1、s- 37-03 5. MIL-M-70765 13 H 7779706 0357370 3 _ MIL-M-70765 (AR) 10 JULY 1988 MILITARY SPECIFICATION MINE ANTI-PERSONNEL, M86 , SPECIAL TEST MINE LOADING AND ASSEMBLY OF This Specificatj-on is approved for use within the U.S. Army Armamerit Munitions and Chemical Command, and is available for use b
2、y all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 =ye. This specification covers the loading, assembling and packing of the Special Test Mine (ST?I)/ for the Mine, Anti-p$rsonnel M86 assembly of the munition contained therein. 2. APPLICABLE DOCUMENTS 2.1 Government documents.
3、 - 2.1.1 *cifications and standards. The following specifications and standards Form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall Se those listed in the issue of the Department of Defense Index of Specifications and Stan
4、dards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification For MIL-B-70731 - Battery, Primary, Reserve Ammonia, 8 Milliompere Hour Capacity for Mine Anti-Personnel M86 For Transfer L
5、ead Assembly MIL-$1- 7 O 7 8 O MIL -M- 7 O 7 7 7 - Munition for Mine, Anti-Personnel, M8 MIL -14- 4 8 2 4 5 - Molding Compound, Housing and Flug MIL-B-70776 - Bandoleer, M86 Mine - Mine, Anti-Personnel, M86 Arming Assembly Beneficial comments (recommendations, additions, deletions) and any pertinent
6、 data which may be of use in Impraving this document should be addressed to: Commander, U.S. Army Armament,Munitions and Chemical Command, Attn. AMSMC-QA, Picatinny Arsenal, New Jersey 07806-5000 by using the self-addressed Standardiza- tion Document Improvement Proposal (DD Form 1426) appearing Et
7、the end of this document or by. letter, I AMSC N/A FSC 1345 DISTRIBTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINSG PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-70765 33 m 4499906 03573
8、73 5 m c .I MIL-M-70765 (AR) MI L -M- 7 O 7 7 8 - Munition for Mine, Anti-Personnel, M86 MIL -M- 7 O 6 9 7 - Mine, Anti-Personnel, N86 Molded Assembly Acceptor Lead Assembly Por For STANDARDS MI I; 1 TARY NIL-STD-105 - Sampling Procedures and Tables for NIL-STD-286 - Propellants, Solid: Sampling, In
9、spection by Attributes Examination and Testing 2.1.2 Other Government documents drawings and eublications. _.I_-._I-yl-l-I.-l_- L .-II.- L -.-I -.-_- The folowinq other Government documents, drawinq:;, . and publications-form a part of this specification to iiie extent specified herein. Unless other
10、wise specified, the issues shall $e those in effect on Lhe date of solicitation. D2IAWINGS (See 6.7) J. S. ARMY ARMAMENT, RESEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) 12579595 - Arming Assembly, PDM 9 3 6 6 6 6 1 - Nolded Assembly, PDM 9366705 - Special Test Mine, (STM) for Pursuit 9366710 -
11、 Packing and Marking for Box, Wirebound for De te r rent Mun i t i on Mine APEXS (PDN), M86 or Classroom Model M86 APERS Mine 12910122 - Special Test Mine with Bandoleer for (Copies of specifications, standards, handbooks, drawings, publications, and other Government documentis required by contracto
12、rs in connection with specific acquisition functions should be obtained Lrom the contracting activity or as directed by the contracting activity *) 2.2 -. Other -.- .-c- oublications. -.- -.- - The following document(s) form a part: of this specification to the extent specified herein. Unless otherw
13、ise specified, the issues of the documents which are DOD adogted shall be those listed in thz issue of the DOISS specified in the solicitation. Unless otherwise specified, the issues of docume:its whicli is current ii the date of the solicitation. AMERICAN SOCIETY OF TESTING AND MATERIALS (ASTM) AST
14、M-D- 6 9 5 - Compressive Properties of Rigid Plastics. (Application for copies should be addressed to: ArneLicari Society for Testincj and Materials, 1916 Race Street, Philadelphia, PA 14103. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I T MIL-
15、M-70765 13 7799706 0357372 7 M MIE-M-7 O 7 6 5 (AR) 2.3 Order of precedence. In the event of a conflict between -.I_ the text of this specification and the references cited herein. a (except for associated detail specifications, specification shhets or MS standards) the text of this specification sh
16、all take precedence. Nothlng in this specification, however shall supersede applicable laws and regulation unless specific exemption has been obtained, 3 . mQUlREMENTS 3.1 Material. Materials shall be in accordance with the ap2licable drawrcgs and spzcif ications, 3.2 Components -_-.-_I and assembli
17、es. 3.2.1 Mine. The Special Test Mine (STM) shall comgly with all requirements specified on Drawing (Dwg. 9366705 and 9366661) all associated drawings and with all requfrements specified in applicable speciZications. 3.2.2 Munition. The inert munition and components shall comply with all reyuiresent
