1、MIL-S-SL37LC LO m 7777706 033376Y O m 5-31-29 I uL-s- 13 7 IC ( EA) 6 May 1987 SUPERSEDING MIL-S-Si.371B (EA) 30 December i385 MILITARY SPECIFICATION SERVICE KIT, PORTABLE RIOT CONTROL AGENT DISPERSER, M254 This specification is approved for use within U.S. Army Chemical Research, Development and En
2、gineering Center, Departnent of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of service kit. 2. APPLICASLE DOCUMENTS 2.1 Government documents . 2.1.1 Specifications and standards. The following
3、 specifications and stan- dards form a part of this specification to the extent specified herein. 3nless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standarcls (DODISS) and supplement thereto , cited i
4、n the solicitation. SPECIFICATIONS FEDERAT, PPP-B- - Bag, Plastic, (Gener9l Purpose). PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-C-1120 - Cushioning Material, Uncompressed Bound Fiber, for PPP-P-291 - Paperboard, Wrapping and Cushioning. PPP-T-76 - Tape, Packaging, Paper (For Carton Sealing). Pack
5、aging. . : Beneficial comments (recommendations, additions, deletions) and any perti- : : !lent data which may be of use in improving this document should be addressed: : to: Commander, U.S, Army Chemical Research, Development and Engineering : Center, ATTN: SMCCR-SIT-S, Aberdeen Proving Ground , MD
6、 21010-5423 by using: : the self-addressed Standardization Document Improvement Proposal (DD Form : : 1426) appearing at the end of this document or by letter. FSC i040 * AMsc DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. I I , Provided by IHSNot for ResaleNo repr
7、oduction or networking permitted without license from IHS-,-,-MIL-S-5 i371c( EA) MILITARY MIL-p-1 i6 - Preservation, Methods of. MIL-B-117 - Bags, Sleeves and Tubing - Interior Packaging. MIL-C-5501/7 - Caps and Plugs, Protective, Dust and Moisture Seal (Cap- Plug , General Purpose) . STANDARDS MILI
8、TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attribut es. MILSTD-129 - Marking for Shisment and Storage. MIL-STD-1168 - Ammunition Lot Numbering. 2.1.2 Drawings. The following drawings form a part of this specification to the extent specified herein. Unless otherwise specified
9、, the issues shall be those in effect on the date of the solicitation. DRAWINGS U.S. ARMY CHEMICAL RESEARCH , DEVELOPMENT AND ENGINEERING CENTER 116-3-104 - Service Kit, Portable Riot Control Agent Disperser; M254. 150-1-1 - Coupling Half, Quick Disconnect, Nipple, Type I - Plain, Size 4, 1/4 Non. T
10、ube O.D. (Copies of specifications, standards and drawings required by contractors in connection with specific acquisition functions should be obtained from the con- tracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of
11、 this specification and the references cited herein ( except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing. in this specification, however, shall supersede applicable laws and regulations unless a specific e
12、xemption has been obtained. 3 REQUIRE24ENTS 3.1 Materials and components. 3.1.1 Materials. All materials cited on Drawing 116-3-104 or on the sub- sidiary drawings shall conform to the specifications listed thereon or to the specific characteristics set forth on the drawings. 3.1.2 Components. All c
13、omponents of the service kit shall conform to the specifications and drawings listed on Drawing 116-3-104 and subsidiary draw- ings. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- DIL-S-5137LC 10 W 777770b 0333766 4 W MIL-S-51371C( EA) 3.2 Leakag
14、e. 5: 3.2.1 In-line pressure check gauge assembly. The assembly (Drawing 116-3- 53) shall not leak when tested in accordance with 4.4.6.i(a). 3.2.2 Pressure check gauge assembly. The assembly (Drawing 116-3-62) shall not leak except that a naximum pressure drop of 100 pounds -per square inch zage (p
15、sig) in one minute is allowed Ghrough the air vent when tested in accordance with 4.4.6.i(b). 3.3 Preproduction. Prior to the start of regular production, a preproduc- tion sample of service kit components shall be produced for examination and tests in accordance with this specification. 3.4 Workman
16、ship. The service kit components shall be free from foreign matter , damage , hose irregularities , dents or abrasions that would prevent their intended use. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con- tract OF purchase order, the contrac
17、tor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements speci- fied herein, unless di
18、sapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must neet all
19、 requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assiring th
20、at all products or supplies submitted to the Government for acceptance comply with all require- nents of the contract. Sampling in quality conformance does not authorize sub- mission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective
21、 material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: 4.3 (a) Preproduction inspection (see 4.3). (b) Preproduction inspection. Quality conformance inspection ( see 4.4) . 4.3.1 Sample. A preproduction sample of five each of al, Compone
22、nts and sub- assemblies shall be manufactured using the same methods, materials, equipment, and processes as will be used during regular production. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I_ - MIL-S-SL37LC LO 7779706 03337b7 b MI MIL-S-IC
23、( EA) 4.3.2 Inspection procedure. 4.3.2.1 For examination and tests. The sample components and subassemblies shall be examined and tested in accordance with the classification of defects. 4.3.2.2 Acceptance/rejection criteria. If any assembly, components, or test specimen fails to comply with any of
24、 the applicable requirements, the preproduc- tion sample shall be rejected. The Government reserves the right to terminate inspection upon any failure of any assembly, component, or test specimen to comply with any of the requirements. 4.4 Quality conformance inspection. 4.4.1 Lotting. with bIIL-8 .
