1、ASD STANDARD NORME ASD ASD NORM prEN 3733-104 Edition P 1 October 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8111 - www.asd-stan.orgICS: 49.060 Descriptors: Aerospace industry
2、, aircraft, aircraft equipment, optical connector, elements of opticalconnection, optical contact, characteristics, test, quality assurance ENGLISH VERSION Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 1
3、04: Receptacle connector dummy four holes fixing Product standard Srie arospatiale Connecteur optique circulaire monovoie, accouplement par bague filete, temprature dutilisation 150 C continu Partie 104 : Embase de repos, quatre trous de fixation Norme de produit Luft- und Raumfahrt Optischer Rundst
4、eckverbinder einpolig Schraubkupplung, Betriebstemperatur 150 C konstant Teil 104: Blindsteckdose mit vierlochflansch Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The European Association of Aerospace Industries - Standardization). It is pub
5、lished for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected,
6、 physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European
7、 Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 October 2005 Comments should be sent within six months af
8、ter the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN prEN 3733-104:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in A
9、SD-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope . 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics 3 4.1 Dimensions and mass 3 4.2 Panel cut-out and mounting of connectors . 4 4.3 Materials . 5 4.4 Applicati
10、on combinations 5 5 Designation. 5 6 Marking 6 7 Technical specification 6 prEN 3733-104:20053 1 Scope This standard specifies the characteristics of receptacle connector dummy four holes fixing for single channel fibre optic plug connectors, operating temperature up to 150 C. Connector interface di
11、mensions, table of tests and qualification approval requirements, are contained in the Technical Specification EN 3733-001. EN 3733-002, List of product standards, includes the listings of product types, codification and applicable combinations of product types. 2 Normative references The following
12、referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optica
13、l connection Test methods Part 100: General. EN 3733-001, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 001: Technical specification. 1)EN 3733-002, Aerospace series Connector, optical, circular, single
14、channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 002: List of product standards.1)EN 3733-003, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 003: Plug connector fo
15、r cable to EN 4532 Product standard.1)EN 3733-004, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 004: Receptacle, connector, four hole fixing for cable to EN 4532 Product standard.1)3 Terms and definitio
16、ns For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Dimensions and mass Dimensions (in millimetres) shall be as shown in Figure 1. 1) Published as AECMA Prestandard at the date of publication of this standard. prEN 3733-104:20054
17、 Key 1 Maximum panel thickness rear mounted 3,0 2 Seal 3 Thread 4 Four holes 3,10 0,05 typical Figure 1 Mass: 13,1 g max. 4.2 Panel cut-out and mounting of connectors Panel cut-out and connector mounting details shall be as shown in Figures 2 and 3 respectively. Dimensions are in millimetres. Key 1
18、Rear panel mount only 2 Four holes 3,50 0,10 typical 3 Recommended Figure 2 21 3 43 1 2 18,30 min.prEN 3733-104:20055 Key 1 Panel 2 Screw head Figure 3 4.3 Materials Nickel-copper shell, fluorosilicone seal. 4.4 Application combinations This dummy receptacle is for use with Product Standards conform
19、ing to EN 3733-003 and incorporates universal keying to enable any plug connector keyway orientation to be accommodated. See EN 3733-002 for applicable combinations of accessories and connectors. 5 Designation EXAMPLE Description block DUMMY RECEPTACLE, FOUR HOLES Identity block EN3733-104B Number o
20、f the basic standard Product standard (see EN 3733-002) Class (see EN 3733-001, test fluids class B) NOTE 1 Part number spacing as shown is for clarity only. NOTE 2 If necessary, the code I9005 may be placed between the description block and the identity block. Front mounting Rear mounting 1 12 2 prEN 3733-104:20056 6 Marking See EN 3733-001. 7 Technical specification Dummy receptacle connectors are qualified by read-across to the applicable qualification requirements of Product Standard EN 3733-004, receptacle connector four holes fixing.
