1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3545-006 Edition P 2 December 2013 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: 49.060 Supersedes edition P
2、 1 of April 1995 and will supersede EN 3545-006:2006Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 006: Male coding and attachment system for mounting on fi
3、xed housing (receptacle) Product standard Srie arospatiale Connecteurs lectriques, rectangulaires, tanches et non tanches larrire, botier en plastique, verrouillage, tempratures dutilisation 55 C 175 C Partie 006 : Systme de fixation et de codage mle pour montage sur botier fixe (embase) Norme de pr
4、oduit Luft- und Raumfahrt Elektrische Rechtecksteckverbinder mit und ohne hintere Abdichtung, Plastikgehuse, Verriegelungssystem, Betriebstemperaturen von 55 C bis 175 C Teil 006: Stiftkodierung und Befestigungszubehr fr feste Steckverbinder Produktnorm This “Aerospace Series“ Prestandard has been d
5、rawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent
6、 to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as
7、 a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any nati
8、onal standards conflicting with the EN. Edition approved for publication 1st December 2013 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2013 by ASD-STAN prEN 3545-006:2013 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative referenc
9、es 3 3 Terms and definitions . 3 4 Required characteristics . 3 4.1 Dimensions, mass . 3 4.2 Material, surface treatment . 6 4.3 Main general characteristics 6 5 Designation 6 6 Technical specification . 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrica
10、l Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3545-006:2013 (E) 3 1 Scope This standard specifies the male coding and attachment system for mounting on fi
11、xed housing in the family of rectangular electrical connectors with sealed and non-sealed rear, plastic housing, locking device, for operating temperatures from 55 C to 175 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are ind
12、ispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3545-001, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic
13、housing, locking device, operating temperatures 55 C to 175 C Part 1: Technical specification EN 3545-002, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 2: Specification of performance
14、 and contact arrangements FED-STD-H28/2A:1978, Screw thread standards for federal services 1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3545-001 apply. 4 Required characteristics 4.1 Dimensions, mass The dimensions of attachment system are given
15、in Figures 1, 2 and 3. Dimensions and tolerances are in millimetres. Mass: 6 g max. 1) Published by: DoD National (US) Mil. Department of Defense http:/www.defenselink.mil/ prEN 3545-006:2013 (E) 4 Key 1 Position indicator (recessed circle) 2 6 flats 8,00,100,053 0.1120 inch - 40 UNC-3B according to
16、 FED-STD-H28 4 Relieved 5 Male body 6 Retaining ring 7 X (see Figure 3) 8 Chamfer 3,500,29 0.2500 inch - 28 UNF-3A according to FED-STD-H28 10 0,3 to 0,4 at 30 Figure 1 Male coding and attachment system prEN 3545-006:2013 (E) 5 Key 1 Washer with two corrugations in dichromate-sealed cadmium plated s
17、teel 2 0.2500 inch - 28 UNF-3B according to FED-STD-H28 3 0,3 at 45 4 0,5 at 45 5 Nut Washer and nut are fitted on the male body Figure 2 Washer and nut 0,025 General concentricity View on F Retaining ring Detail X Figure 3 Retaining ring prEN 3545-006:2013 (E) 6 4.2 Material, surface treatment Body
18、: steel, cadmium-plated, dichromate sealed Retaining ring: beryllium copper, cadmium-plated, dichromate sealed 4.3 Main general characteristics See EN 3545-002. Tightening torque of the panel mounting nut: 0,125 daNm to 0,150 daNm 5 Designation EXAMPLE Description block CONNECTOR, CODING SYSTEM Identity block EN3545-006B Number of this standard B: male attachment system for mounting an fixed housing (receptacle) NOTE lf necessary, the code I9005 shall be placed between the description block and the identity block. 6 Technical specification See EN 3545-001.
