1、ASD STANDARD NORME ASD ASD NORM prEN 3645-013 Edition P1 November 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Ae
2、rospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 C or 200 C continuous Part 013: Dummy receptacle Product standard Srie arospatiale Connecteurs lectriques circulaires contacts protgs, accouplement par filetage pas rapide trois fil
3、ets, tempratures dutilisation 175 C ou 200 C continu Partie 013 : Embase de repos Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung Dauerbetriebstemperaturen 175 C oder 200 C Teil 013: Blinddose Produktnorm This “Aerospace Seri
4、es“ Prestandard has been drawn up under the responsibility of ASD-STAN (The Aerospace and Defense Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following m
5、ember comments. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-ST
6、AN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard
7、and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 November 2005 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN Page 2 prEN 3645-013:2005Foreword This standard was re
8、viewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope3 2 Normative references.3
9、3 Definitions.3 4 Required characteristics 4 4.1 Dimensions, weights.4 4.2 Materials and surface treatment5 4.3 Recommended panel cut-out5 4.4 Electrical, mechanical and climatic characteristics6 5 Designation6 6 Marking.7 7 Technical specification 7 Page 3 prEN 3645-013:20051 Scope This standard sp
10、ecifies the characteristics of dummy receptacles in the family of circular, electrical connectors, with triple start threaded coupling. It applies to models in table 3. For plugs and protective covers, see EN 3645-006, EN 3645-008, EN 3645-011 or EN 3645-012 respectively. These receptacles are deriv
11、ed from and interchangeable with those in specification MIL-DTL-38999/22. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are l
12、isted hereafter. For dated and undated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3645-001,
13、Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 001: Technical specification 1) EN 3645-002, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling, operat
14、ing temperature 175 C or 200 C continuous - Part 002: Specification of performance and contact arrangements 1)EN 3645-006, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 006: Protective cover for
15、 receptacle - Product standard 1)EN 3645-008, Aerospace series - Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 008: Non release plug with grounding ring - Product standard 1)EN 3645-011, Aerospace series - Connect
16、ors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 011: Lanyard release plug with grounding fingers - Type 1 - Product standard 1)EN 3645-012, Aerospace series - Connectors electrical, circular, scoop-proof, triple start thre
17、aded coupling, operating temperature 175 C or 200 C continuous - Part 012: Lanyard release plug with grounding fingers - Type 2 - Product standard 1)MIL-DTL-38999/22, Connectors, electrical, circular, receptacle, dummy stowage, series III, metric 2)3 Definitions See EN 3645-001. 1)Published as AECMA
18、 Prestandard at the date of publication of this standard 2)Published by: Department of Defence (DOD), The Pentagon, Washington D.C. 20301 USA Page 4 prEN 3645-013:20054 Required characteristics 4.1 Dimensions, weights See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. Key 1 Red
19、strip 2 Seal NOTES: a Detail size 9 only b optional detail for Models J and M Figure 1 Page 5 prEN 3645-013:2005Table 1 Shell K P PP R1 R2 S V W U Mass g max. size max. 02,0+02,0+ 0,3004,1+012,0+Models F and W Model K 09 11,84 5,49 18,26 15,09 23,80 1) 7 20 11 15,01 20,62 18,26 26,20 7,24 11 32 13 1
20、9,08 23,01 20,62 28,60 19,502,80 8,66 15 44 15 22,25 3,25 4,9324,61 23,01 31,00 2,20 10,24 18 52 17 25,43 26,97 24,61 33,30 11,84 22 64 19 28,60 29,35 26,97 36,50 13,16 26 75 21 31,78 31,75 29,36 39,70 3,5014,76 30 87 23 34,95 3,91 6,15 34,93 31,75 42,90 18,70 2,9016,33 33 96 25 38,13 38,10 34,93 46
21、,00 17,93 36 104 1) U size 9 = 5,61 06,004.2 Materials and surface treatment See Table 3. 4.3 Recommended panel cut-out See Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Rear panel mounting Front panel mounting Page 6 prEN 3645-013:2005Figure 2 Table 2 Shell size A min. C 0,13
22、D min. R1 R2 09 16,66 31,80 18,26 15,09 11 20,22 35,00 20,62 18,26 13 23,42 39,40 23,01 20,62 15 26,59 3,25 42,50 24,61 23,01 17 30,96 45,70 26,97 24,61 19 32,94 48,50 29,36 26,97 21 36,12 51,70 31,75 29,36 23 39,29 3,8154,90 34,93 31,75 25 42,47 58,00 38,10 34,93 4.4 Electrical, mechanical and clim
23、atic characteristics See EN 3645-002. 5 Designation EXAMPLE: Description block DUMMY RECEPTACLE Identity block EN3645-F 5 G Number of the basic standard Model according to Table 3 Shell code for dummy receptacle (see EN 3645-002, Table 9) Shell size code according to Table 4 Note: If necessary, the
24、code I9005 shall be placed between the classification block and the identity block. Table 3 Model coding Models Description W Dummy receptacles, with shell in cadmium-plated aluminium alloy, olive green Salt spray resistance 500 h Maximum operating temperature 175 C continuous F Dummy receptacles, w
25、ith shell in nickel-plated aluminium alloy Maximum operating temperature 200 C continuous K Dummy receptacle, with shell in stainless steel Maximum operating temperature 200 C continuous Page 7 prEN 3645-013:2005Table 4 Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21 G 23 H 25 J 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001.
