1、Code on Nuclear Air and Gas TreatmentAN AMERICAN NATIONAL STANDARDASME AG-12012(Revision of ASME AG-12009)Date of Issuance: May 30, 2013The next edition of this Code is scheduled for publication in 2014.ASME issues written replies to inquiries concerning interpretation of technical aspects of thisCo
2、de. Periodically certain actions of the ASME Committee on Nuclear Air and Gas Treatmentmay be published as Cases. Cases and interpretations are published on the ASME Web siteunder the Committee Pages at http:/cstools.asme.org/ as they are issued.Errata to codes and standards may be posted on the ASM
3、E Web site under the CommitteePages to provide corrections to incorrectly published items, or to correct typographical orgrammatical errors in codes and standards. Such errata shall be used on the date posted.The Committee Pages can be found at http:/cstools.asme.org/. There is an option available t
4、oautomatically receive an e-mail notification when errata are posted to a particular code orstandard. This option can be found on the appropriate Committee Page after selecting “Errata”in the “Publication Information” section.ASME is the registered trademark of The American Society of Mechanical Eng
5、ineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards. The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participa
6、te. The proposed code or standard was madeavailable for public review and comment that provides an opportunity for additional public input from industry,academia, regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or
7、 activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent, nor assumes an
8、y such liability. Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirelytheir own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is
9、 not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies, which precludes the issuance of interpretations by individuals.No pa
10、rt of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue, New York, NY 10016-5990Copyright 2013 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll
11、rights reservedPrinted in U.S.A.CONTENTSForeword xiiCommittee Roster xiiiOrganization ofASME AG-1 xvSummary of Changes xviiDivision I General Requirements . 1Section AA Common Articles 2AA-1000 Introduction 2AA-2000 Referenced Documents 7AA-3000 Materials 9AA-4000 Structural Design. 15AA-5000 Inspec
12、tion and Testing 29AA-6000 Fabrication, Joining, Welding, Brazing, Protective Coating, andInstallation 31AA-7000 Packaging, Shipping, Receiving, Storage, and Handling 43AA-8000 Quality Assurance 45AA-9000 Nameplates and Stamping. 47AA-10000 Repair and Replacement of Components 48FiguresAA-4355.3 Sin
13、e Beat Frequency and Amplitude . 23AA-4355.4 Sine Amplitude Decay Rate. 24AA-4356.4-1 Response Spectrum of Composite Excitation 25AA-4356.4-2 Oscillations Per Beat . 26AA-6324.2 Acceptable and Unacceptable Weld Profiles. 35AA-8130 Hierarchy of Responsibility 46TablesAA-3100 Allowable Materials 10AA-
14、4212 Load Conditions . 16AA-4231 Deflection Limits. 17AA-4321 Plate- and Shell-Type Components: Primary Stress Allowables 19AA-4323 Linear-Type Systems: Primary Stress Allowables 20AA-10530 Lifetime Repair and Replacement Records 50AA-10540 Nonpermanent Repair and Replacement Records. 50Nonmandatory
15、 AppendicesAA-A Design and Qualification by Analysis 51AA-B Qualification by Testing 68AA-C Qualification by a Combination of Analysis and Testing . 73Division II Ventilation Air Cleaning and Ventilation Air Conditioning 77Section BA Fans and Blowers. 78BA-1000 Introduction 78BA-2000 Referenced Docu
