1、MIL-S-44095A 84 m 7777706 037723q 7 MIL-S-44095A(GL) SUPERSEDING MIL-S-44095(GL) 28 December 1982 i9 April1989 MILITARY SPECIFICATION SURVIVAL KIT, INDIVIDUAL, VEST TYPE This specification is approved for use by the Natick Research, Development, and Engineering Center, Department of the Army, and is
2、 available for use by i - ail Departments and Agencies of the Department of Defense. i1 1. SCOPE 8 - 1.1 Scape. This specification covers a survival kit consisting of a vest and a number of survival aids. 1.2 Classification. The vest shall be of the following sizes (see 6.2). Small Large o 2. APPLIC
3、ABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of th
4、e Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). 5 I i E -.- I iI Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed t
5、o: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public releas
6、e; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44075A BY W 7797706 0377235 7 MIL-S-44095A(GL) SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fibkrboard MIL I TARY MIL-K-818 MIL-W-1053 MIL-B-8571 MIL-C-10436 M
7、IL-M-18371 MIL-L-35078 MIL-T-36045 MIL-S-36609 MIL-B-36964 MIL-L-38217 - Knife, Pocket, General Purpose - Whistle, Ball, Plastic - Bag, Storage, Drinking Water - Compass, Magnetic, Unmounted: Lensatic, Luminous, - Mirrors, Emergency Signaling, Mark 3 - Loads, Unit: Preparation of Semiperishable Subs
8、istence 5 Degree and 20-MIL Items; Clothing, Personal Equipment and Equipage; General Specification For 42 Inches - Tourniquet, Nonpneumatic, Camouflaged, l-l/2 by - Survival Kit, Individual, Tropical, Tactical Air Crew - Blanket, Combat, Casualty Lightweight, Waterproof, Aluminized Plastic - Light,
9、 Marker, Distress STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads by Attributes (Unless otherwise indicated, copies of federal and m
10、ilitary specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publicati
11、ons form a part of this document to the extent specified herein. Un1es.s otherwise specified, the issues are those cited in the solicitation. 2 t w Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND E
12、NGINEERING CENTER 11-1-1783 11-1-2838 11-1-2899 11-1-2900 11- 1-290 1 11-1-2902 11-1-2903 11-1-2904 1 1- 1-3 173 11- 1-3 174 - Survival Kit, Individual; Vest Assembly - Vest, Survival Kit, Individual, Vest Type - Left Side Body Pattern Small Size - Right Side Body Pattern Small Size - Right Side Bod
13、y Pattern Large Size - Left Side Body Pattern Large Size - Pocket Patterns - Pocket and Lace Loop Patterns - Pocket-PRC-90 Radio - Survival Kit and General Purpose Pocket (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center Natick, MA 01760-5014.)
14、 2.2 Non-Government publications. The following document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the
15、issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and
16、Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from theorganizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 5 2.3 Ord
17、er of precedence. In the event of a conflict between the text of this L regulations unless a specific exemption has been obtained. document and the references cited herein, the text of this document takes precedence-. Nothing in this document, however, supersedes applicable laws and * 3. REQUIREMENT
18、S 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3 /- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-S-44075A 4 m 7779706 0377237 2 3.2 Materials. Material
19、s and components shall conform to the requirements specified herein and in the subsidiary documents applicable thereto. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3.3 Color. The color of the materials and components of t
20、he vest shall be as specified on the applicable drawing (see 6.4). 3.4 Design. The kit shall consist of a vest with pockets or compartments and the survival aids specified on Drawing 11-1-1783. 3.5 Vest construction. The vest shall be cut in accordance with the patterns specified herein and shall be
21、 constructed as specified on Drawing 11-1-2898. 3.5.1 Stitches, seams, and stitchings, Stitches, seams and stitchings used in the construction of the vest shall conform to FED-STD-751. 3.5.2 Patterns. The manufacturers working patterns shall be identical in size and shape to the appropriate ptterns
22、referenced Qn Drawings 11-1-2899 thru 11-1-2904, 11-1-3173, and 11-1-3174 which provide for seam allowance, size, shape, placement of pockets, directional lines for cutting, and notches for proper assembly of all parts. Unless otherwise specified, the patterns provide an allowance of 3/8 inch for si
23、ngle needle seams. 3.6 Workmanship. The finished vest shall conform to the quality of product established by this specification and the occurrence of defects shall not exceed the applicable.acceptable quality levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise
24、 specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitabl
25、e for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to pres
26、cribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the s
27、pecification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conf
28、ormance to the requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4 c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-
29、S-44095A BLJ 9999906 0399238 4 4.1.2 Responsibility for dimensional requirements. Unless otherwise speci- fied in the contract or purchase order, the contractor is responsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection sha
