1、MIL-HDBK-LL3C 91 m 9999970 000b098 O MIGHDBK-113C SUPElEGSEDING MIGHDBK-113B 28 February 1985 24 h, Develoyxllent-; and IQqineering Center, ATIN: STRREJISE Ipapowement Pmposal (M Form 1426) awing at the end of this document or by letter. 0 Fbrk Eelvoir, 22060-5606 by using the self-addressed Standar
2、dization Document P i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MILrHD3K-113C cn?rENm Pm cz-QwmR I . SooPE . 1 CHAETER II . GENERAL z4PPumm. lYcMrEmNs. AND FEDERAL SmCK cxAssIl?IcATIoN 1 . 2-1 2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.1.7 2.1.8 2
3、.1.9 . 2.1.10 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 2.2.8 -2.2.9 mw mm AND GEAR OILS 1 Tactical sewice 1 MIGG2105. rubricatm Oil. Gear. Multigmpose . 2 MuiG2104. rubricating oil. Intemal Carbustion Ehgine. MIGL-6082. rubricating Oil. Aimraft MIGe7808. rubricating Oil. Aircraft Turbine “7870.
4、 Iubricating Oil. General Furpose. MIGk9000. rubricat- Oil. shima.xd Interml MIGG21260. rubricating 011. Internal Conkustion MIGG23699. rubricating Oil. Aircraft. Missile. and ordnanae . 7 MIGH-6083. Hpkaulic Fluid. Petroleum Base for Presewation and operation 7 MIGH-46001. Hydraulic Fluid. Eetmleum
5、 Base. for Machine Tools . 8 MIGH-46170. Hydraulic Fluid. Rust Inhibited. Fire Resistant. Synthetic HyREASES 12 2.3.1 W-0632. Grease. .Industrid. General Purpose 12 2.3.2 W-0671. Grease. Graphite 12 2.3.3 W-0679. Grease. Railway 12 2.3.4 MILE Table x . Base stock Viscosities . 81 Table XI . Cmpsitic
6、n and Praperties of Finished Oil 81 Table XII . viscosity properties of synthetic %ine Oils . 82 Table XII1 . Summary of Ehgine Oil Test Fmo Engine oil performance and haw it is masumd . 84 20 . Cmnkrcial engine oil perforiam=e classification . 85 30 . Kerformamx Definitions of military -if ication
7、of engine oils 94 mix C Viscosity Measurement and Classification of Gear Lubricants 10 . Viscosity and haw it is meamxed . 97 20 . Viscosity classification of gw oil 97 V Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-LL3C 71 7777770 OOObLO
8、Lt 2 W CONlWE (contd) AppENDIcIEs Z$pxkkh D Brfomance Meammw. whem applicable, and material statemmts aollsidered to be beneficial to field personnel. Various tables and figures list or show specific -ts aad chamcteristics of a nmker of the more important lubricants and cmpmnds. Qlapters on a%mduct
9、melf Life and Retest Frequenciesaa and alproduct Utations and CxiWria for Tenprature mlicationsaa have been included to assure a proper qitality surveillance and to assess a satisfactory operation under lm taperature applkatiorts. -ces contain viscosity and perfom meafllrement and classification ins
10、tructions and preparation p- for solid film lubricant specifications. (a). A list of important properties with typical values are given in Table I. 2.1.1 MIGG2104, rubricatina Oil, Intemal cepnbustion Edne,Tactical Semice. (a) Intended use: The engine oils merd by this specification are intended for
11、 the crankcase lubrication of reciprocating spark-ignition (gasoline) and compression-ignition (diesel) engines used in all types of military tactical equipment, hluding electric generators, qi/constmction; and material hanluing equipment and for the crankcase lubrication of high-speed, high output,
12、 supeq/turkahqed diesel engines used in cd1 ground equipnent at agents., amion inhibitors, anti-stain aqents, anti-chatter aaaitives, ant- foam aga*, pour point depressants, etc.) as are necessary to meet specified requirements. No constituent base stock materials considered to be carcinogenic as de
