1、 The American Society of Mechanical Engineers AN AMERICAN NATIONAL STANDARD STEEL BUSHED ROLLERLESS CHAINS SPROCKET TEETH ATTAIHMENTS, AND ASME B29.12M-1997 Revision of ANSIIASME B29.12M-1983 (R1 988)l Date of Issuance: September 1, 1997 This Standard will be revised when the Society approves the is
2、suance of a new edition. There will be no addenda or written interpretations of the re- quirements of this Standard issued to this Edition. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the
3、 criteria for American National Standards. The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public re- view and commen
4、t which provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large, ASME does not “approve,“ “rate,“ or “endorse“ any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of an
5、y patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure any- one utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume any such liability. Users of a code or standard are expressly advised that
6、the determi- nation of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representativek) or personk) affiliated with industry is not to be interpreted as government or industry endorsement of th
7、is code or standard. ASME accepts responsibility for only those interpretations issued in accordance with gov- erning ASME procedures and policies which preclude the issuance of interpretations by indi- vidual volunteers. No part of this document may be reproduced in any form, in an electronic retri
8、eval system or otherwise, without the prior written permission of the publisher. The American Society of Mechanical Engineers 345 East 47th Street, New York, NY 10017 Copyright 0 1997 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in USA. FOREWORD (This Foreword is not p
9、art of ASME B29.12M-1997.) Chains of the type covered by this Standard were introduced early in the 20th century. The chains met with considerable success on material conveyors and elevators, and manufacturers developed and marketed many sizes and types in the next several years. The American Sprock
10、et Chain Manufacturers Association (now the American Chain Association) recognized the need for standards which would provide for interchangeability by intercoupling chains of various manufacture. In November 1960, a working group of produc- ers of the bushed rollerless chains was formed to accompli
11、sh standardization. This Standard is the result of the work of that group. This Standard was presented to the USA (now ANSI) Standards Committee B29 on December 12, 1967, and, upon approval by the USA Standards Institute (now American National Standards Institute, Inc.), on October 18, 1968, was ado
12、pted and published. The 1974 revision included minor changes in metric units and the addition of caution notes to Table 1. To facilitate the use of this Standard in the international market, the metric equivalents of all dimensions are given. The current revision includes the addition of chain numbe
13、rs S-856, S-857, S-859, and S-864 and attachments K-24, K-3, K-35, K-44, and K-443 for these chains. Also added is minimum bolt hole diameter required for the bolt diameter for a particular attachment. The Minimum Ultimate Tensile Strength definition (para. 2.1) has also been modified. This revision
14、 was approved by the American National Standards Institute, Inc., on March 25, 1997. iii ASME STANDARDS COMMllTEE B29 Chains, Attachments, and Sprockets for Power Transmission and Conveying (The following is the roster of the Committee at the time of approval of this Standard.) OFFICERS C. B. Norber
15、g, Chair R. H. Uttke, Vice Chair J. L. Wright,Vice Chair K. Wessely, Secretary COMMllTEE PERSONNEL E. B. Beardslee, Beardslee Transmission Equipment Co. L. E. Hampel, Allied-Locke Industries, Inc. J. M. Lewis, Webster Industries, Inc. D. Moore, Jeffrey Chain C. E. Norberg V. D. Petershack R. A. Rein
16、fried, Conveyor Equipment Manufacturers Association K. J. Smith, Drives, Inc. R. H. Uttke, Rexnord, Inc. J. L. Wright, Diamond Chain Co. D. N. Zwiep, Worcester Polytechnic Institute J. Kana, Alternate, U.S. Tsubaki, Inc. C. McDonald, Alternate, Jervis 6. Webb Co. V . Foreword . 111 CommitteeRoster v