25、 Each lot shall be identified and controlled in accordance 4.4.2 Sampling for examination and nondestructive tests. Sampling shall be conducted in accordance with MIL-STD-105. 4.4.3 Inspection procedures for examination and nondestructive test. The service kit components and the level. A packaging s
26、hall be examined and tested in accordance with the classification of defects and with MIL-STD-105. 4.4.4 Critical defects. Each pressure check gauge assembly in the lot shall be inspected for the critical characteritics listed in the classification of defects . 4.4.5 Classification of defects. (a) I
27、n-line pressure check gauge assembly (Drawing 116-3-63) Cat egories Defects Acceptance standards Critical : None defined Ma j or : AQL 1.0 percent defective 101 Leakage 4.4.6.i( a) (b) Pressure check gauge assembly (Drawing 11.6-3-62). Categories Defects Acceptance standards C rit ical : 1 Leakage 4
28、.4.6.i(b) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-51371C( EA) n n Filling adapter (Drawing 116-3-94) . Categories Defects Critical: None defined Major : AQL 1.0 percent defective 101 Thread incorrect 102 Un de rcut incorrect 103 Locatio
29、n (depth) undercut incorrect Minor : AQL 4.0 percent defective 201 Knurl missing 202 Hose barb missing ( d) Adapter assembly (Drawing 116-3-47) . Categories Defects Critical : None defined Major: AQL 1.0 percent defective 101 102 103 Washer missing Internal thread incorrect External thread incorrect
30、 Minor AQL 4 . O percent defect ive 201 Knurl missing (e) Packaging (see section 5). Categories Defects Critical : Ma j or : 101 102 103 i04 105 107 106 None defined AQL 4.0 percent defective Components improperly cleaned and dried Components missing or incorrectly arranged Containers incorrect, bro
31、ken or crushed Containers closure incorrect Cushioning incorrect Straps loose or missing rrlarkinga missing, incorrect, or illegible and packaged 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-S-513ilC LO 77706 0333367 T MIL-s-LC( EA) 4.4.6 T
32、ests. Tests shall be conducted as follows: 4.4.6.1 Leakage. (a) In-line pressure check gauge assembly. The assembly shall be subjected to a minimum of 200 psig air pressure for a minimum period of one minute and observed for leakage. Check for leakage with a suitable leak detect- ing solution (see 6
33、.3). (b) Pressure check gauge assembly. The assembly shall be subjected to a minimum 2100 psig air pressure. Stabilize the pressure and “top-off“ to 2100 psig ninimum. Check for leakage with a suitable leak detecting solution. If leakage is observed through the air vent, observe the gauge for one mi
34、nute minimum and record the pressure drop (see 6.3). 5. PACKAGING 5.1 Cleaning. The components shall be cleaned, as necessary, to be free of foreign matter that would interfere with the satisfactory performance of, or cause damage to the item. Cleaning shall be in accordance with cleaning pro- cess
35、C-l and drying shall be in accordance with any of the drying procedures outlined in NIL-P-. 5.2 Preservation and unit packing. 5.2.1 Level A. Level shall be as specified (see 6*2). I 5.2.1.1 Gauge assembly, in-line pressure check, 300 psig. The gauge, cleaned in accordance with 5.1, shall have openi
36、ngs closed with plastic clo- sures conforming to MIL-C-5501/7 and then wrapped-in a piece of bound fiber cushioning material whose dimensions in inches shall be 1 by 5 by 12 and con- forming to type IV, class A of PPP-C-1120. The wrapped gauge shall then be enclosed in a fiberboard box having inside
37、 dimensions in inches of 4-1/2 by 4-1/2 by 3 length, width and depth, respectively and conforming to b76c, style RSC of PPP-B-636. The box shall be closed in accordance with method III or IV of the appendix to PPP-B-636. bag, size 8-3/4 bx 10 conforming to type II, ClassE, style 1 of MIL-B-117. The
