1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 4165-022 Edition P 2 November 2016 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Supersede
2、s edition P 2 of February2003 and will supersede EN 4165-022:2006 Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 022: Insertion/extraction tool for removal of modules Product standard Luft- und Raumfahrt Elektris
3、cher Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 C konstant Teil 022: Ein- und Ausbauwerkzeug fr Module Produktnorm Srie arospatiale Connecteurs lectriques rectangulaires modulaires Temprature dutilisation 175 C continu Partie 022 : Outils dinsertion/extraction pour modules N
4、orme de produit This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts
5、 of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by u
6、sers and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level b
7、y giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entirely voluntary, a
8、nd its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirmed, stabilized or cancelle
9、d. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, witho
10、ut prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st November 2016 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2016 ASD-STAN prEN
11、 4165-022:2016 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics 3 5 Insertion/extraction tool . 4 6 Designation 6 7 Identification and marking 6 8 Technical specification 6 Foreword This standard was reviewed by the Domain Techn
12、ical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4165-022:2016 (E) 3 1 Scope This standard defines the insertion/extra
13、ction tool for removal of modules used in the family of rectangular electrical connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies.
14、 For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4165-001, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification 3 Terms and definitions For the purposes of t
15、his standard, the terms and definitions given in EN 4165-001 apply. 4 Required characteristics See Figure 1 and Figure 2. prEN 4165-022:2016 (E) 4 5 Insertion/extraction tool 5.1 For extraction of sealed and standard modules See Figure 1. Dimensions in millimetres. Figure 1 prEN 4165-022:2016 (E) 5
16、5.2 For insertion of sealed modules See Figure 2. Dimensions in millimetres. Figure 2 prEN 4165-022:2016 (E) 6 6 Designation EXAMPLE Description block INSERTION EXTRACTION TOOL FOR REMOVAL MODULES Identity block EN4165TN Number of the basic standard T: tool N: extraction S: insertion 7 Identification and marking Marking shall be applied to the tool. This marking shall include: The identity block as defined in Clause 6; The date of manufacture (year-week); The manufacturers name or trade mark. 8 Technical specification See EN 4165-001.
