1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 4839-003 Edition P 1 December 2016 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Descriptors: ENG
2、LISH VERSION Aerospace series Arc Fault Circuit breakers, three-pole, temperature compensated, rated current 3 A to 25 A, 115/200 V a.c. 400 Hz constant frequency Part 003: Without auxiliary contacts Product standard Luft- und Raumfahrt Schutzschalter, lichtbogen (berschlags) sensitiv, dreipolig, Te
3、mperaturkompensiert, Nennstrme von 3 A bis 25 A, 115/200 V a.c. 400 Hz Konstantfrequenz Teil 003: Ohne Signalkontakt Produktnorm Srie arospatiale Disjoncteurs tripolaires dtection darc compenss en temprature, intensits nominales 3 A 25 A, 115/200 V a.c. 400 Hz frquence fixe Partie 003 : Sans contact
4、s auxiliaires Norme de produit This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved
5、 by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination
6、and review by users and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at n
7、ational level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entire
8、ly voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirmed, stabili
9、zed or cancelled. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or o
10、therwise, without prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st December 2016 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 201
11、6 ASD-STAN prEN 4839-003:2016 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Dimension and mass 4 5 Characteristics . 5 6 Designation. 10 7 Rated current code 10 8 Delivery codes . 10 9 Marking 11 10 Technical specification . 11 Foreword This standard
12、 was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4839-003:2016 (E) 3 1 Scope This sta
13、ndard specifies the required characteristics for three-pole, arc fault circuit breakers, rated currents from 3 A to 25 A, switching capacity 65 In, for use in aircraft electrical systems. Their operating temperatures are between 40 C to 85 C at a maximum altitude of Z = 15 000 m. The thermal protect
14、ion is temperature compensated and operates between 55 C and 125 C. These arc fault circuit breakers are operated by a push-pull type single pushbutton (actuator), with delayed action “trip-free“ tripping. They will continue to function up to the short-circuit current. 2 Normative references The fol
15、lowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3841-100, A
16、erospace series Circuit breakers Test Methods Part 100: General EN 3841-305, Aerospace series Circuit breakers Test Methods Part 305: Short-circuit performance EN 4839-001, Aerospace series Arc fault circuit breakers, three-pole, temperature compensated, rated current from 3 A to 25 A, 115 V a.c. 40
17、0 Hz constant frequency Part 001: Technical specification EN 6113, Aerospace series Circuit breaker, connecting and attachment hardware TR 6083, Aerospace series Cut-outs for installation of electrical components 1) FED-STD-595B, Colours used in Government Procurement 3 Terms and definitions For the
18、 purposes of this document, the terms and definitions given in EN 3841-100 apply. 1) Published as ASD-STAN Technical Report at the date of publication of this standard by Aerospace and Defense industries Association of European-Standardization (ASD-STAN) (www.asd-stan.org) prEN 4839-003:2016 (E) 4 4
19、 Dimension and mass 4.1 Dimensional characteristics The circuit breakers do not have to correspond to the pictorial illustration, only the dimensions given shall be adhered to. Dimensions are in millimetres. See Figure 1. Key 1 Push button released 7 Lockwasher 2 Black colour according to FED-STD-59
20、5B 8 1,0 to 3,0 max. 3 White 9 Positioning lug in accordance with the panel cut-out, as per TR 6083C202. 4 Marking area, see Clause 9. 10 LED indicator AlInGap 592 nm Amber colour 0,65 mm diameter 5 Push button pressed 11 Rated current marking (white on black) 6 Attachment nut 12 Neutral via panel F
21、1 and F2: see EN 4839-001, Table 3. Figure 1 Configuration Dimensions Tolerances prEN 4839-003:2016 (E) 5 4.2 Electrical diagram See Figure2. Push button released: CB is open. Push button pressed: CB is closed. Key 1 Supply 2 Load 3 Neutral via metallic front plate (see Figure 1) Figure 2 Electrical
22、 diagram 4.3 Mass 170 g max. (including mounting hardware). 4.4 Panel mounting Panel cut-out : The panel cut-out is in accordance with the designation TR 6083C202 Spacing : 60 mm horizontal and 45 mm vertical from the centre of the mounting holes Panel thickness : 1 mm to 3 mm The metallic front pla
23、te of the breaker (mark J on Figure 1) is an electrical connection to neutral. For this purpose the panel mounting means must ensure a good electrical continuity to neutral. 5 Characteristics 5.1 Material, surface treatment See EN 4839-001. prEN 4839-003:2016 (E) 6 5.2 Mechanical characteristics 5.2
