1、2 BY -4s MIL-C-43 6 89C 31 March 1987 SUPERSED I NG MIL-C -436 8 9B 30 September 1977 MILITARY SPECIFICATION COVER, WATER CANTEEN, 2-QUART, COLLAPSIBLE (WITH PILE LINING) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This doc
2、ument covers one type and size of cover, for a collapsible canteen, made of olive green nylon duck and acrylic fiber pile with a cotton webbing sling. 2. APPLICABLE DOCUMENTS .w 2.1 Government documents. * 2.1.1 Documents. The following documents form a part of this document to the extent specified
3、herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL A-A-203 - Paper, Kraft, Untreated V-T-285 - Threa
4、d, Polyester Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to U.S.: Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014, by using the self -addressed Standardization D
5、ocument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release;. distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DDD-L
6、-20 PPP-B-636 MIL I TARY .MIL-S-1698 MIL-R-3390 MIL -W-4 088 MIL-T-5038 MIL-C-7219 MIL-H-9890 MIL-W-1733 7 MIL-E -206 52 / 1 MIL-F-2 1840 MIL-W-27265 MIL-L-35078 MIL-(2-43 128 MIL-C -43 25 1 MIL -F-4 3 51 4 STANDARDS FEDERAL FED-STD-751 MILITARY MIL -STD -105 MIL-STD -1 29 MIL-STD-147 MIL -STD -7 3
7、1 MIL-C -4 3 68 9C - Label: for Clothing, Equipage, and Tentage, - Boxes, Shipping, Fiberboard (General Use) - Slings, Bag and Case, Carrying - Rings, Dee - Webbing, Textile, Woven Nylon - Tape, Textile and Webbing, Textile, Reinforcing, - Cloth, Duck, Nylon - Hardware, Individual Load Carrying Equi
8、pment: - Webbing, Textile, Woven Nylon - Eyelet, Metallic, Rolled Flange Type, and Eyelet - Fastener Tapes, Hook and Pile, Synthetic - Webbing, Textile, Woven Nylon Impregnated - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specific
9、ation For - Cloth, Plain Weave, Nylon: Water Repellent, OG- 10 6 - Cloth, Pile, Synthetic Fiber Pile - Fastener, Plastic, for Equipage Items Nylon and Hardware, Miscellaneous Washer - Stitches, Seams, and Stitchings - Sampling Procedures and Tables forInspection - Marking for Shipment and Storage -
10、Palletized Unit Loads - Quality of Wood Members for Containers and Pallets by Attributes * 2.1.2 Other Government documents. The following other Government documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the da
11、te of the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-Ll3L9C 84 9997906 0395506 5 - MIL-C-436 89C DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2-2-279 - Cover, Water Canteen, 2-Quart, Collapsible (
12、With 2-2-280 - Cover, Water Canteen, 2-Quart, Collapsible (With 2-2-281 - Cover, Water Canteen, 2-Quart, Collapsible (With Pile Lining); Assembly and Sections Pile Lining) ; Details Pile Lining); Details (Copies of documents required by contractors in connection with specific acquisition functions s
13、hould be obtained from the contracting activity or as directed by the contracting activity.) % 2.2 Other publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those lis
14、ted in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. COLOR ASSOCIATION OF THE UNITED STATES Standard Color Refer
15、ence of America (Application for copies should be addressed to the Color Association of the United States, Inc., 343 Lexington Avenue, New York, NY 10016.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addresse
16、d to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 3 Provided by IHS
17、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- li_ -Is_l_ - MIL-C-43b7C 4 a 777970b O395507 7 a MIL-C-43689C * 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall t
18、ake precedence. Nothing in this document, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3 REQUIREMENTS 3.1 Guide samples. Guide samples of the end item are solely for guidance and information to the contractor (see 6.3). Variation from this d
19、ocument may appear in the sample, in which case this document shall govern. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.4). 3.3 Materials. (See 6.5) 3.3.1 Cloth, duck, nylon. The 7.25 ounce nylon du
