1、ASD STANDARD NORME ASD ASD NORM prEN 3645-009 Edition P1 November 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Ae
2、rospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 C or 200 C continuous Part 009: Receptacle, round flange, jam nut mounting Product standard Srie arospatiale Connecteurs lectriques circulaires contacts protgs, accouplement par fil
3、etage pas rapide trois filets, tempratures dutilisation 175 C ou 200 C continu Partie 009 : Embase collerette ronde fixation par crou Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung Dauerbetriebstemperaturen 175 C oder 200 C
4、Teil 009: Fester Steckverbinder mit rundem Schwei und Mutternbefestigung Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The Aerospace and Defense Industries Association of Europe - Standardization). It is published for the needs of the Europea
5、n Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, withou
6、t re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national me
7、mbers have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 November 2005 Comments should be sent within six months after the date of publication to ASD
8、-STAN Electrical Domain Copyright 2005 by ASD-STAN Page 2 prEN 3645-009:2005Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manu
9、al, this standard has received approval for Publication. Contents Page 1 Scope3 2 Normative references.3 3 Terminology4 4 Required characteristics 4 4.1 Dimensions, weights.4 4.2 Materials and surface treatment7 4.3 Recommended panel cut-out7 4.4 Electrical, mechanical and climatic characteristics8
10、5 Designation8 6 Marking10 7 Technical specification .10 Page 3 prEN 3645-009:20051 Scope This standard specifies the characteristics of jam nut mounting receptacles in the family of circular, electrical connectors, with triple start threaded coupling. It applies to models in table 3. For plugs and
11、protective covers, see EN 3645-006, EN 3645-008, EN 3645-011 and EN 3645-012 respectively. For filler plugs and rear accessories associated with this receptacle, see EN 3645-002. These connectors are derived from and interchangeable with models W, F, J, M and K in specification MIL-DTL-38999/24. 2 N
12、ormative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated and undated references, subsequent amendments to o
13、r revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3645-001, Aerospace series Connectors electrical, circular, scoop-proof, triple start t
14、hreaded coupling, operating temperature 175 C or 200 C continuous Part 001: Technical specification 1) EN 3645-002, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 002: Specification of performance an
15、d contact arrangements 1)EN 3645-006, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 006: Protective cover for receptacle Product standard 1)EN 3645-008, Aerospace series Connectors electrical, circu
16、lar, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 008: Non release plug with grounding ring Product standard 1)EN 3645-011, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C
17、or 200 C continuous Part 011: Lanyard release plug with grounding fingers Type 1 Product standard 1)EN 3645-012, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 012: Lanyard release plug with groundin
18、g fingers Type 2 Product standard 1)MIL-DTL -38999/33, Connectors, electrical, circular, receptacle, jam-nut mounting, hermetic, triple start threaded coupling, removable crimp contacts, series III, metric 2) 1)Published as AECMA Prestandard at the date of publication of this standard 2)Published by
19、: Department of Defence (DOD), The Pentagon, Washington D.C. 20301 USA Page 4 prEN 3645-009:20053 Terminology See EN 3645-001. 4 Required characteristics 4.1 Dimensions, weights Dimensions and tolerances are in millimetres. Page 5 prEN 3645-009:2005(without seal) Seal (Seal Slot with close edges) Ke
20、y 1 Red strip 2 3 holes 1,5 min. for brake wire (see option according to Detail D) 3 Models J and M 4,54 , other models: 3,17 029,0+045,0+4 Blue strip 5 H on flats 6 B on flat 7 Seal Figure 1 Jam nut receptacle Note: One disengagement is permissible to accept the accessory mounting. Page 6 prEN 3645
