1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 3155-078 Edition P 2 November 2017 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Supersede
2、s edition P 1 of September 2013 and will supersede EN 3155-078:2014 Descriptors: ENGLISH VERSION Aerospace series Electrical contacts used in elements of connection Part 078: Contacts size 22 for EN 2997, electrical, male, type A, crimp, class S Product standard Luft- und Raumfahrt Elektrische Konta
3、kte zur Verwendung in Verbindungselementen Teil 078: Elektrische Stiftkontakte Gre 22, fr EN 2997, Typ A, crimpbar, Klasse S Produktnorm Srie arospatiale Contacts lectriques utiliss dans les organes de connexion Partie 078 : Contacts lectriques taille 22 pour EN 2997, mles, type A, sertir, classe S
4、Norme de produit This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the expert
5、s of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by
6、users and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level
7、by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entirely voluntary,
8、and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirmed, stabilized or cancell
9、ed. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, with
10、out prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st November 2017 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2017 ASD-STAN prE
11、N 3155-078:2017 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics 4 5 Designation . 9 6 Marking . 10 7 Technical specification . 10 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical D
12、omain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3155-078:2017 (E) 3 1 Scope This standard specifies the required characteristics and tests applicable to male e
13、lectrical contacts 078, type A, crimp, class S, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated female contacts are defined in EN 3155-079. 2 Normative references The following documents, in whole or in part, are normatively referen
14、ced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2083, Aerospace series Copper or copper alloy conductors for electrical c
15、ables Product standard EN 2591 (all parts), Aerospace series Elements of electrical and optical connection Test methods EN 2997 (all parts), Aerospace series Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 65 C to 175 C continu
16、ous, 200 C continuous, 260 C peak EN 3155-001, Aerospace series Electrical contacts used in elements of connection Part 001: Technical specification EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts EN 3155-079, Aerospace seri
17、es Electrical contacts used in elements of connection Part 079: Contacts size 22 for EN 2997, electrical, female, type A, crimp, class S Product standard EN 4434, Aerospace series Copper or copper alloy lightweight conductors for electrical cables Product standard (Normal and tight tolerances) ISO 8
18、843, Aircraft Crimp-removable contacts for electrical connectors Identification system 1) SAE-AS22520, Crimping tools, wire termination, general specification for 2) SAE-AS81969, Installing and removal tools, connector electrical contact, general specification for 2) 3 Terms and definitions For the
19、purposes of this document, the terms and definitions given in EN 3155-001 apply. 1) Published by: International Organization for Standardization (ISO), http:/www.iso.ch/ 2) Published by: National (US) Society of Automotive Engineers (SAE ),http:/www.sae.org/ prEN 3155-078:2017 (E) 4 4 Required chara
20、cteristics 4.1 Specific characteristics Type A contacts are for general application and class S corresponds to an operating temperature range from 65 C to 200 C. 4.2 Dimensions and mass See Figure 1. Dimensions and tolerances are given in millimetres and apply after surface treatment. Mass: 0,16 g m
21、ax. Key 1 One side only 2 Electrical engagement point 3 See EN 3155-001 for length of selective protection “LSP” definition 4 Colour bands, see Table 1. Figure 1 Connector contact 4.3 Marking by colour code See Table 1. prEN 3155-078:2017 (E) 5 Table 1 Marking by colour code Colour identification ba
22、nds according to ISO 8843 Size Contact Barrel Band 1 Band 2 a 22 22 Green Green As an alternative, when the two band colours are the same, only one band of 2 mm width nominal can be applied. a The width of the band 2 shall be twice the width of the band 1. 4.4 Material, surface treatment Body materi
23、al: copper alloy. Surface treatment: gold on an appropriate undercoat, thickness of protection see EN 3155-001, selective protection permitted. 4.5 Permissible cables See Table 2. Table 2 Permissible cables Size Size of conductors Rated test current A Contact Barrel ASD code Section mm2 AWG a 22 22