16、ments 80BA-3000 Materials 81iiiBA-4000 Design 82BA-5000 Inspection and Testing 88BA-6000 Fabrication and Installation of Centrifugal and Axial Fans 90BA-7000 Packaging, Shipping, Receiving, Storage, and Handling 91BA-8000 Quality Assurance 92BA-9000 Nameplates and Operating and Maintenance Manuals 9
17、3TableBA-4162 Maximum Allowable Displacement. 84Nonmandatory AppendicesBA-A Fan System Considerations 94BA-B Division of Responsibility. 96Section DA Dampers and Louvers. 98DA-1000 Introduction 98DA-2000 Referenced Documents 101DA-3000 Materials 102DA-4000 Design 104DA-5000 Inspection and Testing 11
18、1DA-6000 Fabrication, Finishing, and Installation 113DA-7000 Packaging, Shipping, and Storage 114DA-8000 Quality Assurance 115DA-9000 Nameplates, Stampings, and Manuals. 116Mandatory AppendicesDA-I Frame Leakage 117DA-II Damper and Louver Configurations 118Nonmandatory AppendixDA-A Division of Respo
19、nsibility. 124Section SA Ductwork. 126SA-1000 Introduction 126SA-2000 Referenced Documents 129SA-3000 Materials 130SA-4000 Design 131SA-5000 Inspection and Testing 137SA-6000 Fabrication and Installation 140SA-7000 Packaging, Shipping, Receiving, Storage, and Handling 145SA-8000 Quality Assurance 14
20、7SA-9000 Nameplates and Stamping. 148FigureSA-1120 Ductwork and Ductwork Support Interface Boundary . 128TablesSA-6410-1 Rectangular Ducts: Maximum Allowable Tolerances . 142SA-6410-2 Circular Ducts: Maximum Allowable Tolerances. 143SA-6410-3 Flatness of Surface: Maximum Allowable Waviness Tolerance
21、 144Nonmandatory AppendicesSA-A Division of Responsibility. 149SA-B Procedures to Determine Allowable Leakage for Ductwork . 151SA-C Additional Guidelines for Duct Design and Construction . 167Section HA Housings 169HA-1000 Introduction 169HA-2000 Referenced Documents 172HA-3000 Materials 173HA-4000
22、 Design 175HA-5000 Inspection and Testing 182HA-6000 Fabrication 185ivHA-7000 Packaging, Shipping, Receiving, Storage, and Handling 187HA-8000 Quality Assurance 188HA-9000 Nameplates and Stamping. 189FiguresHA-1120-1 Housing, Air Cleaning Unit: Walk-In Type . 170HA-1120-2 Housing, Air Cleaning Unit:
23、 Side-Access Type 170HA-1120-3 Housing, Air Conditioning Unit: Walk-In Type 171TableHA-4212 Load Combinations. 176Nonmandatory AppendicesHA-A Division of Responsibility. 190HA-B Additional Guidelines for Housing Design and Construction 191HA-C Manifold Design Guidelines . 193HA-D Performance Test fo
24、r Qualification of Sampling Manifolds . 202Section RA Refrigeration Equipment. 205RA-1000 Introduction 205RA-2000 Referenced Documents 206RA-3000 Materials 207RA-4000 Design Requirements . 209RA-5000 Inspection, Rating, and Testing 213RA-6000 Fabrication and Installation 216RA-7000 Packaging, Shippi
25、ng, Storage, and Handling. 218RA-8000 Quality Assurance 220RA-9000 Nameplates, Stamping, and Records 221FormsRA-1 Manufacturers Data Report for Section RA Non-ASME Nuclear Vessels(Customary) . 222RA-M1 Manufacturers Data Report for Section RA Non-ASME Nuclear Vessels (SI). . 224RA-2 Centrifugal Comp
26、ressor Test Record . 226RA-2a Centrifugal Compressor Oil Pump Pressure Test. 227RA-2b Centrifugal Compressor Pressure Test Record . 228RA-3 Reciprocating Scroll/Screw Compressor Test Record . 229RA-3a Reciprocating Scroll/Screw Compressor Pressure Test Record . 230RA-4 Electrical Test Record Control
27、s and Control Panels. 231RA-5 Performance Test Record (Customary) 232RA-M5 Performance Test Record (SI) . 234Mandatory AppendicesRA-I Performance Testing of Chilled Water Refrigeration Unit (Customary) . 236RA-MI Performance Testing of Chilled Water Refrigeration Unit (SI) 240RA-II Mandatory List of
