1、. MIL-D-43732F 84 W 997990b 042b355 2 W MIL-D-43732F 30 March 1990 SUPERSEDING MIL-D-43732E 6 July 1987, MILITARY SPECIFICATION DRESS, WOMANS, HOSPITAL DUTY UNIFORM (HDU) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. . SCOPE - I 1.1 Scope. Th
2、is specification covers a womans dress made of twill weave, * polyester/cotton cloth, 1.2 Classification, The dress shall be of one type in the following sizes, as specified (see 6.2). Schedule of sizes X-short 6 8 10 12 14 16 Short 6 8 10 12 14 16 18 20 22 Regular 6 8 10 12 14 16 18 20 22 24 Long 6
3、 8 10 12 14 16 18 20 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the Standardization Document I
4、mprovement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-D-43732F
5、84 H 777770b 042b35b 4 MIL -a *43732F 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these
6、documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-50083 - Bag, Plastic, Folded Garment V-B-871 - Button, Sewing Hole, and-Button, Staple, (Plastic
7、) V-F-106 - Fastener, Slide, Interlocking FF-P-416 - Pin, Safety CCC-C-438 - Cloth, Buckram, Woven and Nonwoven DDD-L-20 - Label: For Clothing, Equipage, and Tentage, (General PPP-B-636 - Boxes, Shipping, Fiberboard Use) MILITARY MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence I
8、tems; Clothing, Personal Equipment and Equipage; General Specification For Polyester-Covered MIL-T-43548 - Thread, Polyester Core: Cotton-, Rayon-, or MIL-T-43624 - Thread, Polyester, Spun MIL-C-44270 - Cloth, Polyester/Cotton, For Hospital Duty Uniform (HDU) STANDARDS FEDERAL FED-STD-751 - Stitches
9、, Seams, and Stitchings MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets Attributes 2 Provided by IHSNot for ResaleNo reproduct
10、ion or networking permitted without license from IHS-,-,-MIL-D-43732F 84 7779706 0426357 b f. MIL-D-43732F (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building.4D, 700 Robbins Avenue
11、, Philadelphia, PA 19111-5094.) I 2.2 Non-Government publications. The following documents form a part of this Unless otherwise specified, the issues document to the extent specified herein. of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation.
12、 Unless otherwise specified, the issues-of documents not listed in the DODISS are the issues of the documents cited in the , solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging s (Application for copies should be addressed to
13、the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) h .- THE, COLOR ASSOCIATION OF THE UNITED STATES Standard Color Card of America Department of Defense Standard Shades Color Card for Sewing Threads (Color cards may be available from the Color Association
14、 of the United States, 343 Lexington Avenue, New York, NY 10016-0927, If color cards are not available from the Color Association, individual color samples may be obtained from the contracting activity or as directed by the contracting activity.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORIST
15、S (AATCC) Method 88B - Appearance of seam in durable press items after repeated home laundering Method 124 - Appearance of durable press fabrics after repeated home lauderings (Application for copies should be addressed to the Executive Director, Box 12215, American Association of Textile Chemists a
16、nd Colorists, P.0, Research Triangle Park, Durham, NC 27709-2215,) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.)