20、ck shall conform to type III, class 3 of MIL-C-7219. The color shall be Olive Green 106. 3.3.2 Cloth, nylon. The 3.8 ounce nylon cloth shall be Olive Green 106, water repellent, conforming to MIL-C-43128. 3.3.3 Cloth, acrylic fiber pile. The cloth for lining the canteen cover shall conform to class
21、1 or 3 of MIL-C-43251 except that the requirements for color matching, dullness, and colorfastness shall not apply. 3.3.4 Fastener tape, hook and pile. The hook and pile nylon tape fastener shall be dyed Olive Green 106 and shall conform to type II, class 1, 5/8 inch width of MIL-F-21840. 3.3.5 Webb
22、ing, nylon. 3.3.5.1 3/4 inch and 2 1/4 inch widths. . The 3/4 inch and 2 1/4 inch nylon webbing shall be dyed Olive Drab 7 and shall conform to types Ia and XXVIII, respectively, of MIL-W-4088. 3.3.5.1.1 Treatment. The types Ia and XXVIII nylon webbing shall be resin impregnated to conform to class
23、R of MIL-W-27265. 3.3.5.2 1 inch width. The 1 inch nylon webbing used for the reinforcement shall conform to class 2 of MIL-W-17337. The color shall be Olive Drab 7. 3.3.6 Tape, nylon. The nylon binding tape shall be dyed Olive Drab 7 and shall conform to type III, 1 inch of MIL-T-5038. 4 Provided b
24、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 MIL-C-43689C 84 m 7777906 0395508 9 MIL-C-43 68 9C 3.3.7 Thread, polyester. The thread for all stitching shall conform to type I, class 1, sub-class B, size E of V-T-285. 3.3.7.1 Color. The thread shall be dyed
25、 Olive Drab S-1 (C.A. 66022) and shall show fastness to weathering equal to or better than the standard sample. If no standard sample is available, the thread shall show good fastness to weathering. 3.3.8 Fastener, plastic. The plastic fastener shall be black and shall conform to MIL-F-43514. 3.3.9
26、Eyelet, aluminum black. The black enameled aluminum eyelet shall conform to dash No.-ABE 131 of MIL-E-20652/1. 3.3.10 Ring, dee. The dee ring shall conform to class 1 or class 2, configuration A, 25/32 inch by 3/8 inch of MIL-R-3390. 3.3.11 Keeper with slide. The keeper with slide shall conform to t
27、ype X of MIL-H-9890. 3.3.12 Sling. The sling shall conform to type I of MIL-S-1698. 3.4 Construction. The construction shall conform in all respects to Drawings 2-2-279 through 2-2-281 and as specified herein. 3.4.1 Stitches, seams, and stitching. All machine stitching except bartacking shall confor
28、m to FED-STD-751. All stitching except bartacking shall be stitch type 301, 8 to 10 stitches per inch. 3.4.1.1 Automatic stitching. Any of the stitching operations cited in this document may be performed with an automatic machine provided that the requirements for stitch pattern, stitches per inch,
29、and size and types of thread are met and that at least three tying, overlapping, or back stitches are used to secure the ends of stitching. 3.4.1.2 Type 301 Stitching. Ends of all stitching except box and w-w shall be backstitched or backtacked not less than 1 inch at the ends, except where ends are
30、 caught in other seams and stitching. On box and W-W stitching, all ends shall be backstitched or backtacked 1/2 inch. Thread tension shall be maintained so that there will be no loose or tight stitching and the lock will be embedded in the sewed material. Provided by IHSNot for ResaleNo reproductio
31、n or networking permitted without license from IHS-,-,-MIL-C-43689C 3.4.1.2.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks, skipped stitches, run-Offs, or bobbin run-outs occur during sewing, the stitching shall be repaired by restarting the
32、 stitching a minimum of 1 inch (i/Z inch for box and W-W stitching) back of the end of the stitching. L( b. Thread breaks, or two or more consecutive skipped or run-off stitches, noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall star
33、t a minimum of 1 inch in back of the defective area (1/2 inch for box and W-W stitching), continue over the defective area and continue a minimum of 1 inch (1/2 inch for box and W-W stitching) beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repair
34、ed by removing the defective stitching, without damaging the materials and restitching in the required manner. lJ L/ When making the above repairs, the ends of the stitching are not required to be backstitched. n 3.4.1.3 Bartacking. Unless otherwise specified, bartacks shall be as listed in table I.
