1、MIL-T-lt2LIOiX 23 7777706 OLI5LI304 4 MIGT-l2407X(AT) - SUPERSEDING MI L-T- 1240 7W (.AT ) 1 October 1983 MILITARY SPECIFICATION TRUCKS: PATIENT TRANSPORT, VAN CONVERSION, DIESEL OR GASOLINE ENGINE DRIVEN, 4x2 AND 4x4, MODIFIED COMMERCIAL This specification is approved for use by the US Army Tank Au
2、tomotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCDPE * 1.1 a. Thie specification covers forward control, diesel or gaaoline engine driven, four-wheel, two-wheel and four-wheel drive commercial truck(s) converted for
3、 use as 4 litter patient or 8 seated passenger patient transport vehicles. commercial items which shall be warranted by the manufacturer as specified in acquisition documents. Vehicles procured under this specification are 1.2 Model. The vehicle shall be one of the following models, as specified (se
4、e 6.2): 4x2 model - 4 wheels, 2 wheels driving 4x4 model - 4 wheels, 4 wheels driving Beneficia comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, A“N: AMSTA-UED, Warren, MI 4
5、8397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC-23101 i. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted w
6、ithout license from IHS-,-,-MI L-T- 12m7X ( AT) 2. APPLICABLE mms 2 1 Government documentar * 2*1.1 -Rsr 8- . The following specifications, standards, and handboaka Farn a part of thia specification to the extent specified herein. Unless otherwise specified, the iasuaa of theae documents ahall be th
7、oae listed in the issue o? the bpartment of Referise Index of speohficationa arid Standards (DODISS) I and aupplement thereto, cited in the solicitation (aee 6.2). SPEC1 PICATIONS FEDERAL L-C-300 - Sheeting and Tape, Reflective: Nanexposed W-B-131 - Battery, Storage: Vehiculw, Ignition, W-F-800 - Fu
8、el Oil, Diesel. km Adheeiive Backing. Lighting and Starting, MILITARY MIL-P-514 MI L-T-5624 MIL-P-18066 MI L-8-46178 MI L-T-83133 STANMRDS FEDERAL FEO-STD-297 FEPSTD-695 - Platea, Identification, Instruction and - Turbine Fuel, Aviation, Grades JF-4 and - Plywood, Ship and Boat Construction. - Brake
9、 Fluid, Silicone, Automotive All Weather I Operational and heservative. - Turbine Fuel, Aviation, Kerosene Type, Grade JP-8 (. Marking, Blank. JP-5. - Rustproofing of Commeroial (Nontactical) - Colore. Vehiclea MILITARY MI L-STD. 1223 - Nontactical Wheeled Vehiclaa Treatment I Painting, Identifica-b
10、ion Marking and Data Plate Standwds. * specifications, atandarda , and handbooka are available from the Naval Publicationa and Forms Center, Military Specificationa and Standardsr Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 18111-6994. ) (Unless otherwise indicated, copies of federal and military
11、 * 2.1.2 2 . The following other Government documents, drawings and publicationa, form a part of this specification to the extent specified herein. Unleas othewiae specified, the issues are thoae cited in the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
12、t license from IHS-,-,-MIL-T-12407X 23 U 777770b 0454306 * DEPARTMENT OF DEFENSE Department of Defense Index of Specifications and Standards (WDISS). (Copies of the DODISS are available on a yearly subscr.iption basis either from the Government PrintingOffice for hard copy, or microfiche copies are
13、available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093). DEPARTMENT OF TRANSWRTATION (DOT) Federal Motor Carrier Safety Regulations- Federal Motor Vehicle Safety Standards. * Federal Regulations, 49 CFR, and the Federal Register, an
14、d should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) (Application for copies of DoT publications should reference the Code of ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Noise Emia
15、sion Standards for Transportation Equipment - Medium Vehicle Engines. 1 and Heavy Trucks. (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Printi
16、ng Office, Washington, D.C. 20402.) * 2.2 kn - Chverment rub- . The following documents form a part of this document to the extent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not li
17、sted in the DODISS are documents cited in the solicitation (see 6.2). * Unless otherwise specified, Unless otherwise specified, the issue of the THE EUROPEAN TIRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual (Application for copies of the ETRTO publications should be addressed to the Euro
18、pean “yre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) * NORTH ATLANTIC TREATY ORGANIZATION (NATO) Allied Engineering Publication (AEP-5) Part II - NATO Standard Diesel and Spark Ignition Engines Laboratory Test, dated January 1984. (Application for copies of NATO pu
