ti O ti L *rl B n m m ld Fi P
12、 g rl rl a, h 4 W F F a- t x o ld rl a M c H w n c m -!z r=! ti O F ti d a n v) m ld ti P g rl rl a, h 4 W F .- o O b M .rl x b4 d M F H H H X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -.- MIL-E-833G BL( 9779706 0373657 5 m MIL-B-833G 4. QUALI
13、TY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contract
14、or may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this document where such inspections are deemed necessary to
15、 assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this document shall become a part of the contractors overall inspection system or quality program. The absence
16、of any inspection requirement in the document shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. known defective material, either indicated or actual, nor does it co
17、mmit the Government to acceptance of defective material, Sampling in quality conformance does not authorize submission of 4.7.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is responsible for assuring that all specified dim
18、ensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. * 4.2 Classification of inspections. The inspection requirements specified
19、herein are classified as follows: a. b. Quality conformance inspection (see 4.4). First article inspection (see 4.3). * 4.3 First article inspection. When a first article is required (see 6,2), it shall be examined for the defects specified in 4.4.3 and 4.4.4. presence of any defect shall be cause f
20、or rejection of the first article. The 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance
21、 with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this document or applicable purchase document. I- I l 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-833G 4 777790b 0373658 7 I
22、MIL-B-833G 8 * 4.4.2 End item visual examination. The end item shall be examined for the defects listed in table II. belts. and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 4.0. The lot size shall be expressed in units of The sample unit shall be one
23、belt. The inspection level shall be II TABLE II. End item visual defects Examine Defects Webbing Any hole, cut, tear, or smash Not firmly and tightly woven, edge frayed or Broken or missing end or pick Spliced, (i.e., not one continuous piece) Wrong color for type of belt specified Width of webbing
24、not as specified in table I for scalloped class being examined Clip, end Size marking Omitted or misplaced Dents, nicks, abrasions or scratches on exposed surfaces Broken or malformed, failing to serve intended purpose; protective finish omitted; corroded area; burr or sharp edge Improperly clinched
25、 (i.e., prongs not fully embedded in webbing) Not centered on webbing as specified (i.e., edges of webbing are not equal distance from edges of end clip, 2 1/32 inch) End ofwebbing not set full depth in end clip Webbing does not lie flat within confines of end clip Black enamel finish is not adheren
26、t, e.g., it is blistered, peeling, flaking or cracked Wrong color for type belt specified Wrong finish for type belt specified Size of end clip not as specified in table I for class being examined Omitted, illegible, incorrect, misplaced, or size characters not as specified Cleanness Spots or stains
27、 clearly noticeable 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_ - I L flIL-B-833G 84 W 7777906 0371659 7 MIL-B-833G 4.4.3 End item dimensional examination. The end item shall be examined for * the finished length specified on Drawing 2-4-45.
28、 specified tolerance shall be scored as a defect. The lot size shall be expressed in units of belts. The sample unit shall be one belt. The inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. Any length not within the 4.4.4 Packaging examination.
29、 The fully packaged end items shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers, fully packaged. The inspection level shall be S-2 and the APL, expressed in terms of defects per bundped units, shall be 2.5. Examine Def eo t Marking (exter
30、ior Omitted; incorrect; illegible; of improper The sample unit shall be one shippin8 container and interior) size, location, sequence, or method of application Ma terials Any component missing, damaged, or not as specified Workmanship Inadequate, application of components, such as incomplete sealing
31、 or- closure of flap, improper taping, loose strapping, or inadequate stapling Bulged or distorted container Content Number of rolls per shipping container is more or less than required required I/ Number of belts per roll is more or less than Size or ty5e is not as indicated on container - 1/ - I/
32、For this defect, three roils from each shipping container in the sample shall be examined, * 4.4.5 Palletization examination. The fully packaged and palletized end The sample unit shall be one items shall be examined for the defects listed below. The lot size shall be expressed in units of palletize