13、fined under Hazard ccHmra;mication Standard (HE) 29 CFR 1910.2100 shall be used. See EEtHTP313 for-additional infomtion. (b) Limitations: This .oil shall not be used for autam0t;ive applications. !this is a.mn detergent oil. See appxdix G. (c) -stock numbrs: Refer b-appendix F ,for stwk numbers. (d)
14、 Constituent niterials: The lubricating oil Ml be a refinea ptrolek pmduct and may contain approved pour point depressants in the maxinnrm amount of 1 percent by weiw. Additives other than pour point depressant, shall not be used. - _. 2 a c a . a Provided by IHSNot for ResaleNo reproduction or netw
15、orking permitted without license from IHS-,-,-O 2.1.4 MIGG7808, rubricatins Oil, Aircraft Turbine Engh, SVnthetiC Base. . i (a) nttended use: lubricant is intmded for use in specific models of aircraft turbine engines, helicopter transmissions, accessory and auxiliary pent, auxiliary pwer units and
16、other types of pent wing a synthetic base oil. Also the lubricating oil is used for engine lubrication of specific gas turbh pawered ground equipnent. It is intmded for tmperatures abcnre -54 % (-65 9) . (b) Limitations: mis oil is not suitable for autoanotive applications other than as stated me. (
17、c) Stock numbers: Refer to appendix F for stock n-. (d) constituents materials: ?he aamposition of this lubricating oil is not c limited except that organormetallic of titanium and silicone antifoam agents are prohibited. If the lubricating oil contains a tricresyl phosphate additive, not more than
18、one percent of the tricresyl phoqhate shall be ortho isomer. For limits in trace element content, refer to the specification. 2.1.5 MIGG7870. rubrkatins Oil, General punxse. Lm Temerature. (a) Intended use: The oil covered by this specification is intended for use wherever a general pupse, law tempe
19、rature, lubricating oil is required. It is specially designe3 for use where an oil of law evaporation, possessing rust pttive praperties is desired. (b) Limitations: Not to be used in engine applications. This is a law detergent oil. See G. (c) Stock numbers: Refer to Apjpdx F-for stock nm. (d) cons
20、tituent-materials: The oil shall be of a fraction of petroleum refined to meet the requirements of the specification, and containing additive . materials to impart corrosion protection and oxidation resistance properties. 2.1.6 MIL.ammercial type vehicles used for addnhtrative (post, camp, .and stat
21、ion) se.rvice typical of, (1) gasoline engines in passenger cars and light to medium duty trucks. aperating under marmfadurer warranties, and (2) lightly super/tmbockqed diesel engines aperated in -te duty. Ihe oils are intended for use, as defined by manufacturers, in meeting service classification
22、s !X and =,when tenperatums are abme -35 % (-31 ?F). (b) Limitations: The oils ccwered by this specification are not intended for use in high-outpt diesel engines and, as su Aircraft. Missile, and ordnam=e. (a) Intended use: Tfie primary intended use of this fluid is in aircraft applications such as
23、 autamatic pilots, shock absmkrs, brakes, flap control mechanisms, missile hydraulic servo-amtrolled system, and other hydraulic systems using synthetic sealing material. This fluid has limited use in ground for identification purposes. The recQBmnended operating taperature ranges are clased system.