24、004 0,40 22 5 002 0,25 24 3 001 0,15 26 2 a AWG Closest American Wire Gauge. 4.6 Tooling 4.6.1 Crimping tools Conform to SAE-AS22520, see Table 3. The qualification selector numbers used for crimping copper or copper alloy conductors in cables EN 2083 or EN 4434 are indicated in Table 3. It is the r
25、esponsibility of the user if the parameters in Table 3 are changed for service use. prEN 3155-078:2017 (E) 6 Table 3 Crimping tools Contact Cable size Tool M22520/2-01 Contact size Barrel size ASD code AWG a Positioner Selector number 22 22 001 26 M22520/2-23 3 002 24 3 004 22 5 a AWG = Closest Amer
26、ican Wire Gauge. 4.6.2 Insertion/Extraction tools Conform to SAE-AS81969. See Table 4. Table 4 Insertion/Extraction tools Size Insertion tools Extraction tools Contact Barrel 22 22 M81969/1-01 or M81969/14-01 M81969/1-01 or M81969/14-01 4.7 Cable stripping See Table 5. Table 5 Cable stripping Size S
27、tripped length of cable mm 0,5 Contact Barrel 22 22 4,5 4.8 Tests Contacts shall be fitted in connector EN2997SC1221AX and EN2997SA1221BX with heat shrinkable boot (or equivalent) and lacing tapes (see Figure 2) for tests in accordance EN 3155-001. prEN 3155-078:2017 (E) 7 Key 1 Connector with integ
28、rated accessory 2 Heat shrinkable boot (without glue) or equivalent; Lacing tape to be placed at 40 mm from the rear of connector grommet (no mechanical stress shall be introduced) 3 Harness 4 Lacing tape pitch shall be every 50 mm max. starting from the first lacing tape, see key 2 5 First clamping
29、 point Figure 2 Test sample configuration Suitable contact arrangements: 12-21 (for contacts size 22) to be filled as follows, see Figure 3: 12-21 Figure 3 Suitable contact arrangements Above non blank cavities shall be wired. Additional samples shall be prepared and be carried out for high temperat
30、ure 200 C/vibration with same sample configuration as Group 2 from EN 3155-001. Contact to be crimped on conductor as per EN 2083 or EN 4434 code D. Tests according to EN 2591-100, see Table 6. prEN 3155-078:2017 (E) 8 Table 6 Tests EN 2591- Designation of the test Not applicable Applicable Accordin
31、g to EN 3155-001 Remarks 101 Visual examination X 102 Examination of dimensions and mass X See 4.2. 201 Contact resistance - low level X 202 Contact resistance at rated current X 203 Electrical continuity at microvolt level X 204 Discontinuity of contacts in the microsecond range X 206 Measurement o
32、f insulation resistance X 207 Voltage proof test X 210 Electrical overload X 211 Capacitance X 212 Surface transfer impedance X 213 Shielding effectiveness from 100 MHz to 1 GHz X 220 Contact/conductor joint ageing by current and temperature cycling X 221 Voltage Standing Wave Ratio (VSWR) X 222 Ins
33、ertion Loss (I.L) X 223 Measurement of characteristic impedance of a coaxial connector or contact X 301 Endurance at temperature X T (200 2) C Duration: 1 000 h 305 Rapid change of temperature X TA (200 +5/0) C TB ( 65 0/5) C 306 Mould growth X 307 Salt mist X 315 Fluid resistance X 316 Ozone resist
34、ance X 319 Gastightness of solderless wrapped connections X 402 Shock X As per EN 2997-001; Following group 2: EN 2591-402 403 Sinusoidal and random vibration X As per EN 2997-001; Following group 2: EN 2591-403 and group 9: EN 2591-403 406 Mechanical endurance X prEN 3155-078:2017 (E) 9 EN 2591- De
35、signation of the test Not applicable Applicable According to EN 3155-001 Remarks 415 Test probe damage (female contacts) X 416 Contact bending strength X 417 Tensile strength (crimped connection) X 418 Gauge insertion/extraction forces (female contacts) X 424 Stripping force, solderless wrapped conn
36、ections X 425 Unwrapping capability, solderless wrapped connections X 501 Soft solderability X 502 Restricted entry X 503 Contact deformation after crimping X 507 Plating porosity X 508 Measurement of thickness of coating on contacts X The measured thickness shall be recorded. 509 Adhesion of coatin
37、g on contacts X 513 Magnetic permeability X 514 Solderability of contacts with self-contained solder and flux X 4.9 Gauges See EN 3155-001. 5 Designation EXAMPLE Description block CONTACT, ELECTRICAL Identity block EN3155-078M2222 Number of this standard Type of contact: M: male Contact size (see Table 1) Barrel size (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. prEN 3155-078:2017 (E) 10 6 Marking See EN 3155-001. 7 Technical specification See EN 3155-001.