33、d unit loads, palletized unit load, fully packaged. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6-5, 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - r MIL-B-33G 4 E 779770b 037Lbb0 5 E
34、 Examine MIL-B-833G Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Palletization Pallet pattern not as specified Interlocking of loads not as specified Load not bonded as specified Weight Exceeds maximum load limits Marking Omitted; incorrect; illegible; of
35、 improper size, location, sequence, or method of application 5. PACKAGING 5.1 Preservation. Preservation shall be level A or Commercial, as specified (see 6.2). 5.1.1 Level A. Five belts of one type and size only shall be evenly stacked with the clips at one end. into a roll with the clips on the in
36、side and secured with cotton tape, twine, or pressure-sensitive tape to form a unit pack. The belts shall then be tightly rolled * 5.1.2 Commercial. Belts shall be preserved in accordance with ASTM D 3sl. 5.2 Packing. Packing shall be level A, B, or Commercial, as specified (see 6.2). * 5.2.1 Level
37、A packing. Belts of one type and size only, preserved as- specified in 5.1, shall be packed in a snug-fitting fiberboard shipping container conforming to style RSC, grade V2s of PPP-B-636. shall be packed as shown in Drawing 2-1-545. shipping container shall be approximately 15-1/2 inches in length,
38、 11-9/16 inches in width, and 7-1/8 inches in depth. are furnished as a guide only. Corrugated fiberboard filler pads shall be used to fill voids. Each shipping container shall be closed in accordance with method III, waterproofed in accordance with method V, and reinforced as specified in the appen
39、dix of PPP-B-636, except that the inspection shall be in accordance with 4.4.4. Type I through type IX belts shall be packed 110 per shipping container and type X through type XIV belts shall be packed 130 per shipping container. accordance with MIL-L-35078 for the type and class of unit load specif
40、ied (see 6.2). When unit loads are strapped, strapping shall be limited to nonmetallic strapping, except for type II, class F loads. Level -unit packs Inside dimensions of each Approximate dimensions Shipping containers shall be arranged in unit loads in L 9 Provided by IHSNot for ResaleNo reproduct
41、ion or networking permitted without license from IHS-,-,-_p_s -_ - MIL-B-33G 4 m 777770b 037Lbbl 7 MIL-B-833G 5.2.2 Level B packing. Belts of one type and size only, preserved as specified in 5.1, shall be packed in a snug-fitting fiberboard shipping container conforming to style RSC, type CF (varie
42、ty SW) or SF, class domestic, grade 275 of PPP-B-636. Level A unit packs shall be packed as shown in Drawing 2-1-545. Inside dimensions of each shipping container shall be approximately 15-1/2 inches in length, 11-9/16 inches in width, and 7-1/8 inches in depth. Approximate dimensions are furnished
43、as a guide only. Corrugated fiberboard filler pads shall be used to fill voids. Each shipping container shall be closed in accordance with method II as specified in the appendix of PPP-B-636, except that the inspection shall be in accordanas with 4.4.4. Type I through type IX belts shall be packed 1
44、10 per shipping container and type X through type XIV belts shall be packed 130 per shipping container. 5.2.2.1 Weather-resistant fiberboard containers. When specified (see 6.21, the shipping container shall be a grade VC, VS, or V4s fiberboard box fabricated in accordance with PPP-B-636 and closed
45、in accordance with method III as specified in the appendix of PPP-B-636, except that the inspection shall be in accordance with 4.4.4. * 5.2.3 Commercial packing. Belts, preserved as specified in 5.1, shall be packed in accordance with ASTM D 3951 * 5.3 Palletization. When specified (see 6.21, belts
46、, packed as specified in 5.2.2 and 5.2.3, shall be palletized on a 4-way entry pallet in accordance with load type Ia of MIL-STD-147. type IV or type V in accordance with MIL-STD-147. Pallets shall be fabricated from wood groups I, TI, III, or IV of MIL-STD-731. Each prepared load shall be bonded wi
47、th primary and secondary straps in accordance with bonding means K and L or film bonding means O or P. Pallet pattern shall be number 9 in accordance with the appendix of MIL-STD-147. effected by reversing the pattern of each course. Pallet type shall be type I (4-way entry), Interlocking of loads s
48、hall be 5.4 Marking. Tn addition to any special marking required by the contract or purchase order, shipping containers and palletized unit loads shall be marked in accordance with MTL-STD-129 or ASTM D 3951, as applicable. 6. NOTES 6.1 Intended use. The belts are used by Army, Navy, Marine Corps, a
49、nd Air Force personnel, 6.2 Ordering data. Acquisition documents should specify the following: a, Title, number, and date of Chis document. b. Type and size required (see 1*2). c, When a first article is required (see 3.1, 4.3, and 6.4). d, Selection of applicable levels of preservation and packing (see 5.1 and !je,?). 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