38、box shall be free of any projections or sharp edges or points that could rupture or damage the barrier bag. Included air volume shall be kept to a practicable minimum when the bag is sealed. The closed box shall then be sealed in a barrier 5.2.1.2 Gauge assembly, pressure check, 3000 psig. The gauge
39、, cleaned in accordance with 5.1, shall have openings closed with plastic closures conform- ing to MIL-C-5501/7 and then wrapped in a piece of bound fiber cushioning material whose dimensions in inches shall be 1 by 7 by 12 and be placed in a fiberboard box 7-1/4 by 4-1/2 by 3 inches inside length,
40、widtn and depth respec- tively, conforming to W6c, style RSC of PPP-B-636. accordance with method III or IV of the appendix to PPP-B-636. shall then be sealed within a barrier bag, size 8-3/4 by 12, conforming to type The box shall be closed in The closed box k -. 6 I - Provided by IHSNot for Resale
41、No reproduction or networking permitted without license from IHS-,-,-MIL-S-5137LC LO U 999990b 0333770 b l II, class E, style 1 of MIL-B-117. sharp edges or corners that could rupture or damage the barrier bag. air volume shall be kept to a practicable minimum when the bag is sealed. The box shall b
42、e free of any projections or Incldded t Z 5.2.1.3 Dummy pack and gasket. The dmmy pack shall be a fiberboard box con- forming to style RSC, type CF, class weather-resistant, variety SW, grade W5c or 6c of PPP-11-636, having inside dimensions of i4 by 1-1/2 by 4-1/2 inches length, width and depth res
43、pectively. The box shall be closed in accordance with the appendix of ?PP-B-636 for weather-resistant boxes. ing 116-3-112), cleaned and dried in accordance with 5.1, shall be placed within a form fitting polyethylene bag which shall either be closed by heat sealing or folded and taped. The gasket (
44、Draw- The bag shall then be placed within the compart- - - ment for the pressure gauge assembly of the wood shipping container (Drawing 116-3-111) a 5.2.1.4 Agent transfer tube assembly. The tube, cleaned in accordance with 5.1, shall have the open end of P/N D150-1-11-5-1-B closed by means of closu
45、re conforming to MIL-C-5501/7. 5.2.1.5 Technical publications. Applicable technical publications shall be sealed within a polyethylene bag, size 12 by i4 inches, conforming to type II, :jtyle 1 of PPP-B-26. Included air volume shall be kept to a practicable nini- mum when bag is sealed. * 5.2.1.6 Ad
46、apter (P/N 2021-4-4s). The adapter shall be unit packed in accor- dance with method IC-1 of MIL-P-116, using cushioning conforming to PPP-P-2gl. The cirshioning shall be not larger than necessary to provide full protection to the item and shall be taped in place using PPP-T-76 tape. shall then be pl
47、aced in a polyethylene bag conforming to style 1, type 1, class C of MIL-B-117 and heat sealed. the cushioned item with a minimum of overage. The cushioned item The bag shall be of sufficient size to hold 5.2.1.7 Nipple (Drawing 150-1-1). Unit packing shall be as specified in 5.2.1.6, 5.2.i.8 Adapte
48、r assembly. The adapter assembly shall be installed on the agent transfer tube assembly and its open end closed by means of closare conforming to MIL-C-5501/7. 5.2,l.g Filter assembly. The filter assembly (Drawing 1.16-3-113) shall be placed within a form fitting polyethylene bag vhich shall either
49、be closed by heat sealing or folded and taped. The bag shall then be placed within the corn- partment for the pressure check gauge of the wood shipping container, Drawing 116-3-111 5.2.2 Level B. Unit packing shall be in accordance with 5.2.1. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-5L371C LO m 7777706 0333973 m 5.3 Packing. Level shall be as specified (s