17、3 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _-_- MIL-D-43732F 84 m 977770b 0426358 m MIL-D-43732B 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this documen
18、t takes precedence, regulations unless a specific exemption has been obtained. Nothing in this document, however, supersedes applicable laws and 3, REQUIREMENTS 3.1 First article. When specified (see 6,2), a sample shall be subjected to first article inspection (see 6,3), in accordance with 4.3. and
19、 information to the contractor (see 6.4). Variation from this specification 3,2 Guide samples. Guide samples, when furnished, are solely for guidance may appear in the sample, in which case this specification shall govern. 3.3 Material, It is encouraged that recycled material be used when practical
20、u ae long as it meets the requirements of this specification. 3.3.1 Basic material, The basic material shall be white polyester-cotton cloth conforming to type II of MIL-C-44270, 3.3.2 Lining material. The material for lining the skirt shall be white polyester/cotton cloth conforming to type I of MI
21、L-C-44270. 3,3.3 Belt interlining. The material for interlining the belt shall be non- woven interlining cloth conforming to types I or IV, class 1 of CCC-C-438. 3,3,4 Thread, The thread for seaming, stitching, and buttonholes shall be White AH, C.A. 66050, cotton-covered or polyester-covered polyes
22、ter, ticket Nos. 50, 2, or 3 ply, and 70, 2 ply, conforming to MIL-T-43548. Spun polyester thread, ticket Nos. 50, 3 ply, and 70, 2 ply, conforming to MIL-T-43624 may be substituted for the cotton-covered polyester thread. 3,3,5 Labels, Each dress shall have an identification label and instruction l
23、abel or a combination identification and instruction label, and two size labels (one for dress and one for the belt), All labels except the belt size label shall conform to type VI of DDD-L-20, The belt size label shall conform to type IV, The fastness to laundering requirements of DDD-L-20 shall ap
24、ply. 3,3,5.1 Identification label, The identification .label shall conform to class 1. 3,3.5.2 Size labels. The size labels for the dress and belt shall conform to class 2. The size label for the dress shall include both the adjective (designating length) and numeric size. include the numeric size o
25、nly. The size label for the belt shall 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-43732F 84 m 797770b 042b357 T MIL-D-43732F 3.3.5.3 instruction label. The instruction label shall conform to class 3 and shall contain the following inform
26、ation: Washing Instructions: Machine Wash (close slide fastener) Use “Permanent Press“ cycle. warm water (100oF) and mild Laundry detergent. Use only 2/3 regular load. Use commercial fabric softener to whiten and prevent clinging. Tumble dry using “Permanent Press“ cycle (do not overload) and remove
27、 immediately from dryer. If automatic dryer is not available, shape and hang to air dry. If needed, touch up any wrinkled areas with a cool-warm iron. Wash separately from colored garments using Hand Wash detergent. Rinse thoroughly. Shape and hang to air dry. Wash separately from colored garments i
28、n warm water using mild laundry DO NOT WRING OR STARCH DO NOT REMOVE THIS LABEL DO NOT USE LIQUID CHLORINE BLEACH 3.3.5.4 Combination identification and instruction label. The identification (class 1) and instruction (class 3) labels may be combined into one label. The combination label shall confor
29、m to class 15. 3.3.6 Slide fastener. The slide fastener shall be polyester continuous monofilament (spiral or serpebtine) type I, style 3, size LS in accordance with V-F-106 requirements. The length shall be 24 inches for all sizes. The color of the tape shall be white with matching chain, slider, p
30、ull, and stops. Also, continuous chain application may be used in lieu of preassembled fasteners, provided bottom and top stops are applied. either bartack or double-sewn stitching over fastener tape turn-in. Top stops may be securely sewn using 3.3.7 Safety pins. The safety pins used for fastening
31、the buttons to the belt shall conform to class 2, size 1 of FF-P-416. 3.3.8 Snap fasteners. The snap fasteners for the front opening shall be round or square, sew-on type with rolled edges, size O, 00, or 2-0, nickel plated, brass, and shall be rust and corrosion resistant (see 4.4.1.1). 3.3.9 Butto
32、ns. The buttons for the belt shall be polyester, DOD button shade White BA, C.A. 62031, conforming to type III, class E, style 5, 22-line of V-B-871, except that shank shall protrude from back of button not less than 5 nor more than 11 lines. pull strength requirements need not apply. A plastic shan