17、 . 1 Nomenclature 1 3 Chain Dimensions 3 2 General Chain Proportions and Designations 1 4 Attachment Dimensions 6 5 SprocketToothFo rm 14 Figures 1 Steel Bushed Rollerless Chain 2 2 Steel Bushed Rollerless Chain Nomenclature 2 3 SprocketToothForm . 14 Tables 1 General Chain Dimensions. M.U.T.S., Str
18、and Length. and 2 Maximum and Minimum Controlling Dimensions for Interchangeable MeasuringLoad . 3 ChainLinks 4 3 Chain Clearance Dimensions . 5 4 A-1 Attachment . 6 5 A-2Attachment . 7 6 A-22 Attachment 8 7 K-1 Attachment 9 8 K-2 Attachment 10 10 K-35 Attachment 12 . . 9 K-3Attachment . 11 11 K-44
19、and K-443 Attachments . 13 12 Sprockets-Maximum Eccentricity and Face Runout Tolerances 15 13 Sprocket Tooth Form Factors . 15 vii ASME 629.12M-1997 STEEL BUSHED ROLLERLESS CHAINS, ATTACHMENTS, AND SPROCKET TEETH 1 NOMENCLATURE 2.2 Measuring Load steel bushed rollerless chains: a series of block lin
20、ks The measuring load in pounds or newtons listed in having steel bushings to contact the sprocket teeth, ai- Table 1 is the load under which a dry or lightly lubri- temating with links composed of sidebars and pins which cated chain should be measured for length. articulate in the steel bushings of
21、 the block link. Pins and bushings are fixed against rotation in sidebar pitch holes by mechanical locks such as flats, interfer- ence fits, or both. 2.3 Strand Length Tolerance Assembly of pins may be from either side or alternated New chains under measuring load may be over theo- at the manufactur
22、ers option. retical length up to 0.38 in. in 120 in. (9.7 mm in 3048 See Figs. 1 and 2. mm), but must not be under the theoretical length. Maximum and minimum strand lengths for each chain are listed in Table 1. 2 GENERAL CHAIN PROPORTIONS AND DESIGNATIONS 2.4 Dimensions of Chain Links 2.1 Minimum U
23、ltimate Tensile Strength (M.U.T.S.) Minimum Ultimate Tensile Strength (M.U.T.S.) for chain covered by this Standard is the minimum force at which an unused, undamaged chain could fail when sub- jected to a single tensile loading test. WARNING: The Minimum Ultimate Tensile Strength is NOT a “work- in
24、g load!” The M.U.T.S. greatly exceeds the maximum force that may be safely applied to the chain. (a) Test Procedure: A tensile force is slowly applied, in uniaxial direction, to the ends of the chain sample. (b) The tensile test is a destructive test. Even though the chain may not visibly fail when
25、subjected to the “Minimum Ultimate Tensile Force,” it will have been damaged and will be unfit for service! To assure interchangeability of either block links or connecting links as produced by different makers of chain, standard maximum and minimum dimensions are adopted. They are not actual dimens
26、ions used in manufacturing but limiting dimensions, maximum or minimum, required to assure the desired interchange- ability. In addition to the sprocket tooth form in this Standard, these chains can operate over sprockets de- signed to ASME B29.11M-1994 or combination chains, provided consideration
27、is given to strength and addi- tional sidebar clearance required for chain sizes S 11 1 and S 150. Dimensions are given in a decimal inch system essen- tially in accordance with ANSI B87.1-1965. The metric equivalent dimensions are for reference only in ANSI 2210.1-1972. 1 ASME B29.12M-1997 STEEL BU
28、SHED ROLLERLESS CHAINS, AUACHMENTS, AND SPROCKET TEETH FIG. 1 STEEL BUSHED ROLLERLESS CHAIN V 2 STEEL BUSHED ROLLERLESS CHAINS, ATTACHMENTS, AND SPROCKET TEETH 3 CHAIN DIMENSIONS ASME B29.12M-1997 TABLE 1 GENERAL CHAIN DIMENSIONS, M.U.T.S., STRAND LENGTH, AND MEASURING LOAD Dimensions, in. Chain Num
29、ber S 102B S 110 S 111 S 131 S 150 S 188 S856 S857 S859 S864 P-Chain pitch 4.000 6.000 4.760 3.075 6.050 2.609 6.000 6.000 6.000 7.000 DPin diameter 0.625 0.625 0.750 0.625 1.000 0.500 1.000 1.000 1.250 1.250 F-Overall chain 1.50 1.50 2.00 1.50 2.50 1.12 2.50 3.25 4.00 4.00 KBushing diameter 1.00 1.
