1、AMSC N/A Page 1 of 3 FSC 8455 INCH-POUND MIL-DTL-3628/41F 10 November 2009 SUPERSEDING MIL-DTL-3628/41E 15 November 1996 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, MARINE CORPS, PISTOL COMPETITION This specification is approved for use by all Departments and Agencies of the Department of Defen
2、se. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. MATERIALS: PENDANT: Gilding Metal DASH NO. SUSPENSION BAR: -1: Gold -1, -2: Red Brass or Gilding Metal -2: Silver -3: Gilding Metal -3: Bronze FINISH: PENDA
3、NT: -1: Hard Enameled, Gold Plated, Matte Finish, Lightly Polished Highlights and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 8. REVERSE - Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. -2: Hard Enameled, Silver Plated, Oxidized, Relieved
4、, Lightly Polished Highlights and shall match TIOH Metal Finish Chip Number 15. REVERSE - Silver Plated, Mirror-like Polished. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/41F Page 2 of 3 -3: Hard Enameled, Oxidized, Relieved, Highlig
5、hts Polished. REVERSE - Mirror-like Polished. SUSPENSION BAR: -1: Gold Plated, Matte Finish, Polished Highlights and shall match TIOH Metal Finish Chip Number 8. REVERSE - Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. -2: Silver Plated, Oxidized, Buffed Relieved,
6、 Matte Finish, Polished Highlights and shall match TIOH Metal Finish Chip Number 15. REVERSE - Silver Plated, Mirror-like Polished. -3: Oxidized, Relieved, Highlights Polished. REVERSE - Mirror-like Polished DIMENSIONS: PENDANT: DIAMETER: 1-9/32 inches (REF) THICKNESS (at rim): 0.085 inch + 0.005 in
7、ch SUSPENSION BAR: HEIGHT (overall): 3/8 inch (REF) WIDTH (overall): 1-15/32 inches (REF) THICKNESS (edge): 0.065 inch + 0.005 inch ASSEMBLED HEIGHT (overall): 1-7/8 inches NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Enameled areas shall be
8、as indicated. The color shall conform to the TIOH chip numbers listed below or the standard sample. COLOR CHIP NUMBER Black 26 White 28 3. Epoxy resin (stoning epoxy) may be used in lieu of hard enamel at the option of manufacturer. Epoxy resin shall be smooth and flush with the dikes. 4. The connec
9、ting links, fabricated from wire with a nominal diameter of 0.044 inch, shall be oblong shaped, 3/16 inch + 1/64 inch long by 1/8 inch + 1/64 inch wide. The links shall be manufactured with the same material and finish as the pendant and suspension bar. 5. The lugs are integral. 6. The attaching dev
10、ice shall be a prong and flat ball clutch type. Red brass flat ball clutches shall be used for Dash No. -1 and -3, Nickel plated flat ball clutches shall be used for Dash No. 2. The prongs shall be located on the horizontal center line on the back of the suspension bar equidistant from each end and
11、1-1/16 inches + 1/32 inch apart. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/41F Page 3 of 3 CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous is
12、sue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and re
13、lationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Marine Corps MC (Project No. 8455-2010-006) Review activities: DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