19、blications should be addressed to North Atlantic Treaty Organization, Military Agency for Standardization, 1110 Brussels, Belgium.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LE407X 23 M 479790b O454307 T W MI L-T-l24On(AT) sa, INC. 5537
20、 . - Storage Batteries (DoD adopted). J551 J588 - Turn Signal Lampa. 5589 - Turn Signal Switch. 5688 5689 CAE Standards and Recommended Practices. - Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). - Truck Ability Prediction Procedur
21、e (DoD aopted) . - Approach, Departure and Ramp Breakover Angles - Passenger Car and Light Duty Trucks. - Engine Power Test Code - Spark Ignition and Diese 1. 51349 (Application for copies of CAE publications should be addreased to CAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) STATE OF C
22、ALIFORNIA Vehicle Code of California, Section 27200. (Application for copies of State of California publications should be addressed to the Department of Motor Vehicles, 2570 24th Street, Sacramento, CA 95809.) THE TIRE AND RIM ASSOCIATION, INC. (Application for copies of Tire and Rim Association pu
23、blications should be addressed to the Tire and Rim Association, Inc., 175 Montrose West Ave., Copley, OH 44321.) Year Book. TRUCK BODY AND EQUIPMENT ASSOCIATION (TBEA) Ambulance Manufacturers Division (AMD) Standards AMD 001 - Static Load Test for Body Structure. AMD 003 - Oxygen Tank Retention Syst
24、em. AMD 004 - Litter Retentionsystem. * discontinued operations. Use alternate publications, if copies of TBEB publicationa are not on hand.) (Sources for copies of TBEA publicationa are not -known, since llI3EA (Non-Government standards and other publications are normally available from the organiz
25、ations that prepare or distribute the documenta. documents also may be available in or through libraries or other informational services.) I These 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LE407X 23 7777906 0454308 L MIL-T-l2407X( AT )
26、* 2.3 Order nf mecedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, aupersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIRRM
27、ENTG * 3.1 citemq . The electrical system shall be in accordance with Federal Motor Carrier Safety Regulations 393.27 through 393.31 and 393.33, * 3.4.2.1 Startine: system !-el en- . For diesel engine driven vehicles, a 12 or 24-volt direct current (dc) starting system, with a 12-volt dc lighting sy
28、stem, shall be furnished. Unless otherwise specified (see 6.2), a minimum 90-ampere alternator shall be furnished. Engine starting equipent shall include an ether starting system, glow plug or grid heater. If an ether system is furnished in lieu of a glow plug or grid heater, it shall be of the meas
29、ured shot type. The measured shot type ether ayatem shall be key operated or manually operated from the drivers compartment, and shall be inoperative with the engine warm. Complete psovisiona for a replaceable reservoir of not lesa than 12 fluid ounces shall be furnished. A reservoir need not be fur
30、nished. 3i4.2.2 .- evstem IpaFioliaie en- I For gaaoline engine driven vehicles, a 12-volt dc system shall be furniahed. (see 6.2), an alternator of not less than 60 amperes rated capacity shall be furnished which provides a dc ouput capacity, at normal engine idle speed, adequate to support al1 ele
31、ctrical loads operating simultaneously. Unless otherwise specified 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-/ - MI L=T- 12407X( AT ) / _Ax- - - * 3,4.2.3 m. Kach battery shall be of 12-volt potential. The total reserve capacity ratings and
32、the total cold cranking ratinga at OoF, both measured in accordance with SAE 3537, shall be not lese than specified in table I. The batteries ahall. be of the maintenance-free. type having the maintenance-free Characteristics listed in W-B-132. When specified (aee 6.2), a high cycle life (deep cell)
33、 battery shall be provided. Tabla I. 393.67(d); and 393.67(f) ia not required. The total capacity of the fuel tank(s) shall be not lesa than 20 gallons. gasoline engine driven Vehicles, a selector valve connecting either tank to the engine fuel intake shall be provided, and means shall be provided t
34、o monitor the fuel level of either tank from a single gage; or an equalizing pump shall be used ta maintain thesame fuel level in both tanks. When more than one tank is furnished an diesel engine driven vehicles, means shall be . provided to assure an equalized fuel level in both tanks or a selector