24、 For Sealed system pressurized with inert gas, a maximum operating oil tenperatwe of 260 % (500 9) can be tolerated for short pericds (not to exceed 15 min.). 1 equipent since it does not pravide for rust protection. This oil is dyed red -54 tQ 71 % (-65 to 160 ?F) in open. systems and -54 to 135 %
25、(-65 to 275 9) in (b) Limitations: This material has a rather high rate of evaporation and should not be used as a general pqme high temperature hydraulic fluid. Shipnent and storage of systems filled with this fluid require drain and refill. with MIGH-6083, Hydraulic Fluid, petroleum Base, for pres
26、ewation and testing. This fluid is not interchaqeable with any other type or grade of hydraulic fluid. The flash point of this product could be belm 100 %. (c) Stock numbers: Refer to appendix F for stock numbers. (d) - Constituent materials: This hydraulic fluid consists of light petroleum fraction
27、s, a viscosity index inpmver, an oxidation inhibitor, and anti-war agents. 2.2.2 MIGH-6083, Hvdraulic Fluid, Petrolebn Base for presewation and oceration. (a) Intended use: The primary interded uses of this fluid are, (1) as an operation and preservative hydraulic fluid in ground pent such as in rec
28、oil mechanisms and other CCBnbat and canbat support rade1 .28.8-35.2 cSt at 40 % (104 %) Grade2 41.4-50.6 cSt at 40 % (104 OF) Grade3 61.2-74.8 cst at 40 % (104 9) Grade4 165 to - -Ost at 40 % (104 9) Ihe selection of hydraulic fluids Sh0uld.k based on the mmmendation of the equi- manufacturer. Ihes
29、e hydraulic fluids may also be used in applications requhing corrosion inhibited and oxidation resistant lubricating oils. Grades 1, 2 and 3 possess good anti-wear properties. (b) Limitations: These fluids are not inbmhangeable with each other. Grade 4 Md not be used where anti- praperties are criti
30、cal. (c) Stock numbers: -fer to appendix F for current stock numbers. (d) Qonstituent materials: This hydraulic fluid wnsists of a refinea petroleum oil, with additives as necessary. No constituent base stack materials midered to be CarCiTlogenic as defined under Hazard Ccmunication Standarrl. (W) 2
31、9 CFR 1910.1200 shall be used. See FED-SIW313 for additional infomation. 2.2.4 MIGH-46170, Hvdraulic Fluid, Rust Inhibited, Fire Resistant, Synthetic HMmmrbon Base. (a) Intended use: Type one is intended for use in recoil mechanisms and battle tank turret hydraulic system. This fluid has superior fi
32、re resistant characteristics CcBnpared to MIGH-6083 fluids and has been evaluated and found satisfactory for use in the M-W/M-48 series tank. If used in other CcBnbat vehicles, a study should be made to determine its applicability, particularly in the area of seal aapkibility and law tempera tu oper
33、ability in such system. Since this fluid is rust inhibited, it may be used as a presewative medium for hydraulic systems and CcBnpOnents. Type two is a preservative fluid for aircraft hydraulic systems and CcBllpOnents. This fluid is dyed red for identification plqmses. See appxdix H for vehicle CCB
34、nponent application. (b) Limitations: For retrofit of hydraulic system containing MIGH-6083, draining of MIGH-6083 should be as -coqlete as possible. contamination of MIGH-46170 with MIGH-6083 or MIGH-5606 seriously affects the fire resistant characteristics of this fluid. ?his fluid cannot be used
35、in self-propelled artillery due to its viscosity at -54 % (-65 9). Refer to am F for C-JUrrent Stock numbers. (d) Constituent mterials: This fluid consists of a synthetic hydrocarbon (aim olefin polymer) base stock and additives to meet the technical requirements of the finished pmduct. 8 Provided b
36、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-3.33C 93 W 7979970 0006333 3 M MIGHDEK-113C 2.2.5 MIGB-46176. Brake Fluid, Silicone, AutamOtive. All Weather. ODeratioml and -tive. (a) Interded use: This fluid is intended for use as an owrational and p