18、s specified on Dwg. 9398449, all associated drawings and with all requirements specified in applicable spec i f ica t ions including MIL-B-7 07 3 1, MIL-M-7 07 80, MIL-M-70777, MIL-S-70776, MIL-M-70778 and MIL-M-60697. - 3.3 Functioning. 3.3.1 Arming. There shall be no arming of the ShA, firing of t
19、he piston actuator or the gas generator prior to 25 seconds after depressing the battery ball. 3.3.2 Safe dud. The mine, if not functioned by any external - or internal mode, shall not function after the maximum self destruct time lias elapsed. 3.3.3 - Hazardous dad. All safe duds when tested as spe
20、cified in 4.5.5.1, shall not be capable of functioning after the inaxiinuin self destruct tine has elapsed. 3.3.4 _-.I_- Anti-disturbance functioninq. - The mine shall function in the anti-disturbance mode as the mine is disturbed by two (2) different movements to two (2) different sides. 3.3.5 Brea
21、kwire functioninq. The mine shall functign in the -.-I breakwire mode when any deployed tripline is puiled with a minimum force of one hundred and forty grams (140 g) to rnax force of six hundred grams (600 4). 3.3.6 Self-destruct functioning. The mine shall be capable of self-destructing itself wit
22、hin the self-destruct minus 20% OE time limit. 1) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-fl-707b5 13 999990b 0357373 7 a- f c MIL-M-70765 (AR) 3.3.7 _.- Early functioning. The mine shall not self-destruct itself by any internal mode w
23、ithin 80% of the self-destruct tine. 3.3.8 Tripline - dxloyment. The mine after ground impact and with unobstructed field; shall deploy a minimum of three (3) triplines with at least one (1) deployed tripline attaining a minimum of deployed length of thread of ten (10) feet and two (2) others provid
24、ing additional length to total. sixteen (16) feet for three (3) triplines. 3.4 Documentation of plan for safety in handlinq-of munitions. Prior to loading, the conkractor shall document a dtailed plan of the procedures to be employed during handling of the munition. This documentation shall describe
25、, as a minimum, the procedure:; to be employed to assare that: 1. The shorting bar is not deEormed or broken. 2. The battery is not activated. 3. The two munition models remain segregated at al1 times. 4. The exterior model markings on each mine are consistent with the munitions it contains. -0 5. T
26、he temperature o the molded assemblies, or the munition does not exceed 1650F at my time during processing or s tor aye. 6, The temporary safety pin is present. 7. The mounting plate insulator is properly installed. 8. The special test mines shall always be marked and segregated from the other munit
27、ion models. The plan shall be submitted to the address specified in 6.7 for approval. Approval shall be received prior to any loading. Any changes to the approved plan shall be submitted for approval prior to implementation. 3.4.1 Documentation of controls for use of adhesives and sealants, The cont
28、ractor shal develop a documented operational procedure for utilization of adhesives and sealants. This procedure shall provide for control of the materials and processes to be used; iricluding controls for the following: shelf life, handling, mixing, curing and pot life. Necessary cleaning agents, s
29、afety precautions, ventilation, and any other information considered necessary for the proper use of the adhesive(s) or sealant(s) shall also be included. The procedure.shal1 be updated whznevera change is made to the process such that product quaity may be affected. I- 4 Provided by IHSNot for Resa
30、leNo reproduction or networking permitted without license from IHS-,-,- MIL-M-70765 13 H 9999906 0357374 O m MIL-M-7 07 65 (AR) P 3.4.2 Documentation of glan for molding and cure process .- - - controls. - The contractor shall prepare a written plan to be implemented for control of the process for m
31、olding the kill mechanism and overlay assembly into the housing, timing, and fuzing. The plan shall breifly describe the entire process and shall fully document the controls to be implemented for maintaining the process. The controls shall include, as a minimum, all the checkpoints referenced in 6.4
32、. Submission of this plan shall be in accordance with Data Item Description. Approval of the plan shall be limited to the controls to be employed and not the overall potting process, nor shall such approval relieve the contractor, in any way, of the responsibility for producing acceptable product. 3