21、-009:2005Table 1 Jam-nut receptacle Dimensions A B C 1) D E F 2) G Shell size 0,3 15,010,0+20,010,0+03,013,0+ 0,13 max. Thread 09 30,2 16,53 17,40 15,9 M17x1 6g 0,1 R 11 34,9 19,07 20,60 18,8 M20x1 6g 0,1 R 13 38,1 23,82 25,40 2,39 1,14 23,8 M25x1 6g 0,1 R 15 41,3 26,97 28,50 26,8 M28x1 6g 0,1 R 17
22、44,5 30,15 31,85 30,8 M32x1 6g 0,1 R 3) 19 49,2 33,32 34,90 33,8 M35x1 6g 0,1 R 21 52,4 36,50 37,903,58 1,91 36,8 M38x1 6g 0,1 R 23 55,6 39,67 41,20 39,8, M41x1 6g 0,1 R 25 58,7 42,85 44,40 42,8 M44x1 6g 0,1 R H P S W Y Z Mass (g) max. 1,04,0+ 0,4 1,07,0+Aluminium Stainless steel Composite 24,00 21,
23、82 27,0 20,50 20,19 15 35 12 27,00 24,99 31,8 25,27 24,97 21 45 16 32,00 29,77 34,9 2,2 28,45 28,14 1,85 1,70 27 60 21 36,00 32,91 38,1 31,62 31,32 32 70 27 37,00 36,12 14,3 41,3 34,80 34,49 40 90 31 41,00 39,25 46,0 37,92 37,62 49 104 43 46,00 42,47 49,2 41,20 40,69 2,69 2,54 54 117 50 50,00 45,61
24、52,4 3,0 44,37 43,86 65 132 55 55,00 53,54 55,6 47,55 47,04 73 158 65 1) Dimensions C and 1,5 mm shall be compatible with the panel hole 2) Diameter F corresponds to the start of the thread 3) Upper diameter modified as follow: 31,95 max. 31,80 min; Page 7 prEN 3645-009:2005 4.2 Materials and surfac
25、e treatment See Table 3. 4.3 Recommended panel cut-out Dimensions and tolerances are in millimetres. Figure 2 Panel cut-out Panel thickness : 3,20 max. 1,60 min. Table 2 Panel cut-out Dimensions Shell size A 025,0+B 25,00C min 09 17,70 16,99 31,80 11 20,88 19,53 35,00 13 25,58 24,26 39,40 15 28,80 2
26、7,53 42,50 17 31,98 30,68 45,70 19 35,15 33,86 48,50 21 38,28 37,06 51,70 23 41,50 40,24 54,90 25 44,68 43,41 58,00 Page 8 prEN 3645-009:20054.4 Electrical, mechanical and climatic characteristics See EN 3645-002. 5 Designation EXAMPLE: Description block JAM-NUT ELECTRICAL CONNECTOR Identity block E
27、N3645-F6GN35MA Number of the basic standard Model according to Table 3 Shell code for nut fitting receptacle Shell size code according to Table 4 Letter indicating if the contact arrangement have grounded cavities or not N: no grounded cavity G: grounded cavities Contact arrangement according to EN
28、3645-002 Contact code according to Table 4 Polarisation: N, A, B, C, D, E NOTE: If necessary, the code I9005 shall be placed between the classification block and the identity block. Page 9 prEN 3645-009:2005 Table 3 Model coding Model Description W Sealed receptacles, with shell in cadmium-plated al
29、uminium alloy, olive green Salt spray resistance 500 h Plug with shielding ring with elastic earthing system Crimped contacts Maximum operating temperature 175 C continuous J Sealed receptacles, with shell in cadmium-plated composite polymer, olive green Salt spray resistance 2 000 h Plug with shiel
30、ding ring with elastic earthing system Crimped contact 1 500 operations Maximum operating temperature 175 C continuous F Sealed receptacles, with shell in nickel-plated aluminium alloy Crimped contacts Plug with shielding ring with elastic earthing system Maximum operating temperature 200 C continuo
31、us M Sealed receptacles, with shell in nickel-plated plastic composite Salt spray resistance 2 000 h Plug with shielding ring with elastic earthing system Crimped contacts 1 500 operations Maximum operating temperature 200 C continuous K Sealed receptacles, with shell in passivated stainless steel S
32、alt spray resistance 500 h Plug with shielding ring with elastic earthing system Fire resistant Crimped contacts Maximum operating temperature 200 C continuous Table 4 Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21 G 23 H 25 J Page 10 prEN 3645-009:2005 Table 5 Contact code Contacts Product marking Order coding Supplied without contacts Supplied with contacts EN 3155-xxxx22-22 EN 3155-xxxx20-20 EN 3155-xxxx16-16 EN 3155-xxxx12-12 EN 3155-xxxx10-10 Male M A M Female F B F 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001.