30、ll be made at any point, or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. 4.1.3 Certificates of compliance, When certificates of compliance are sub- mitted the Government reserves the right to inspect such items to determine the vaidity
31、of the certification. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. b. Quality conformance inspection (see 4.4). First article inspection (see 4.3). 4.3 First article inspection. When a first article is required (see 3.1 and 6.21, it sh
32、all be examined for the defects specified in 4.4.3 and 4.4.4. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be
33、inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.1.2 Component and material certification. The contractor shall furnish a certificate of compliance as eviden
34、ce that the fire starter supplied is the same as or equivalent to the fire starter referenced in note 9 of Drawing 11-1-1783 when the fire starter is not government furnished. 4.4.2 In-process inspection. Inspection shall be made of the following operations to establish conformance to specified requ
35、irements. Wherever nonconformance is noted, correction shall be made to the items affected, the lot in progress, and to the operation. Parts that do not match and cannot be corrected shall be removed from production. a. Visual and dimensional examination of the working patterns to determine that the
36、y conform to the government patterns in all respects (see 3.5). b. Visual and dimensional examination of the cut parts to determine that they are properly cut with respect to size and material directional requirements (warp and filling), that location marks and notches on the parts are located corre
37、ctly, and that parts containing material defects and damages have been removed. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - I MIL-S-44095A 84 W 999990b 0399239 b W MIL-S-44095A(GL) c. Inspection shall be performed for seams and stitching ope
38、rations and for any other operations or assemblies which cannot be inspected after the end item is completed. 4.4.3 End item visual examination. The end items shall be examined for the defects listed in table I. The lot size shall be expressed in units of survival kits. The sample unit shall be one
39、survival kit. The inspection level shall be II and the acceptable quality level (AQLs), expressed in terms of defects per hundred units, shall be 2.5 for major defects and 6.5 for total (major and minor combined) defects. TABLE I. End item visual defects. Classification Exami ne Defect Major Minor M
40、a ter ia 1 s Mesh net containing any cut, tear, burn or smash 101 Mesh net containing any abrasion, broken, or missing yarns resulting in a broken Mesh net containing any abrasion, broken, or missing yarns but not resulting in a Mesh net containing any mend, darn, patch Nylon cloth containing any ho
41、le except mesh opening 102 broken mesh opening 20 1 or splice 103 drill holes 1/16 inch or less, cut, tear, smash, multiple floats, missing yarns, or open places 104 or less in nylon cloth 202 Exposed drill holes 1/16 inch in diamater Tape or webbing containing any cut, hole, Tape or webbing not fir
42、mly or tightly or tear 105 woven or edges of tape or webbing frayed or scalloped 203 fastener tapes, or hook or pile fastener tapes not as specified 204 cords, seriously affecting service- abi 1 i ty 106 Color of mesh net, tape, webbing, slide Any cut, damage, kink, or knot in nylon End of nylon cor
43、ds not seared 205 Nylon cords contain core ends projecting through the core sleeve 206 * c 6 - - - I - b Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. End item visual defects. (contd) Classification Exami ne Defect Major Minor Hardware L k
44、 c c Seams and stitching Hardware not type specified Any required component improperly set or reversed, failing to serve intended purpose Hardware broken, damaged, or malformed or containing corroded areas, burrs, or sharp edges or opening freely i.e. , components of stud or socket separating when s
45、nap fasteners are snapped or unsnapped, or clinched excessively, cutting surrounding ma ter ia 1 as specified Any snap fastener omitted or not closing Any snap fastener nor properly clinched, Any lift-a-dot fastener not positioned Open seam more than 1/2 inch but not Open seam more than-1 inch Raw e
46、dges (except where required) more more than 1 inch l/ i/ than 1/4 inch but not more than 1 inch but securely caught in stitching L/ than 1 inch but securely caught in stitching i/ Any raw edge-including inside of pockets not seared or overedge stitched Not specified seam or stitch type Loose stitch
47、tension resulting in loosely exposed bobbin or top thread Tight stitch tension resulting in tightness of puckering of fabric One stitch per inch less than minimum specified Two or more stitches per inch less than minimum specified One or more stitches in excess of maximum stitches per inch specified
48、 Stitching margins not as specified Stitching ends backstitched less than 1/2 inch unless held down by other stitching or turned under in B hem Raw edges (except where required) more 7 107 108 1 o9 110 111 112 113 207 208 114 115 116 209 210 21 1 117 212 213 214 Provided by IHSNot for ResaleNo repro
49、duction or networking permitted without license from IHS-,-,-_- MIL-S-44075A 4 m 7977706 037724l1 4 m M -8-440?5. !GL) TABLE I. End item visual defects. (contd) Classification Examine Defect Major Minor Seams and stitching (cont d) Construction details Thread breaks overstitched less than Any required row of straight stitching Seam twisted or pleated Binding loosely or improperly applied, badly pleated, or ends no