33、k may be substituted for metal shank, and 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-43732F BL1 W 77777Ob 0426360 b MIL-D-43 732F 3.4 Design. The a bi-swing back, fly pockets with partiti a dress is a one-piece step-in style with yoked s
34、houlders and oned scissor pockets; open-necked collar; and is gathered at A separate belt with two buttonholes in front with a slide fastener fly closure; inside hanging The collar, front, and cuffs have the front yoke and around the waist seam, five rows of pintucking on outer edges. one end, has t
35、wo half dome polyester metal shanked buttons with safety pins for attaching to belt by the wearer, i i 3.5 Patterns. Standard patterns will be supplied by the Government. The standard patterns provide a seam allowance of 1/4 inch for safety stitch seams sleeve, 318 inch for cuff turn-in; 1/4 inch fo
36、r making and setting pocket welts, stitching collar ends and setting collar; making bi-swings and stitching pockets to dress. used only as a guide for cutting contractors working patterns. patterns shall be identical to the standard patterns. 1 ! except 1/2 inch for joining sides below the waist, 1/
37、2 for joining cuff to The standard patterns shall not be altered in any way and are to be The working m 3.5.1 Pattern parts. The components of the dress shall be cut from the materials specified in table i in accordance with pattern parts indicated. -. TABLE I. List of pattern parts Mat erial Nomenc
38、lature Parts Basic material (3.3 . 1) Collar Cuff Front bodice Yoke Center back bodice Side back bodice Side body bi-swing Sleeve bi-swing Sleeve Right center front skirt Left center front skirt Side front skirt Pocket Skirt scissor pocket Center back skirt Side back skirt insignia welt Belt - i/ -
39、i/ 2 1 1 2 2 2 2 1 1 2 4 1 1 2 .2 1 y Liner material (see 3.3.2) Center front lining Center back lining 1 1 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I l l. I l l l I I I I I I I I l l I l l I I l I l l l 1 I I I I l MIL-D-43732F 4 777770b 04
40、26363 MIL-D-43732F TABLE I. List of pattern parts (contd) Mat er ia1 Nomenclature Parts Non-woven interlining Belt interlining cloth (3.3.3) Temp lates Collar marker Cuff marker 1 O O - i/ The collar and cuffs are cut from fabric prepared with pintucks (see 6.7 e.). 2/ The belt may be roll cut provi
41、ding its construction is in conformance - - with operation 5 of table II and it complies with the required finished measurements. 3.6 Seam appearance rating. After the finished dress has been washed and dried (see 4.4.4), the appearance rating of seams and stitching shall be as follows : - Area Mini
42、mum Rating, Average of 3 Observations Arm hole Collar pintucking Buttom hem Side seams Front fastener seam Sleeve cuff seam Back welt seam Back yoke 3.5 3.5 3.5 3 .O 3.0 3.0 3.0 3.0 3.7 Construction. The construction shall conform in all respects to the requirements specified in table II and herein.
43、 Figure 1 is furnished solely for guidance and information. Should variation from the written document appear in figure 1, the document shall govern. 3.7.1 Stitches, seams, and stitching. All stitches, seams, and stitching shall conform to FED-STD-751. The type of seam, stitching, and stitches per i
44、nch shall be as specified in table II. Seam allowances shall be maintained with seams sewn so that no raw edges, run-Offs, pleats, puckers, or open seams will occur (see 6.5). When two or more methods of seams or stitches are given for the same operation, any one may be used. When stitch type 401 is
45、 used, the looper (under thread) shall be on the inside of the dress. Thread tension shall be maintained so that no tight or loose tension will result (see 6.5). Overedge stitching shall be 3/16 to 1/4 inch wide. Raise stitching shall be 1/16 to 3/32 inch from the joining seam, unless otherwise spec
46、ified herein. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-43 732F a 3.7.1.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched 1/2 inch minimum except when caught in other stitching or turned under in a hem. E
47、nds of a continuous line of stitching shall be overlapped not less than 1/2 inch. loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. embedded in the materials sewn. Thread tension shall be maintained so that there will
48、 be no The lock shall be 3,7,1.1.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks, skipped stitches, run-Offs, or bobbin run-outs occur during sewing, the stitching shall be repaired by restarting the stitching a minimum of 1/2 inch behind the
49、 end of the stitching. c i/ b. Except for prestitching, thread breaks, or two or more consecutive skipped or run-off stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. minimum of 1/2 inch before the defective area and continue a minimum of 1/2 inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the d
