1、Beneficial comments (recommendations, additions, deletions) and any pertinent . data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Impro
2、vement Proposal (DD Form 1426) appearing at the end of this document or by letter. 0 - E3 -449 I INCH-POUND 1 /- MIL-T-43182D 9 January i989 SUPERSEDING MIL-T-43182C 16 August 1974 MILITARY SPECIFICATION TENTS, MISSILE SYSTEM EQUIPMENT CONSOLE (HAWK) This specification is approved for use by all Dep
3、artments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers four different frame-supported tents for sheltering console, maintenance test shop, aft radar and front radar assemblies of the Hawk Missile System. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1
4、.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specificati
5、ons and Standards (DODISS) and Bupplement thereto, cited in the solicitation (see 6.2). . SPECIFICATIONS FEDERAL V-F-106 - Fasteners, Slide, Inter locking V-T-285 - Thread, Polyester QQ-A-225/8 - Aluminum Alloy 6061, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn or Cold Finished I AMSC N/A FSC 8
6、340 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. - -, THIS DOCUMENT CONTAINS 50 PAGES. - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-B -6 1 3 QQ-S -7 6 3 TT-E-529 TT-P-595 TT -P - 1 75 7 DDD-L -20 PPP-B -
7、60 1 - MIL-T-43LZD 3 W 7773706 0372442 I W . MILITARY MIL -P -5 O 1 MIL -R - 1 670 MIL -L - 1 709 MIL-S-I 734 MIL -P -23 83 MIL-C-2399 MIL -C- 10578 MIL -F - 1 08 8 4 MIL-C- 12095 MIL-G- 16491 MIL -T -4 35 6 6 STAN DARDS FEDERAL FED-STD- 191 FED- S TD-7 5 I MILITARY MIL-STD- 105 MIL-STD- 129 MIL-STD
8、- 147 MIL-STD-731 MIL-T-43182D - Brass, Leaded and Non Leaded: Flat Products - Steel Bars, Wire Shapes and Forgings, Corrosion- (Plate, Bar, Sheet and Strip) Res is ting - Enamel, Alkyd, Semi-Gloss - Preservative Coating, Canvas - Primer Coating, Zinc Chromate, Low-Moisture - Label: For Clothing, Eq
9、uipage, and Tentage, - Boxes, Wood, Cleated-Plywood Sensitivity (General Use) - Pins, Tent, Metal - Rope, Tent-Lay - Lines, Tent - Slips, Tent Line - Pins, Tent, Wood - Cement, Liquid, Tent Patching - Corrosion Removing and Metal Conditioning Compound - Fasteners, Snap - Cloth, Wind-Resistant Sateen
10、, Cotton; - Grommet, Metallic - Tape, Textile, Cotton or Polyester, General Purpose, ( Phosphoric Acid Base) Fire and Water Resistant Natural or in Colors - Textile Test Methods - Stitches, Seams, and Sti tchings - Sampling Procedures and Tables for Inspection - Marking for Shipment and Storage - Pa
11、lletized Unit Loads - Quality of Wood Members for Containers and Pallets by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 1
12、9120-5099.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-T-LI3182D 83 7779706 0372Lt43 3 MIL-T-43182D I 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a
13、 part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the soicitation. Department of the Army Field Manual FM 10-16 General Repair of Tents, Canvas and Webbing (Copies are available from the Superintendent of Documents, U. S. Printing Office
14、, Washington, D .C. 20402) DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT CW ACQUISITION RADAR AND CW ILLUMINATOR RADAR (HAWK SYSTEM) 5 -4 -7 12 5 -4 -7 13 5-4-715 5-4-71 6 5-4-717 5-4-71 8 5-4 -790 5 -4 -7 14 - Assembly and Illustration - Details - Details and Views - Details Assembly Complete - D
15、etails - Guy Line Lug and Blackout Curtain Details 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43182 TENT, PULSE ACQUISITION RADAR, FRONT 5-4-639 5-4-641 5-4-640 5-4-642 5 -4 -643 5 -4 -659 5-4-660 5-4-792 View Assembly and Illustration D
16、etai 1 s Details and Views Details Assembly Complete Details Blackout Curt ai n Detail s (Copies of drawings are available from the U.S. Army Natick Research, Development , and Engineering Center, Natick, MA 01760-5014.) 2.2 Non-Government publications. The following document(s1 form a part of this
17、document to the extent specified herein. Unless otherwise specified , the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents
18、cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS A 108 - Steel Bars, Carbon, Cold-Finished, Standard Quality B 241 - Aluminum and Aluminum-Alloy D 3951 - Standard Practice for Commercial Packaging Seamless Pipe and Seamless Extruded Tube (Application for copies should
19、be addressed to the American Society for Testing and Materials, 191 6 Race Street, Philadelphia, PA 19103.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through lib
20、raries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. regulations unless a specific exemption has been obtained. Nothing in this document , however, s
21、upersedes applicable laws and 3. 3*1 first 3 *2 RE QU I RE ME NT S First article. When specified (see 6.21, a sample shall be subjected to article inspection (see 6.3) in accordance with 4.3. Materials and components. Materials and components shall be as specified herein. 3.2.1 Cloth, cotton, sateen
22、. The wind-resistant cloth shall conform to MIL-C-12095 and shall match shade OG 107. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-VIID 3 7977906 0372q45 7 MIL-T-43182D 3.2.2 Cloth, polyester. The natural color, water repellent treated po
23、lyester cloth used for light ports shall conform to the following requirements (see 4.4.1 .l): Physical Properties: Fiber - Polyester Weave - Plain, 1 x 1 Texture- Threads per inch minimum) : Warp 80 ends Filling 64 picks Warp 290 Filling 265 Breaking strength-lbs (grab), (minimum) : Weight, oz/sq.y
24、d - 5.5 (plus or minus 0.5). Spray rating - 90, 90, 80 (three determinations). Finishing Properties: A water repellent of the silicone type shall be used; however, other water-repellent compounds may be used -if approved by the contracting officer, (see 6.4). The fabric shall be scoured, calendered,
25、 and heat set. be natural and the fabric shall have a maximum air permeability of 1.5 CU. ft./min/sq. ft. and a minimum of 40 percent luminous transmission. The color shall 3.2.3 Tape textile, cotton. The tape shall be 3/4, 1-1/2, and 2 inch widths, shade Olive Drab No. 7, conforming to type I, clas
26、s 4 of MIL-T-43566. 3.2.4 Thread, polyester. The thread shall conform to type I, class 1, sub- class. B, shade s-1 (Cable No. 66022) of V-T-285. The dyed thread shall show fastness to weathering equal to or better than the standard shade sample (see 6.4). When no standard shade sample is available,
27、the dyed thread shall show good fastness to weathering. Thread sizes shall be as follows: For all stitching on tent, except stitching - Size F for needle and E for bobbin indicated by llZ1l on drawings and bartacking For stitching on tent indicated by llZ“ on drawings For bartacking 5 - Size F for n
28、eedle and E for looper - Size E for needle and bobbin Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43L82D 83 7777706 0372446 7 M MIL-T-43 182D 3.2.6 Fasteners, slide, interlocking. The slide fasteners shall conform to size H, wire stirrup pu
29、lls of V-F-106. shall be type V, style 1 or 3 and for the light port and personnel door shall be type III, style 1, The slide fastener chain shall be fabricated of brass or polyester coil, The slider for the brass chain shall be brass and the slider for the polyester coil shall be die cast zinc allo
30、y. The slide fastener t.ape shall be dyed to match Olive Drab shade S (CA 66519) and be water repellent and mildew-resistant. mildew-resistance .) The color of the tape after treatment will be considered acceptable. The tape shall show good fastness to weathering. Alternatively, the slide fastener c
31、hain shall be polyester continuous monofilament in a ladder or coil type configuration, finish brass and the sliders shall be brass. The fastener for the front wall section (Tapes made of 100 percent polyester need not be tested for Color of the chain shall be olive drab or natural 3.2.7 Rope, manil
32、a. The manila rope shall conform to type 1, class 2, 1/4 inch diameter of MIL-R-1670. 3.2.8 Lines, tent. The tent lines shall conform to MIL-L-1709. Types shall be as follows: Type 1 (footstop) Type XXIII, except that the end finish shall be in accordance with figure 19 of MIL-L-1709 (guy line) 3.2.