24、.1 Fasteners See EN 6113. 5.2.2 Recommended tightening torque of attaching nut for installation (4,0 0,25) N.m. 5.2.3 Recommended tightening torque of connection hardware for installation (1,6 0,1) N.m. 5.2.4 Resistance to vibrations 5.2.4.1 Combined test: ambient temperature at 70 and vibrations Si
25、nusoidal: 10 g-PK, see EN 4839-001. Random: 5,8 Grms, see EN 4839-001. Low frequencies: 10 g-PK, see EN 4839-001. 5.2.4.2 Combined test: ambient temperature at 85 C, altitude and vibrations Sinusoidal: 3 g-PK, see EN 4839-001. 5.2.5 Resistance to shocks 50 g-PK, see EN 4839-001. 5.2.6 Mechanical end
26、urance See Table 6. 5.3 Environment characteristics 5.3.1 Humidity See EN 4839-001. 5.3.2 Corrosion See EN 4839-001. 5.3.3 Contaminating liquids See EN 4839-001. 5.3.4 Susceptibility towards electrical perturbations See EN 4839-001. prEN 4839-003:2016 (E) 7 5.4 Electrical characteristics 5.4.1 Nomin
27、al voltage of operational circuits See Table 1. Table 1 Nominal voltage 115/200 V a.c., 400 Hz three phase 5.4.2 Voltage drop at In and low current See Table 2. Table 2 Ratings A 3 5 7,5 10 15 20 25 U max. at In V 0,55 0,35 0,30 0,30 0,25 0,25 0,20 U max. at I= 100 mA (mV) 18 8 4 2,5 2,5 2,5 2,5 NOT
28、E The test shall be performed when the contact is established (no switching). 5.4.3 Minimum and maximum tripping thresholds See Table 3. Table 3 Overload (in % of In) Ambient temperatures C Ratings Minimum thresholds value 1 h Maximum thresholds value 1 h On ground At 15 000 m On ground 23 5 All 110
29、 105 140 55 5 115 105 160 70 5 105 100 140 90 5 20 and 25 90 80 140 125 5 1 to 15 100 80 140 NOTE 1 For detection of minimum threshold, all the poles are connected in series. NOTE 2 For detection of maximum threshold, load value is: - increased by about 20 % when one pole is submitted to the load an
30、d other poles are not loaded; - increased by about 10 % when two poles are submitted to the load and the other one is not loaded; - not increased when the two other poles are loaded at 0,9 n. prEN 4839-003:2016 (E) 8 5.4.4 Overload trip See Table 4. Table 4 Overload (in % of In) 200 500 1 000 3 pole
31、s 1 pole 3 poles 1 pole 3 poles 1 pole Ambient Temperatures C Ratings A Trip time S 23 5 All 2 to 20 0,15 to 2,30 0,15 to 2,80 0,035 to 0,500 0,035 to 0,600 55 5 40 48 90 5 20 and 25 1,5 1,5 125 5 1 to 15 1,5 1,5 NOTE 1 When 3 poles are loaded, they will be connected in series. NOTE 2 When 1 pole is
32、 loaded, the two other poles are not loaded. 5.4.5 Short-circuit values See Table 5. Table 5 Nominal voltage 115 V a.c., 400 Hz Prospective currents 0,8 cos 1 65 In r.m.s. Test altitudes On the ground and at maximum altitude 15 000 m (14 000 Pa) Number of operations 1 CO a 2 OCO b 1 CO 2 OCO a Break
33、 operation (for definition refer to EN 3841-305). b Make operation (for definition refer to EN 3841-305). prEN 4839-003:2016 (E) 9 5.4.6 No-load and load endurance See Table 6. Table 6 Number or operations to be provided No-load Load 5 000 2 500 All ratings Main contacts Applicable Inductive 0,6 cos
34、 0,7 In, at 115 V a.c. - 400 Hz NOTE 1 One operation consists of one closing and one opening of the contacts. NOTE 2 Tolerances 5 % on current, voltage and frequency values. 5.4.7 Dielectric rigidity See Table 7. Table 7 Open position Z = 0 m Z = 15 000 m 1 with 2 (i.e. between A1and A2, between B1
35、and B2, between C1 and C2) 500 V a.c. 50 Hz 400 V a.c. 50 Hz NOTE Pass criteria is leakage current 100 M. 5.5 Arc fault performance Test according to EN 4839-001. prEN 4839-003:2016 (E) 10 6 Designation EXAMPLE Description block CIRCUIT BREAKER Identity block EN4839-003-20A-B Number of this standard
36、 Rated current code, see Table 9 Delivery hardware code B, see Table 10 NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 7 Rated current code See Table 9. Table 9 Ratings In 3 5 7,5 10 15 20 25 Marking on actuator 3 5 7 10 15 20 25 Rated current
37、 code 03A 05A 7A5 10A 15A 20A 25A 8 Delivery codes See Table 10. Table 10 Delivery hardware code Connection and attachment hardware kits EN 6113 Delivery conditions Kit part-No. a Included parts Pieces per part Fitted Supplied separately A EN 6113C1 Connecting screw 6 X Connecting lock washer 6 Atta
38、chment nut 1 Attachment lock washer 1 B EN 6113B1 Attachment nut 1 X Attachment lock washer 1 a Spare parts could be ordered separately, informations see EN 6113. prEN 4839-003:2016 (E) 11 9 Marking As defined on the drawing and unless otherwise specified by contract, marking shall include: the desi
39、gnation defined in Clause 6 (without delivery hardware code), on the packaging; the manufacturing date (year, week); the manufacturers name or trademark; the electrical diagram and the terminal identification; the manufacturers part number; the software and hardware version code. NOTE The marking could be combined on the both opposite faces. For electrical diagram and/or terminal identification refer to the Figure 2. 10 Technical specification See EN 4839-001.
