1、AECMA STANDARD NORME AECMA AECMA NORM prEN 3733-007 Edition P 1 May 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Aerospac
2、e series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 007: Ferrule (optical contact) for EN 4532 (200 m/280 m fibre) Product standard Srie arospatiale Connecteur optique circulaire monovoie, accouplement par bague filet
3、e, temprature dutilisation 150 C continu Partie 007 : Ferrule (contact optique) pour cble EN 4532 (fibre 200 m/280 m) Norme de produit Luft- und Raumfahrt Optischer Rundsteckverbinder einpolig Schraubkupplung, Betriebstemperatur 150 C konstant Teil 007: Druckhlse (optischer Kontakt) fr Kabel nach EN
4、 4532 (200 m/280 m fiber) Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved
5、by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination a
6、nd review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level
7、by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 May 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Electrical Domain Copyright 2005 by AECMA-STAN prEN
8、 3733-007:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA-STANs General Process Manual, this standard has received approval for Publicatio
9、n. Contents Page 1 Scope . 3 2 Normative references 3 3 Terms and definitions . 4 4 Required characteristics 4 5 Designation. 5 6 Marking 5 7 Technical specification 5 prEN 3733-007:20053 1 Scope This standard specifies the characteristics of ferrules (optical contacts) for aerospace series single c
10、ore optical fibre as incorporated in EN 4532, operating temperature up to 150 C. Connector interface dimensions, table of tests and qualification approval requirements, are contained in the Technical Specification EN 3733-001. EN 3733-002, List of product standards, includes the listings of product
11、types, codification and applicable combinations of product types. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docum
12、ent (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General.1)EN 3733-001, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous
13、Part 001: Technical specification. 1)EN 3733-002, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 002: List of products standards.1)EN 3733-003, Aerospace series Connector, optical, circular, single channe
14、l, coupled by self-locking ring, operating temperature up to 150 C continuous Part 003: Plug connector for cable to EN 4532 Product standard.1)EN 3733-004, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 0
15、04: Receptacle, connector, four hole fixing for cable to EN 4532 Product standard.1)EN 3733-005, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 005: Receptable, connnector, two hole fixing for cable to EN
16、 4532 Product standard.1)EN 3733-006, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 006: Receptable, connector, jam unt fixing for cable to EN 4532 Product standard.1)EN 3733-008, Aerospace series Connec
17、tor, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 008: Plug sub-assembly for cable to EN 4532 (200 m/280 m fibre) Product standard.1)EN 3733-009, Aerospace series Connector, optical, circular, single channel, coupled by self-locki
18、ng ring, operating temperature up to 150 C continuous Part 009: Receptacle sub-assembly for cable to EN 4532 (200 m/280 m fibre) Product standard.1)EN 4532, Aerospace series Cables, optical, single core 200 m/280 m fibre, 2,5 mm outer jacket Technical specification. 1)1) Published as AECMA Prestanda
19、rd at the date of publication of this standard. prEN 3733-007:20054 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 and the following apply. 3.1 ferrule (optical contact) optical contact assembly comprising an alignment component (terminating
20、 the fibre) together with a component for providing fibre buffer support and location within the connector 4 Required characteristics 4.1 Dimensions and mass Dimensions (in millimetres) shall be as shown in Figure 1. Key 1 4 keyways permissible Figure 1 Mass: 0,7 g max. 4.2 Materials Zirconia cerami
21、c, nickel-copper alloy body. 4.3 Application combinations This component is supplied as an integral part of products conforming to Product Standards EN 3733-003 to EN 3733-006, EN 3733-008 and EN 3733-009. 1 prEN 3733-007:20055 5 Designation EXAMPLE Description block FERRULE, FIBRE OPTIC Identity bl
22、ock EN3733-007 Number of the basic standard Product standard (see EN 3733-002) NOTE If necessary, the code I9005 may be placed between the description block and the identity block. 6 Marking Not applicable. 7 Technical specification This component is qualified as part of a complete connector assembly when tested to the qualification requirements of EN 3733-001 and the applicable Product Standards.