33、9 Fastener, snap. The snap fastener shall conform to style 2, finish 2, button 24 line, size 1 and eyelet, size 1 of MIL-I?-10884. 3.2.10 Eyelet and washer. The eyelet and washer (quarter-turn stud fastener) shal.1 be brass, black finish, conforming to the United Carr Company components, eyelet BS 7
34、8403 and washer BS 78505, or equal. 3.2*11 Socket and clinch plate. The long-pronged socket and clinch plate (large curtain type) shall conform to style 1, finish 2 of MIL-F-10884. 3.2.12 Grommet, oblong and washer. 3.2.12.1 Eyelet. The oblong eyelet shall be brass, black finish, conforming to No. A
35、867 of Edwin B. Stimpson, Inc., or equal. 3.2.12.2 Washer. The oblong washer shall be fabricated of 1/2 hard brass, dull black finish conforming to composition 1 or 2 of QQ-B-613 in the dimensions as shown on Drawings 5-4-642, 5-4-647, 5-4-657 and 5-4-715. 3.2.13 Pipe, aluminum alloy. The aluminum a
36、lloy pipe shall conform to 6061-T6, schedule 40, 1-1/4-inch nominal pipe size, or ASTM B 241. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LI3L2D 3 W 777770b 0372447 O - MIL-T-43182D 3.2.14 Bar, aluminum alloy. The aluminum alloy bar for the
37、 lunette support and the inner top support (see Drawing 5-4-718) shall conform to 6061-T6 of ._ QQ-A-225 /8. 3.2.15 Pins, tent. 3.2.15.1 Metal. The metal tent pin shall be type II, 12-inches long conforming to MIL-P-501. 3.2.15.2 Wood. The wooden tent pin shall be size 1 conforming to MIL-P-2383. 3.
38、2.16 Slips, tent line. The nylon tent line slip shall conform to type II Of MILS-1734 3.2.17 Steel, carbon bar. The steel used to fabricate the diagonal side support spindle (see Drawing 5-4-659) shall conform to identification number 1211, 1212, 1213, or 1215, round form, cold finished, as specifie
39、d in ASTM A 108. 3.2.18 Steel., corrosion-resisting bar. The corrosion-resisting steel bar for the lunette support rod (see Drawing 50-4-659) shall conform to the 300 series as specified in QQ-S-763. 3.2.19 Pretreating coating. The pretreating coating shall conform to MIL-C-10578. 3.2.20 Primer. The
40、 primer shall conform to composition G or L, as applicable, color Y or T, of TT-P-1757. 3.2.21 Enamel. The enamel shall.conform to TT-E-529. The color shall correspond to Olive Drab color No. 24087. 3.3. Construction. The construction shall conform to the drawings listed in section 2 and to the repi
41、rements specified herein. 3.3.1 Stitching, machine. 3.3.1.1 Types of stitching. All stitch types, except bartacking shall conform to FED-STD-751 as follows: For all stitching, except stitching indicated by iiZ“ on the drawings. - Type 301, 5 to 7 stitches per inch. 7 Provided by IHSNot for ResaleNo
42、reproduction or networking permitted without license from IHS-,-,-MIL-T-43182D For stitching indicated by OZ“ on drawings. For bar t ac ki ng - Type 401, 5 to 7 stitches per inch. Chain portion of stitching shall not appear on outside of tent. - Bartack, 7/8 plus or minus 1 /16 inch long, 1/8 f 1/32
43、 inch wide (bight) shall contain 42 stitches. 3.3.1.2 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched 1/2 inch minimum except when caught in other stitching or turned under in a hem. Thread tension shall be maintained so that there will be no loose stitching resulting
44、 in puckering of material sewn. The lock shall be embedded in the material sewn. 3-3.1.2.1 be as follows: Repairs of type 301 stitching. RepairSW type ,301 stitching shall a, When thread breaks or bobbin run-outs occur during sewing, the stitching shall be repaired by restarting the stitching a mini
45、mum of 1 inch behind the end of the stitching. - 1/ b. Thread breaks or two or more consecutive skipped stitches or run-off stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of 1 inch before the defective are
46、a (1 /2 inch on box, box and cross, and W-W stitching) and continue a minimum of 1 inch beyond the defective area onto the existing stitching, the defective stitching, without damaging the materials, and restitching in the required manner. - I/ required to be backstitched. Loose or excessively tight
47、 stitching shall be repaired by removing 1/ When making the above repairs, the ends of the stitching are not 3.3.1.3 Type 401 stitching. Thread tension shall be maintained so that there will be no loose stitching. Both ends of all seams or stitching produced with a 401 stitch type, when not turned u
48、nder in a hem or held down by other stitching, shall have a 1 /2 to 3/4 inch chain extending beyond each end. The looper (under thread) shall always be on the inside of the tent or cover. be made in accordance with 3.3.1.2.1a or 3.3.1.2.1b. Repairs may be made using 301 stitch type. All repairs shal
49、l Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43182D 83 7977706 0372i47 4 W - 9 MIL-T-4 3 1 8211 ,=- 3.3.1.4 Automatic stitching. Automatic stitching machines may be used to perform any of the required stitch patterns provided the requirements for stitch pattern, stitches per inch, and size and type of thread are met, and at least three ty
