1、ASD STANDARD NORME ASD ASD NORM prEN 4008-015 Edition P1 November 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION Aerospace
2、 series Elements of electrical and optical connection Crimping tool and associated accessories Part 015: Positioner for crimping tool M22520/2-01 Product standard Srie arospatiale Organes de connexion lectrique et optique Outils de sertissage et accessoires associs Partie 015 : Positionneur pour pin
3、ce sertir M22520/2-01 Norme de produit Luft- und Raumfahrt Elektrische und optische Verbindungselemente Crimpwerkzeug und zugehriges Zubehr Teil 015: Positionierer fr Crimpzange M22520/2-01 Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The Ae
4、rospace and Defense Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technic
5、al content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European C
6、ommittee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition appr
7、oved for publication 30 November 2005 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN prEN 4008-015:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inq
8、uiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope .3 2 Normative references .3 3 Terminology 3 4 Required characteristics3 4.1 Description 3 4.2 Dimensions and
9、mass4 4.3 Material, surface treatment4 5 Designation .5 6 Marking 5 7 Technical specification 5 prEN 4008-015:20053 1 Scope This standard specifies the characteristics for the positioner used with M22520/2-01 crimping tool to crimp electrical contact according to EN 4008-002. 2 Normative references
10、This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publ
11、ications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 001 : General 1)EN 4008-001,
12、 Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 001 : Technical specification 1)EN 4008-002, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 002 : List of product standards 1)
13、MIL-C-22520/2-01, Crimping tools, contact, electric, hand for shielded outer contacts 2)3 Terminology See EN 2591-100. 4 Required characteristics 4.1 Description Securing the positioner on the crimping tool is provided by the combined action of the two bayonets and the pressure from the internal spr
14、ing on the central moving part (locator). The appropriate longitudinal positioning of the contact with respect to the crimping tool indenters is performed by the contact butting against a shoulder on the central part bore. Locator shall be spring loaded so as to depress 0,79 mm with a force of (9 4,
15、5) N. 1)Published as AECMA Prestandard at the date of publication of this standard. 2)Published by : Department of Defence (DOD), the Pentagon, Washington D.C.20301 USA. prEN 4008-015:20054 4.2 Dimensions and mass. Dimensions of positioner are given in figure 1. Mass : 11 g max. Dimensions and toler
16、ances are given in millimetres. General tolerances : 0,25 mm Key 1 Bayonet lock pin 1,09 0,025 2 Locator in extended position 3 Stamp on this surface EN 400-005 use with M22520/2-01 a Use with contact WIRE WK WL WS XY WG EN 3155-028 EN 3155-029 SEL 2 2 2 1 1 Figure 1 Positioner 4.3 Material, surface
17、 treatment Positioner body : aluminium alloy, color blue Positioner locator : stainless steel Not applicable prEN 4008-015:2005 5 5 Designation EXAMPLE: Description block Identity block POSITIONER EN 4008-015 Number of this standard NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See figure 1. 7 Technical specification See EN 4008-001.
