1、AMENDMENT 2 MIL-T-50595C (2) 13 9999906 1210600 568 W r 1 FNCH-POUND I MIL-T-50595C(AR) AMENDMENT 1 O9 October 1987 MILITARY SPEC1 FICATI ON TRIPOD ASSEMBLY, DEMOLITION KIT, M180, METAL PARTS FOR AND ASSEMBLY This amendment forms a part of MIL-T-50595C (AR), dated O1 March 1979, and is approved for
2、use by the US Army Armament, Munitions, and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense PAGE 5 Table I: Change “M57 Firing Device, Modified (DWg. 9244458) to “Firing Device, Antipersonnel Mine, Electrical M57 (Dwg. 8800924 I“. Add the follo
3、wing to Table I: “Cover, Protective (DWg. 12598668) 4.4.2 .13A“ Examination for Defect i0 100% 3.1 * Delete references to “Firing Device, Antipersonnel Mine, Electrical M57“ and “Cover, Protective“ in their entirety. PAGE 6 * TABLE I: Change “Strap Assembly“ to “Strap Assembly, Tripod“, * Add the fo
4、llowing to TableI: “Strap Assembly, Tripod (Alternate) (DWg. 9270969) 3.1 4.4.2.20A Examination for defects 10 100% Salt spray Test (a) 100% 3.1 4.5.3“ Yield Strength (a) 100% 3.1 4.5.2 O AMSC NfA 1 of 5 FSC 1375 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unl,.nited. Prov
5、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-50595C (2) 13 999990b 1210601 4T4 MIL-T-50595C (AR) AMENDMENT 2 PAGE 20 4.4.2.13: Change TITLE to Firing Device, Antipersonnel Mine, Electrical M57“ Change DRAWING NUMBER to “8800924 under “Critical“
6、Change “1 Safety pin missing or loose 100% 3.1 Visual“ to “None defined“. * Delete in its entirety. PAGE SOA 4.4.2.13: Add new 4.4.2.13A included. * Delete in its entirety PAGE 27 * 4.4.2.20: Change TITLE to “Strap Assembly, Tripod“ PAGE 27A * 4.4.20A: Add new 4.4.2.20A inclded. PAGE 29 4.4.2.22: Ad
7、d the following under “Critical“: “1 M57 Protective Cover missing 100% 3.1 Visual“ Add the following under “Major“ “109 Bail visible (1) 100% 3.1 Visual“ Add the following under NOTES: “(1) If bail is visible, the protective cover should be removed, the bail placed in the safe/vertical position and
8、the cover reinstalled.“ * Delete “Critical Defect i“, “Major Defect log“, and “NOTE 1“ in their entirety. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-T-50595C (2) 13 999990b 1210602 330 I 4 Y V m c i 1% 3 (ZOA) Provided by IHSNot for Resal
9、eNo reproduction or networking permitted without license from IHS-,-,-MIL-T-50595C (2) 13 W 9997906 3230603 277 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-50595C (AR) AMENDMENT 2 PAGE 30 - * 4.5.2: Delete the following: “Yield strength of
10、strap assembly (Dwg. 9329696) major defect. Ten(l0) assemblies shall be selected from each lot for thisest, And replace with: “Yield strength. Ten(l0) strap assemblies (DWg. 9329696) or twenty (20) alternate strap assemblies (Dwg. 9270969) shall be selected from each lot for this test.“ 4.5.4: Chang
11、e “(DWg. 9244458)“ to “(Dwg. 8800924)“ * Delete in its entirety. The margins of this amendment are marked with an ansterisk or vertical lines to indicate where changes (additions, modification, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the
12、 Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Cu s t o d i an : Ar my- AR Preparing activity: Army-AR (Project 1375-A489) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
