1、ASD STANDARD NORME ASD ASD NORM prEN 3660-014 Edition P 1 May 2007 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Avenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERS
2、ION Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 014: Cable outlet, style A, 90, unsealed, with cable tie strain relief Product standard Srie arospatiale Accessoires arrires pour connecteurs circulaires et rectangulaires lectriques et
3、optiques Partie 014 : Raccord, type A, coud 90, non tanche, avec tenue du cble par frettage Norme de produit Luft- und Raumfahrt Endgehuse fr elektrische und optische Rund- und Rechtecksteckverbinder Teil 014: Endgehuse, Bauform A, 90, nicht abgedichtet, mit Arm fr Kabelbinder Produktnorm This “Aero
4、space Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain f
5、ollowing member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement
6、of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national
7、standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 May 2007 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2007 by ASD-STAN prEN 3660-014:20072 Contents Page Foreword2 1 Scop
8、e 3 2 Normative references 3 3 Terms and definitions .3 4 Characteristics.3 5 Designation 8 6 Marking .9 7 Technical specification .9 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the r
9、ules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3660-014:20073 1 Scope This product standard defines a range of cable outlets, 90, style A, for use under the following conditions: Associated electrical connector(s) : EN 3660-002
10、 Temperature range, Class N : 65 C to 200 C Class W : 65 C to 175 C 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced doc
11、ument (including any amendments) applies. EN 2591-*, Aerospace series Elements of electrical and optical connection Test methods. EN 3660-001, Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 001: Technical specification. 1)EN 3660-002, Ae
12、rospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 002: Index of product standards. 1)AS85049, Connector Accessories, Electrical General Specification for- 2)3 Terms and definitions For the purposes of this document, the terms and definitions
13、given in EN 3660-001 apply. 4 Characteristics 4.1 Dimensions and mass For dimensions and mass, see Figure 1 to Figure 3 and Table 1. For spacer pad, see Figure 4. For interface dimensions, see 4.2. All its parts quoted. 1) Published as ASD Prestandard at the date of publication of this standard. 2)
14、Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001. prEN 3660-014:20074 All dimensions in millimetres Key Key 1 Thread A 2 Teeth N (see Table 2) 3 Area for cable tie or lacing cord 4 Knurled, manufacturers option 1 Three off wire lock holes e
15、qui-spaced for 0,8 mm max. diameter wire Figure 1 Figure 2 Key 1 Marking (see Clause 6) Figure 3 Figure 4 Spacer pad Table 1 B Ca D E F E Radius H Shell size A Thread Class 2B max. 0,38 max. + 0,2 0 max. Mass max. Classes N & W Mass max. Spacerpad inches mm mm mm mm mm mm mm g g 08 0.4375-28UNEF 16
16、6,70 22,6 2,1 19,1 5 10 0.5625-24UNEF 19 16,90 9,95 24,1 2,9 19,9 6 12 0.6875-24UNEF 22 12,85 37,3 3,8 20,9 8 14 0.8125-20UNEF 25 17,06 16,02 33,8 4,8 22,0 9 16 0.9375-20UNEF 29 17,46 19,20 35,3 5,7 22,6 11 18 1.0625-18UNEF 31 21,46 37,6 7,1 24,9 15 20 1.1875-18UNEF 35 24,63 42,3 7,1 24,9 16 22 1.31
17、25-18UNEF 38 27,80 47,0 7,8 25,4 18 24 1.4375-18UNEF 41 6,29 17,60 30,90 48,5 8,8 26,7 21 0,65 a“C” dimension is taken when the coupling nut is pulled in forward position. prEN 3660-014:20075 4.2 Interface dimensions 4.2.1 Associated connector See EN 3660-002. 4.2.2 Standard AS85049 interface See Fi
18、gure 5, Figure 6 and Table 2. All dimensions in millimetres aAfter max. 5,4 mm from the root of the teeth, the cable outlets coupling nut must conform to the G diameter. Figure 5 Figure 6 Table 2 G H I J max. max. min. max. min. max. Shell size mm mm mm mm N Number of teeth 08 15,20 10,26 9,7 10,01
19、7,59 8,80 12 10 18,40 13,36 12,9 13,16 10,85 12,00 16 12 21,60 16,54 15,8 16,33 13,79 14,94 20 14 24,80 19,51 19,0 19,30 16,92 18,06 24 16 28,00 22,68 22,1 22,48 20,09 21,23 28 18 31,00 25,58 24,9 25,30 22,78 23,93 32 20 34,20 28,88 28,0 28,68 25,96 27,10 36 22 37,40 31,93 31,2 31,65 29,13 30,26 40
20、24 40,60 35,10 34,4 34,82 32,21 33,34 44 prEN 3660-014:20076 4.3 Material and finish Cable outlet: Material/Finish Class N : Aluminium/Electroless nickel Material/Finish Class W : Aluminium/Olive drab cadmium plate Spacer: Fluorosilicone, colour green 4.4 Assembly torque These torque values are inte
21、nded for installation use only, see Table 3. Table 3 Shell size Torque Nm 0,5 08 10 12 14 16 18 4,5 20 22 24 9,0 4.5 Coupling thread strength torque These torque values are for test purposes, see EN 2591-420 and Table 4. Table 4 Shell size Torque Nm 0,5 08 10 12 14 16 18 5,5 20 22 24 11,0 prEN 3660-
22、014:20077 4.6 Tests Test details to be in accordance with Table 5 and EN 3660-001. Qualification to be in accordance with EN 3660-001. Table 5 EN 2591 Test No. Title Not applicable Applicable see EN 3660-001 Particulars 101 Visual examination X 102 Examination of dimensions and mass X See 4.1. 205 H
23、ousing (shell) electrical continuity X 212 Surface transfer impedance (from 100 MHz to 1 GHz) aX 301 Endurance at temperature X 305 Rapid change of temperature X 306 Mould growth X For variant A only 307 Salt mist X Cable outlet not fitted to a connector and suspended with non-metallic cord. Duratio
24、n: Class N 48 h Class W 500 h 308 Sand and dust X 314 Immersion at low air pressure X 315 Fluid resistance X For variant A only 316 Ozone resistance X 317 Flammability X For variant A only 318 Fire-resistance X 402 Shock X Method A. Severity 100 g Number of shocks: 6 One in each direction in 3 perpe
25、ndicular axes 403 Sinusoidal and random vibration X Method B. Figure 3 and Table 2. Level J Duration: 8 h at ambient temperature 406 Mechanical endurance X 408 Mating and unmating forces X continued prEN 3660-014:20078 Table 5 (concluded) EN 2591 Test No. Title Not applicable Applicable see EN 3660-
26、001 Particulars Phase A Shell size Load N max. 08 10 12 44,5 14 16 18 89,0 20 22 133,5 24 156 420 Mechanical strength of rear accessories X Phase D and Table 4 422 Locking wire hole strength X 513 Magnetic permeability X Not fitted to a connector. Max. value Classes N & W 2,0 a1 GHz to 10 GHz under
27、consideration. 5 Designation EXAMPLE EN3660-014N08A Cable outlet, style A, aluminium, electroless nickel, shell size 08, with spacer pad. Description block CABLE OUTLET Identity block EN3660-014N08A Number of this standard Material/Finish class, see 4.3 Shell size Variant A with spacer pad NOTE 1 No gaps are required between sections in the part number when printed. NOTE 2 If necessary, the code I9005 shall be placed between the description block and the identity block. prEN 3660-014:20079 6 Marking Refer to EN 3660-001 and Figure 1. 7 Technical specification Refer to EN 3660-001.