28、 Instrumentation Functions and Control Functions . 244Nonmandatory AppendicesRA-A Division of Responsibility. 245RA-B Typical External Interface Diagrams 248Section CA Conditioning Equipment . 249CA-1000 Introduction 249CA-2000 Referenced Documents 251CA-3000 Materials 252CA-4000 Design 254CA-5000 I
29、nspection and Testing 264CA-6000 Fabrication and Installation 267CA-7000 Packaging, Shipping, Storage, and Handling. 269CA-8000 Quality Assurance 270CA-9000 Nameplates and Records 272vTablesCA-4122 Maximum Water Velocities in Water Coils . 255CA-8120-1 Lifetime Quality Assurance Records 271CA-8120-2
30、 Nonpermanent Quality Assurance Records 271Mandatory AppendicesCA-I Manufacturers Data Reports 274CA-II Factory Testing of Evaporative Coolers and Air Washers 278Nonmandatory AppendicesCA-A Division of Responsibility. 284CA-B Design Recommendations . 286Section FA Moisture Separators. 289FA-1000 Int
31、roduction 289FA-2000 Referenced Documents 290FA-3000 Materials 291FA-4000 Design 292FA-5000 Inspection and Testing 295FA-6000 Fabrication 297FA-7000 Packaging, Shipping, and Storage 298FA-8000 Quality Assurance 299FA-9000 Nameplates 300FigureFA-4100-1 Typical Moisture Separation Configuration 293Tab
32、leFA-4200-1 Moisture Separator Performance Specifications. 294Nonmandatory AppendixFA-A Division of Responsibility. 301Section FB Medium Efficiency Filters . 302FB-1000 Introduction 302FB-2000 Referenced Documents 303FB-3000 Materials 304FB-4000 Design 305FB-5000 Inspection and Testing 306FB-6000 Fa
33、brication 307FB-7000 Packaging, Shipping, Receiving, Storage, and Handling 308FB-8000 Quality Assurance 309FB-9000 Labels and Marking 310Nonmandatory AppendixFB-A Division of Responsibility. 311Section FC HEPA Filters . 312FC-1000 Introduction 312FC-2000 Referenced Documents 313FC-3000 Materials 314
34、FC-4000 Design 316FC-5000 Inspection . 322FC-6000 Fabrication 325FC-7000 Packaging, Shipping, and Storage 326FC-8000 Quality Assurance 327FC-9000 Nameplates 328FiguresFC-4100-1 Type A Metal Case Separator Filter . 317FC-4100-2 Type A Wood Case Separator Filter . 317FC-4100-3 Type B Minipleat (Glue S
35、eparator) Filter. 318viFC-4100-4 Type C Separatorless Filter . 318FC-4100-5 Type D Thread Separator Filter . 319FC-4100-6 Gel Seal Filter CornerIsometric 320TablesFC-4110 Nominal Sizes and Ratings 316FC-5100-1 Test Groups and Sequence 323FC-5120-1 Acceptable Test 323FC-5140-1 Test Conditions and Req
36、uirements . 323Mandatory AppendixFC-I Filter Media: Fire-Resistant, High Efficiency 329Nonmandatory AppendixFC-A Division of Responsibility. 338Section FD Type II Adsorber Cells 339FD-1000 Introduction 339FD-2000 Referenced Documents 340FD-3000 Materials 341FD-4000 Design 343FD-5000 Inspection and T
37、esting 345FD-6000 Fabrication 347FD-7000 Packaging and Shipping 348FD-8000 Quality Assurance 349FD-9000 Nameplates and Certification 350FigureFD-4100 Type II Adsorber Cell 344TablesFD-5332 Detector Sensitivity for Leak Test . 346FD-6100 Cell Dimensions and Tolerances . 347Mandatory AppendixFD-I Calc
38、ulation of Residence Time of Adsorber Cells . 351Nonmandatory AppendixFD-A Division of Responsibility. 352Section FE Type III Adsorbers 353FE-1000 Introduction 353FE-2000 Referenced Documents 355FE-3000 Materials 356FE-4000 Design 357FE-5000 Inspection and Testing 362FE-6000 Fabrication and Installa