35、 valve and fuel monitor gage as described above shall be furnished. vehicle shall have the fue tank protected by a metal ahield (skidplate). “he tank shall be located in an area which will be free from hazards encountered in cross-country operations. When more than one tank is furnished on Model 4x4
36、 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-LZq07X 23 979790b 045L13Lb O 3.4.3.1 . An air cleaner shall be furnished. 3.4.4 Jhhaustn, The exhaust system shall conform to Federal Motor Carrier Safety Regulation 393.83. rear of the body o
37、r to the side behind the rear wheels, and shall be so located as to minimize the possibility of exhaust fumes entering the body. The exhaust tailpipe shall extend to the 3.4.5 Gear tr uismiaaipn 3.4.5,2), the vehicle shall be provided with an automatic tmnsmission. input torque capacity of the trans
38、mission shall be at least equal to the maximum torque delivered by the engine. than three forward gear ratios and one reverse gear ratio. shall include a hydraulic torque converter and an oil cooler. - -=- Unless otherwise specified, (see The The transmission shall have not less The transmission . W
39、hen specified (see 6.2), a manually * 3.4.5.2 Manual tr- shifted transmission shall be provided. The input torque capacity of the transmission shall be at least equal to the maximum torque delivered by the engine. The transmission shall have not less than three forward speeds and one reverse speed.
40、shifting with synchronized shift for at least the two highest forward speeds. performance specified in 3.3.1 through 3-3.1.2. .* The transmisaion shall provide for the maximum ease of Transmission and axle gear ratios shall be selected to provide the * 3.4.5.3 Clutch. The clutch shall be the largest
41、 capacity dutch offered for the type of vehicle anrd aiae of engine furnished, with the clutch torque capacity exceeding the maximum delivered engine. torque. The clutch lining shall be asbestos free, . * 3.4.6.4 Dans2w c a, $e. Mcleb 4x4 vehicles shell be provided with a two- speed tralltlser cam.
42、The tranafel case shall pinovide for drivea. selection of either two-e.?heel or four-wheel drive. The speedometer ahall Ingad accwate ap2ed (nph) c.Jith the speed selctor in high OF low Emge. 3.4.6.1 IBl t 4xu Unless otherwise specified (aee 6.2), a heavy duty skid plate shall be installed protectin
43、g the engine and transmission (from ground contact) if there is leas thm 15 inches S% clearance to the ground. The skid plate shall be demountable %or servicing the engine and the transmission. draining of the transmission and servicing the underside of the engine. Openings shall be provided to enab
44、le Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-12Y07X 23 7997906 011511337 2 M MIL-T-l2407X( AT) * 3.4.7 FrAme. The frame shall be the manufacturers atandard for the vehicle furnished. 3.4.8 Cuszwnsioxi. The vehicle shall be equipped with
45、a suspension system, with components having a rated capacity at least equal to the load hpoaed on each member, measured at the ground, with the vehicle loaded to the specified GVW. When suspeneion ia rated at the apring pads, unsprung weight shall be deducted. 3.4.8.1 Ch I Chassis equipment shall be
46、 complete with all accessories furnished as standard equipment by the manufacturer. The following minimum equipment shall be furnished: Inside rearview mirror Key-operated ignition switch Ammeter, voltmeter or charging indicator Oil prerssure gage Engine temperature gage Speedometer with recording o
47、dometer Drivers compartment ventilator other than window Dual sunviaora Front door mounted armrest on drivers side When manual tranamission is furnished, a hand throttle control mounted on the instrument panel ihmelight in drivera compartment. - - shall incorporate a body frame of welded constructio
48、n with the roof assembly, exterior sides, and rear covered with sheet metal panels symmetrically rounded; and shall embody provisions for doors and windows specified herein. The cab and body shall meet the static load test for ambulance body structure, AMD standard 001. sides and doors shall be line
49、d with washable, fire retardant and mildew resistant, high strength, formica or marlite panels or an approved equivalent. edges or shall be provided with heavy duty, bright finiah, corrosion- resistant metal trim. formica, marlite, vinyl, or fiberglass reinforced plastic. compartments apecif ied herein shall be oonstructed of marine grade plywood conforming to class I of MIL-P-18066, with pressure bonded lamin