35、 The bartack shall be free from thread breaks and loose or tight stitching. TABLE I. Bartack requirements Length Width Tolerances (inches) Stitches (inches) . (inches) Length Width per bartack C. 1/2 1 /8 f. 1/16 f 1/32 28 3/4 118 f 1/16 f 1/32 42 3.4.1.4 Thread ends. All thread ends shall be trimme
36、d to 1/4 inch maximum length. 3.4.1.5 Lubrication of thread. There shall be no lubrication of.the thread prior to or during sewing (see 4.4.2). 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* flIL-C-43689C 4 = 9979906 0395510 7 MIL -C-4 36 89C 3.
37、4.2 Eyelet, aluminum. A hole shall be prepunched through the nylon duck and acrylic fiber pile cloth before inserting the eyelet barrel. The prepunched hole for receiving the eyelet shall be smaller than the outside diameter of the barrel of the eyelet so that the eyelet barrel must be forced throug
38、h the hole. The eyelet shall be installed using score setting dies conforming to J.C. Rhodes part No. 1-KW-1KL and 101Y-lKlom, or Stimpson Co., part No. A2744-7 score, or equal (see 6.6). The eyelets shall be securely set in a manner that will prevent detachment from or cutting of the surrounding ma
39、terial. The scored side of the eyelet shall be on the inside of the assembly. 3.4.3 Setting of plastic fastener. Holes for assembling the fastener components shall be prepunched or predrilled and shall be smaller than the diameter of the posts of the latch and latch receptacle components so that the
40、 posts must be forced through the holes. Surfaces around the holes shall be free of uncut thread ends when prepunched and shall be free of melted residue when predrilled. The posts shall be securely set to provide a tight clinch of the assembled components. 1 3.4.4 Repairs. Repairs such as mends, da
41、rns, patches, or splices are not permitted on the canteen cover. 3.5 Marking. The identification marking shall be applied in the location shown on Drawing 2-2-280 and shall conform to type IV, class 5 of DDD-L-20. The letters “US“ shall be applied in the size characters and in the location shown on
42、Drawing 2-2-281 and shall conform to type IV, class 9 of DDD-L-20. Fastness of the class 9 marking shall be as specified for class 5 marking. 3.5.1 Instruction label. An instruction label approximately 4 5/8 inches by 3 3/8 inches shall be sewn on the inside of the flap as indicated on Drawing 2-2-2
43、81, The label shall conform to type VI, class 7 of DDD-L-20 except that the color of the label shall be medium green and shall approximate . the Cable No. 70034, 70130, or 70131 as listed in the Standard Color Reference of America. The characters used in printing the label shall be of maximum .size
44、commensurate with the area and contents specified. The legend shall be located on the label so that no part of the legend will be obscured by stitching or binding when sewn in the cover. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL -C-4 3 68
45、9C 3.5.1.1 Legend. The contents of the instruction label shall be as follows: FILLING INSTRUCTIONS Remove bladder and unscrew cap. blowing into it. Float empty bladder on side, holding neck of bladder with 1/3 to 1/2 of opening under water. totally submerge opening. Slowly submerge bladder as it fil
46、ls. If bladder collapses, remove from water allowing air to enter and proceed as above. To hasten filling, use a scooping motion with opening partially under water. Insert correct number of water purification tablets as directed on tablet bottle. Note: capacity of canteen is two quarts. To reduce sl
47、oshing noise of partially full canteen, squeeze to force water into neck and replace cap tightly. Wet the pile lining during hot weather to help keep water cool. Keep lining material dry during cold weather to provide limited protection from freezing. Fully extend bladder by Do not Carry under the p
48、arka during cold weather to keep the water from freezing. flame. Keep bladder and cover away from heat or 3.6 Workmanship. The cover shall conform to the quality of product established by this document, and the occurrence of defects shall not exceed the applicable acceptable quality levels. 4. QUALI
49、TY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the Exceptas otherwise contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. specified in the contract or purchase order, the contractor may use his own or any other facilities suitable forthe performance of the:inspection requirements specified herein, u