37、resewativefluid in autamotive hydraulic brake systems at -; 1/ 82 YR o. 20 ?ass 65 lone 65 lone - 65 done I o, O00 I o, O00 250 50 10 MIL-H-46170 13,000 2,600 19.5 3.4 2.1 Il NR NR 0.85 200,000 Pass Pass Pass 5308 at 121 “C 15-25 0.05 TYP 11 dved red Pass NR 0.30 O .60 NR Pass 5.0 X (149 OC, 22 hrs)
38、 NR NR Pass NR -54 343 118 (type I) 104 (type II) 246 0.20 NR 65 None 65 Nm 65 None 10,000 10,000 250 50 10 MIL-H-83282 10,250 2,200 14.0 3.5 1.0 2.0 Il 0.82 1 NR 200,000 NF! Fail, NR Pass 5308 at 135 OC 18-30 0.01 Dyed red Pass 0.21 0.30 0.60 NR NR 20.0 X (205 oc, 6.5 hrs) Pass NR Pass 70 345 -55 2
39、05 245 0.10 NR 65 Nok UR NR NR NR IO, wo 1,000 150 20 5 MIL-H-46001 1234 NR - NR 28.8 41.4 135 165 35.2 50.6 61.2 74.8 NR - NR . 90- NR - -. 0.87 0.88 0.88 0.88 Pass a- Pass NR - NR - 2.0 3.0 3.0 5.0 NR - NR - NR - NR NR - 50 50 50 NR NR - NR NR - NR - NR -12 -12 -12 -6 NR - 188 1% 1% 221 216 218 21
40、8 246 1.5 1.5 1.5 0.20 NR - NR - 100 -. 25 NR - NR - 100 NR - 2/ Only for 24 hrs with trubine rust test 3 Cincinnati Milacrom, Procehre A - Test 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIGHDK-113C (a) A list of important properties with ty
41、pical values are given in Table III . 2.3.1 W-Gd32. .Grease. Industrial, Gemmi Flumose. (a) use: Operating temperaeureS for each of 3 grades are as (O to 130 OF), and Grade 3: -12 to 60 % (10 to 140 9). All three grades are for use in applications calling for the respective grade of grease, which ar
42、e usually sliding metal on metal envirommts. foil-: 1: -23 49 Oc (-10 to 120 OF), Grade 2: -18 54 Oc (b) Limitations: None of the three. grades are inhibited against oxidation or corrosion under adverse conditions. grease shdd not be used .in place of MIGo10924, Grease, Autamotive and Artillery. Cau
43、tion is advised in -,hg this grease in nonspecified applications. (c) Stock rnrmbers: Refer to appendix F for stock nmbers. (d) cbnstituent materials: The grease is a mineral lubricating oil base, thickened with a calcium soap of one or mom of the higher fatty acids, with or without additives. No co
44、nstituent base stock materials considered to be carcincgenic as .defined under Hazard ccpnmunication standard (Ha) 29 CER 1910.1200 shall be used. See FED”313 for additional infonnation. 2.3.2 W-0671. Grease; Gramite. (a) Intended use: Operating temperatures for each of 3 grades are as follows: Grad
45、e 1: -23 to 49 % (-10 to 120 9) , Grade 2: -18 to 54 (O to 130 OF), and Grade 3: -12 to 60 % (10 to 140 9). All 3 grades are for use h” applications calling for graphite grease of the consistency specified. for the respective grades. (b) Limitations: The Ussentially, but not limited to, gelling agen
46、t and a suitable liquid lubricant. , 2.3.5 MIL, achatar screws and other equipment requiring a lubricant with high load carrying capacity over a temperature range of -73 to 121 OC. (b) Limitations: Caution is advised when using this grease in mnspecified applications. (c) Stmk nunbrs: Refer to am F
47、for stock numbers. (d) Constituent materials: Ihe grease shall consist essentially of a gelling agent, a law. tempratme liquid lubricant, and an extreme-pressure additive and any other chemical addition agent required to meet the requirements of this specification. Ihe -ition of the lubricant is not
48、 otherwise limited but substantial proportions of non-petroleum materials will be required to meet the volatility and lm temperature requirements of this specification. 2.3.11 MIL: None given. (d) Constituent material: Synthetic base oil with or without additives as mcssary to meet specification. No
49、 aonstituent base St0c;k materials conkidered to be carcinogenic as defined under Hazard ccamrmnication Standard (HCS) 29 CFR 1910.1200 shall be used. See FED-STD-313 for additional information. O 2.3.15 MI-46886, Grease, Silicone. (a) Intended use: grades, %ightI1 and “ediun1 consistency, are described by the specification document and to be used as lubricants. (b) Limitations: This grease is limited to uses where a nonhydmcarhn lubricant of either %ightI1 or