39、tion 364FE-7000 Packaging and Shipping 365FE-8000 Quality Assurance 366FE-9000 Nameplates 367FigureFE-4110 Horizontal Section of Type III Adsorber Bed . 358Mandatory AppendicesFE-I Residence Time Calculation . 368FE-II Screen Waviness Inspection Test. 369FE-III Adsorber Filling Qualification Test Pr
40、ocedure . 372FE-IV Type III Adsorber Qualification Test Procedure . 378Nonmandatory AppendicesFE-A Visual Inspection Recommendations for Type III Adsorbers 385FE-B Division of Responsibility. 386viiSection FF Adsorbent Media 387FF-1000 Introduction 387FF-2000 Referenced Documents 388FF-3000 Material
41、s 389FF-4000 Design 390FF-5000 Inspection and Testing 391FF-6000 Fabrication 393FF-7000 Packaging and Shipping 394FF-8000 Quality Assurance 395FF-9000 Nameplate and Certification . 396Nonmandatory AppendixFF-A Division of Responsibility. 397Section FG Mounting Frames for Air-Cleaning Equipment 398FG
42、-1000 Introduction 398FG-2000 Referenced Documents 399FG-3000 Materials 400FG-4000 Design 401FG-5000 Inspection and Testing 407FG-6000 Fabrication 409FG-7000 Packaging and Shipping 410FG-8000 Quality Assurance 411FG-9000 Nameplates 412FiguresFG-4110-1 Typical Filter Mounting Frame 402FG-4120-1 Typic
43、al Type II Adsorber Mounting Frame . 403FG-4140-1 Typical Moisture Separator Mounting Frame 404Nonmandatory AppendixFG-A Division of Responsibility. 413Section FH Other Adsorbers 416FH-1000 Introduction 416FH-2000 Referenced Documents 417FH-3000 Materials 418FH-4000 Design 420FH-5000 Inspection and
44、Testing 425FH-6000 Fabrication 427FH-7000 Packaging and Shipping 428FH-8000 Quality Assurance 429FH-9000 Nameplates and Certification 430FiguresFH-4000-1 Type IV “V” Adsorbers Model (Fluid Seal Version). 421FH-4000-1A Type IV “V” Bed Adsorbers Model (Gasketed Version) . 422FH-4000-2 Type IV “V” Adso
45、rbers Model, Exploded View. 423FH-4000-3 Type IV “U” Bed Adsorbers Model (Gasketed Version) . 424TableFH-6100 Dimensional Requirements 427Nonmandatory AppendixFH-A Division of Responsibility. 431Section FI Metal Media Filters (In The Course of Preparation) 432Section FJ Low Efficiency Filters . 433F
46、J-1000 Introduction 433FJ-2000 Referenced Documents 434FJ-3000 Materials 435FJ-4000 Design 436viiiFJ-5000 Inspection and Testing 437FJ-6000 Fabrication 438FJ-7000 Packaging, Shipping, Receiving, Storage, and Handling 439FJ-8000 Quality Assurance 440FJ-9000 Labels and Markings . 441Nonmandatory Appen
47、dixFJ-A Division of Responsibility. 442Section FK Special HEPA Filters 443FK-1000 Introduction 443FK-2000 Referenced Documents 445FK-3000 Materials 446FK-4000 Design 448FK-5000 Qualification, Inspection, and Production Testing 458FK-6000 Fabrication 465FK-7000 Packaging, Shipping, and Storage 466FK-
48、8000 Quality Assurance 467FK-9000 Nameplates 468FiguresFK-4100-1 Type 1 Radial Flow HEPA Filter (Internal Gasket), Mid-Section View 449FK-4100-2 Type 1 Radial Flow HEPA Filter (Gelatinous Seal), Mid-Section View 450FK-4100-3 Type 1 Radial Flow HEPA Filter (External Gasket), Mid-Section View . 451FK-
49、4100-4 Type 1 Radial Flow HEPA Filter (Gelatinous Seal), Mid-Section View 452FK-4100-5 Type 2 Axial Flow Circular HEPA Filter. 453FK-4100-6 Type 2 Axial Flow Circular HEPA Filter. 454TablesFK-4000-1 Type 1 Radial Flow HEPA Filter Nominal Rating . 448FK-4000-2 Type 2 Axial Flow Circular HEPA Filter Nominal Rating 453FK-4000-3 Performance Requirements 457FK-5000-1 Test Groups and Sequence Type 1 Radial Flow HEPA Filters. 459FK-5000-2 Test Groups and Sequence Type 2 Axial Flow Circular HEPA Filters 460FK-5000-3 Test Groups and Sequence Type 4 Axial Flow Rectangular HEPA Fi
