ASD-STAN PREN 3859-1993 Aerospace Series Titanium Alloy TI-P19001 Annealed Sheet and Strip Hot Rolled a Less Than or Equal to 6 mm (Edition P 1)《航空航天系列 钛合金TI-P19001制a≤6mm的热轧经退火处理的薄.pdf
《ASD-STAN PREN 3859-1993 Aerospace Series Titanium Alloy TI-P19001 Annealed Sheet and Strip Hot Rolled a Less Than or Equal to 6 mm (Edition P 1)《航空航天系列 钛合金TI-P19001制a≤6mm的热轧经退火处理的薄.pdf》由会员分享,可在线阅读,更多相关《ASD-STAN PREN 3859-1993 Aerospace Series Titanium Alloy TI-P19001 Annealed Sheet and Strip Hot Rolled a Less Than or Equal to 6 mm (Edition P 1)《航空航天系列 钛合金TI-P19001制a≤6mm的热轧经退火处理的薄.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、CEN PRENJ3859 93 m 3404589 004470b 125 m Edition approved for publication 1993-04-26 AECMA STANDARD NORME AECMA AECMA NORM C5 Chairman M. ODORICO Comments should be sent within six months after the date of publication to AECMA Technopolis - 1 75, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux
2、Cedex - FRANCE prEN 3859 Edition P 1 April 1993 EDITE PAR LASSOCIATION EUROPEENNE DES CONSTRUCTEURS DE MATERIEL AEROSPATIAL Technopolis - 175, rue Jean-Jacques Rousseau - F-92138 Issy-les-Moulineaux Cedex - Tl. (1 1 47.36.98.76 UDC : Descriptors : ENGLISH VERSION Aerospace series Titanium alloy TI-P
3、I 9001 Annealed Sheet and strip, hot rolled aI6mm Srie arospatiale Alliage de titane TI-Pl 9001 Recuit Tles et bandes, lamines chaud al6mm Luft- und Raumfahrt Titanlegierung TI-Pl9001 Geglht Bleche und Bnder, warmgewalzt alemm This “Aerospace Series“ Prestandard has been drawn up under the responsib
4、ility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee follo wing comment by the Member countries. Subsequent to the publicatio
5、n of this prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official
6、Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. COPYRIGHT Association Europeene Des Constructeurs de Materiel AerospaceLicensed by Information Handling ServicesCEN PRENr3859 93 3404589 0044707 Ob1 W p
7、rEN 3859 Page 3 O Introduction For the use of this standard, see EN 2500-4. 1 Scope and field of application This standard specifies the requirements relating to sheet and strip, hot rolled, a I6 mm, annealed, in titanium alloy TI-Pl9001 for aerospace applications. 2 References EN 2338 EN 2500-4 EN
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASDSTANPREN38591993AEROSPACESERIESTITANIUMALLOYTIP19001ANNEALEDSHEETANDSTRIPHOTROLLEDALESSTHANOREQUALTO6MMEDITIONP1
![提示](http://www.mydoc123.com/images/bang_tan.gif)
链接地址:http://www.mydoc123.com/p-452598.html