1、MASK, GAS, MIL-M-10563A 7 AUGUST 1951 - SUPERSEDING MILM-l0563(Cml C) 28 September 1950 MILITARY SPECIFICATION SPECIAL, M2A2-AMMONIA .M24VA1 This specification was approved by the Departments of the Army, the Navy, and the Air Force foi. use of procurement services of the respective Departments. 1.
2、SCOPE 1.1 This specification covers one type of mask for use against ammonia vapors. 2. APPLICABLE SPECIFICATIONS, OTHER PUBLICATIONS, AND DRAW- INGS 2.1 Specifications.-The following specifi- cations and the specifications listed on the referenced drawings, of the issue in effect on date of invitat
3、ion for bids, form a part of this specification : U. S. ARMY SPECIFICATION 94-40645-Marking, Exterior, -Domestic and Export Shipment, by Contractors. NAVY DEPARTMENT SPECIFICATION General Specifications for Inspection of Material. (Amy.-Copies of specifications may be obtained from the procuring age
4、ncy or as directed by that agency. Both the title and identifying number or symbol should be stipulated when requesting copies.) (Navy.-Copies of Military and Navy Department specifications may be obtained upon application to the Bureau of Supplies and Accounts, Navy Department, Washington 26, D. C.
5、, except that activities of the Armed Forces should make application to the Com- manding Officer, Naval Supply Depot, Scotia 2, N. Y. Both the title and identifying number or symbol should be stipulated when requesting copies.) (A.ir Force.-Copies of Military and U. S. Army specifications may be obt
6、ained upon application to the Commanding General, Air Development Force, Wright-Patterson Air Force Base, Dayton, Ohio. Both the title and identifying number or symbol should be stipulated when requesting copies.) 7, 2.2 Other publications. - The following publications, of the issue in effect on dat
7、e of invitation for bids, form a part of this speci- fication : BUREAU OF SUPPLIES AND ACCOUNTS PUB- LICATION Navy Shipment Marking Handbook. (Copies of the Navy Shipment Marking Hand- book may be obtained upon application to the Bureau of Supplies and Accounts, Navy Department, Wash- ington 26, D.
8、C., except that activities of the Armed Forces should make application to the Commanding Officer, Naval Supply Depot, Scotia 2, N. Y.) MILITARY STANDARD MIGSTD-105 - Sampling Procedures and Tables for Inspection by Attri- butes. (Copies of Military standards may be obtained 2.3 Drawings.-The followi
9、ng drawings of the issue in effect on date of invitation for bids, form a part of this specification: from the same source as the specifications.) CHEMICAL CORPS DRAWINGS B5-1-182-Mask, Gas, Special, M2AZ Ammonia MZ-IVA1-Bill of Material. C5-20-22-Packing, Gas Mask-Assem- bly, Packing Diagram, and B
10、ill of Material. 9. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-10563A (Copies of Chemical Corps drawings may be ob- fained from the Chief Chemical Officer, Industrial Division, Field Office, Army Chemical Center, Md. Attention : Drawing an
11、d Specification Section. Both the title and identifying number or symbol should be stipulated when requesting copies.) 3. REQUIREMENTS 3.1 Components.-All components used in the assembly of the mask shall conform to the specifications and drawings forming a part of this specification. 3.2 Assembly.
12、- The mask shall be as- sembled as specified on Drawing B5-1-183 which is listed on Drawing B5-1-182. 3.3 Workmanship.-All work shall be done in a neat and workmanlike manner. . 4. SAMPLING, INSPECTION, AND TEST PRQCEDURES 4.1 Lot.-A lot shall consist of the masks produced by one contractor, from th
13、e same materials, and under essentially the same manufacturing conditions. However, not more than one lot of canisters, hoses, and facepieces shall be represented in any one lot of finished masks. The inspection lot for nondestructive inspection, within the above limitations, shall be designated by
14、the in- spector. 4.2 Sampling for nondestructive inspec- tion.-Sampling for nondestructive inspec- tion shall be conducted in accordance with the authorized classification of defects (see 4.3.4) and Standard MIL-STD-105 (see 6.2). 4.3 Inspection. 4.3.1 Components.-The inspector shall as- certain tha
15、t, prior to assembly, all compo- nents or subassemblies of the mask procured under separate specifications or drawings have been inspected, tested, and accepted in accordance with their respective specifica- tions or drawings, 4.3.2 Packaging, packing, and marking.- The inspector shall inspect the p
16、ackaging, packing, and marking of the masks for com- pliance with section 5. . 4.3.3 Procedures.-For Naval purchases, general inspection procedures shall be in ac- cordance with General Specifications for In- spection of Material. 4.3.4 Classification of clef ects.-Inspection of the mask shall be co
17、nducted as follows: 4.3.4.1 Assembly (after assembly of hose to facepiece and canister). - (Dwg. B5-1-183 which is listed on Dwg. B5-1-182.) Categories and defects of impecthn Gage OT othm method Special AQL 0.036 percent A. Assembly of hose to facepiece, B. Assembly of hose to canister, improper _V
18、isual and manual improper _Visual and manual Major AQL 1.0 percent 1. Facepiece (lens, valve, faceblank), damaged _Visual 2. Hose, damaged _-_-_Visual 3. Canister, damaged _Visual 4. Rust _-_Visual 6. Hose fastening assembly, damaged-Visual 6. Mask, contaminated _-_Visual A ri Minor AQL 2.6 percent
19、61. Mask, improperly arranged in carrier _Visual 62. Antidim set, missing _-Visual 63. Carrier, damaged or nonfunctioning_Visual and manual 64. Faceform, missing _Visual Incidental None. 5. PREPARATION FOR DELIVERY 5.1 Packaging.-Each mask shall be pack- - aged and marked for shipment as specified o
20、n Drawing B5-20-23 which is listed on Drawing C5-20-22. 5.2 Packing. - The packaged masks (see 6.1) shall be packed for shipment as speci- fied on Drawing C5-20-22. 2 _ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-., *- MIL-M-LO563A 42 3999906 023
21、3837 9 W MIGM-10563A 5.3 Marking. - All shipping containers shall be marked in accordance with Drawing B5-12406 which is listed on Drawing B5- 1-182. In addition to any special marking re- quired by the contract or order, all shipping containers for the Air Force shall be marked in accordance with S
22、pecification 94-40645 and for the Naw. in accordance with the Navy Shipment Marking Handbook. 6. NOTES 6.1 Ordering data. - Procurement docu- ments should specify the title, number, and date of this specification. 6.2 Inspection.-Inspection will not neces- sarily include all drawing and specificatio
23、n requirements ; however, the omission of in- spection does not constitute a waiver of these requirements. 6.3 Stock number. - The Chemical Corps stock number for this item is 510941. Notice.-When Government drawings, specifica- tions, or other data are used for any purpose other than in connection
24、with a definitely related Govern- ment procurement operation, the United States Gov- ernment thereby incurs no responsibility nor any obligation whatsoever; and the fact that the Govern- ment may have formulated, furnished, or in any way supplied the said drawings, specifications, or other data is n
25、ot to be regarded by implication or otherwise as in any manner licensing the holder or any other person or corporation, or conveying any rights or permission to manufacture, use, or sell any patented invention that may in any way be related thereto. Custodian: Army-Chemical Corps Other interest: Army-MT Nav y-MCY Air Force. 3 * U, I. QOVLRNWENT ?RINTINa OPCICLI 1911 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