33、.5 Compressive strenAth of molding comnound. The molding compound for assembling the plug to the hgsin(3ghall comply with MIL-M-48245. The resin/hardener weight ratio shall be 2.0/1.0 + 5% (1.8/1 to 2.2/1) and the ultimate compressive strength shallbe 29,000 to 38,200 psi. -_-I _ 3.6 Temperature con
34、trol during molding and cure of munition. _I_- - -y- -.- - The munition shall not be sub2ect;ed to temperatures exceeding 165OF at any time. 3.7 _- First article inspection. This specification contains technical srovisions for first =ticle inspection. Requirements for the submission of first article
35、 samples by the contractor shall be as specified in the contract. 3.8 Workmanshk. - All parts and assemblies shall be fabricate, loaded and assembled in a thorough, workmanlike manner, They shall be free of burrs, sharp edges, cracks, dirt, grease, rust and other foreign matter that may impair prope
36、r functioning. The cleaning method used shall not be injurious to any ?art, nor shall the ?arts be contaminated by the cleaning agents. All required marking and stamping shall be neat and sharply defined. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsihilitx -A- -I-_. foc Inzection. - Unless otherwise
37、specified in the contract or purchase order, the contractor is responsible ?or the performance-of all inspection requirements as spciEied herein. Except as otherwise specified in the contract or purchase order, the contractor may utilize his own or any other facilities sutiable for the performance o
38、4 the inspection requirements specified herein, uniesc disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. a 5
39、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - -_I- MIL-M-70765 13 = 7777706 0357375 2 - MIL-M-70 76 5 (AR) 4.1.1 Res_;l?_onsibilitLfor -.- .- -I-.- comDliance. L- All items must meet all requirements of sections 3 and 5. The inspection set fort
40、h in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or cupglies submitted to the Government fo
41、r acceptance coinply with all requirements of the contract. Sampliiig in quality conformance does not authorize submission of known defective material, .either indicated or actual nor does it, commit the Government to acceptance of any defective material. 4.2 -.-_- Classification of ins_t3ections. .
42、-A- The following types of inspection shall be conducted on this item. a. First Article Inspection (see 4.3) b , Quality Conformance 1nspe.ctioii (see 4.4) 4,3.1 -,-.I_ Submission. The contracLor shall submit a first article as designated by the Contrauting Officer for evaluation in accordance with
43、provisions of 4.3.2. The first article sample shall consisi- of the following items in sample quantities as indicated. Special Test Mine Test bars Bag Assembly 9366705 12910118 12 2 12 4.3.2 Inspections _-._-I- to -.I- be performed. - See MIL-A-48078 and Table I herein, 4.3.3 Rejection. - See MIL-A-
44、48078. The first article sample shall be rejected if any mine fails to comply with any of the examinations or tests specified in this specification or any of the requirements of the applicable drawings. In addition, the first article sample shall be rejected if the mines any one of the following def
45、ects: a, Any premature arming of the S fire the detonator, piston actuator or gas generator prior to 25 seconds after depressing of the battery ball. Those units to be tested in the anti-disturbance mode shall bl tested by rolling the item from one face ta another, Units which fail to function on th
46、e Eirst attempt shall be tested in the breakwire mode. Recording equipqent may be used to determine the time of unctioning of item tested in the self-destruct tima. After the maximum time-out time has elapsed plus one hourt the impact area shall be sqarched for non-functioning munitions. Any munitio
47、n which has not functioned shall be treated as a hazardous duit until it can be determined that the item is not capable of functioning. This shall be determined as follows using suitable protection and safety precautions for personnel. handling the munitions: a. Perform visual obseivakion to assure
48、the battery ball. is depressed, th,e shorting bar is sheared and to determine if there is any evidence that the detonator has functioned. b. If it cannot be determined whether or not the detonator has funtioned, attempts shall be made to function the item by tipping about an edge, pulling all deploy
49、ed triplines. If the detonator functions at any time, the item shall be classed as a hazardous dud. c. If the item has not functioned after the above external inputs have been applied, it shall be placed in an approved explosive handling box and removed from the impact area. d. A-tei: a minimum sterilization period from