30、26 1.44 1.26 1.76 0.88 1.75 1.75 2.38 2.38 %Sidebar thickness 0.38 0.38 0.38 0.38 0.50 0.25 0.50 0.50 0.63 0.63 W-Inside width 2.13 2.13 2.63 1.32 3.32 1.06 3.00 3.00 3.75 3.75 M.U.T.S., Ib (see 2.1) 36.000 36.000 48.000 36.000 85.000 23.000 82.000 97.000 155.000 155.000 Number of pitches/ 30 20 26
31、40 20 46 20 20 20 18 height nominal 120 in. strand length of nominal 120 in. strand length of nominal 120 in. strand Max. measuring 120.38 120.38 124.14 123.38 121.38 120.39 120.38 120.38 120.38 126.38 Min. measuring 120.00 120.00 123.76 123.00 121.00 120.00 120.00 120.00 120.00 126.00 Measuring loa
32、d, Ib 300 300 500 400 800 200 800 1000 1700 1500 Dimensions, mm Chain Number S102B S 110 S111 S131 S 150 S188 S856 S857 S859 S864 f-Chain pitch DPin diameter FOverall chain KBushing diameter T-Sidebar thickness W-Inside width M.U.T.S.kN (see 2.1) Number of pitches/ nominal 3048 mrn strand length of
33、nominal 3048 mm strand length of nominal 3048 rnm strand Measuring load, kN height Max. measuring Min. measuring 101.60 15.88 38.1 25.4 9.7 54.1 160 30 3057.7 3048.0 1.3 152.40 120.90 78.11 15.88 19.05 15.88 38.1 50.8 38.1 32.0 36.6 32.0 9.7 9.7 9.7 54.1 66.8 33.5 160 214 160 20 26 40 3057.7 3153.2
34、3138.9 3048.0 3143.5 3124.2 1.3 2.2 1.8 153.67 25.40 63.5 44.7 12.7 84.3 378 20 3083.1 3073.4 3.6 66.27 152.40 12.70 25.40 28.4 63.5 22.4 44.4 6.4 12.7 26.9 76.2 102 365 46 20 3057.9 3057.7 3048.3 3048.0 0.9 3.5 152.40 152.40 177.80 25.40 31.75 31.75 82.6 101.6 101.6 44.4 60.4 60.4 12.7 16.0 16.0 76
35、.2 95.3 95.3 432 690 690 20 20 18 3057.7 3057.7 3220.0 3048.0 3048.0 3200.0 4.5 7.7 6.8 3 ASME B29.12M-1997 STEEL BUSHED ROLLERLESS CHAINS, ATTACHMENTS, AND SPROCKET TEETH TABLE 2 MAXIMUM AND MINIMUM CONTROLLING DIMENSIONS FOR INTERCHANGEABLE CHAIN LINKS Dimensions, in. Chain Number. S 1026 s 110 Sl
36、ll S 131 S 150 S 188 S856 S857 S859 S864 P-Chain pitch 4.000 DPin diameter 0.626 B-Inside diameter of 0.631 KEushing diameter 1 .oo Z-Width between 2.94 (max.) bushing (rnin.) (max.) outer sidebars (rnin.) (rnax.) between sidebars X-Width of block link . 2.92 W-Inside width 2.02 6.000 0.626 0.631 1.
37、26 2.94 2.92 2.02 4.760 0.751 0.756 1.44 3.44 3.42 2.49 3.075 0.626 0.631 1.26 2.13 2.1 1 1.25 6.050 1.001 1.006 1.76 4.40 4.38 3.15 2.609 0.501 0.506 .88 1.62 1.60 1.01 6.000 1.001 1.006 1.75 4.03 4.06 2.85 6.000 1.001 1.006 1.75 4.03 4.06 2.85 6.000 1.251 1.256 2.38 5.08 5.06 3.56 7.000 1.251 1.25
38、6 2.38 5.08 5.06 3.56 block link (rnin.) Dimensions, mm Chain Number 51028 S110 S111 S 131 S 150 S 188 S856 S857 S859 S864 P-Chain pitch 101.60 152.40 120.90 78.11 153.67 66.27 152.40 152.40 152.40 177.80 DPin diameter (rnax.) 15.87 15.87 19.13 15.87 25.43 12.73 25.43 25.43 31.77 31.77 5-Inside diam
39、eter of 16.03 16.03 19.25 16.03 25.55 12.85 25.55 25.55 31.90 31.90 /+Bushing diameter 25.40 32.50 36.60 32.50 44.70 22.40 44.45 44.45 60.45 60.45 Z-Width between 74.68 74.68 87.38 54.10 111.76 41.15 102.36 102.36 129.03 129.03 bushing (rnin.) (rnax.) outer sidebars (rnin.) (rnax.) between sidebars
40、block link (rnin.) X-Width of block link 74.17 74.17 86.87 53.59 111.25 40.64 103.12 103.12 128.52 128.52 W-Inside width 51.30 51.30 63.20 31.70 80.00 25.60 72.39 72.39 90.42 90.42 4 STEEL BUSHED ROLLERLESS CHAINS, ATTACHMENTS, AND SPROCKET TEETH ASME B29.12M-1997 TABLE 3 CHAIN CLEARANCE DIMENSIONS
41、Dimensians. in. Chain Number S 102B S 110 S 111 S 131 S 150 S 188 S856 S857 S859 S864 F-Chain height (max.) 1.56 1.56 2.06 1.56 2.62 1.18 2.62 3.37 4.09 4.09 V-Sidebar end clearance 0.94 0.94 1.34 0.94 1.78 0.67 1.40 1.90 2.38 2.38 /+Attachment clearance 0.96 0.96 1.36 0.96 1.80 0.69 1.42 1.92 2.26
42、2.26 J-Pin head to centerline 2.07 2.07 2.41 1.65 3.10 1.26 2.91 2.91 3.57 3.57 K-Pin end to centerline 2.31 2.31 2.75 1.91 3.38 1.44 3.19 3.19 3.85 3.85 radius (rnax.) radius (min.) (rnax.) fmax.) Dimensions, mm Chain Number F-Chain height (rnax.) V-Sidebar end clearance R-Attachment clearance J-Pi
43、n head to centerline K-Pin end to centerline radius (rnax.) radius (min.) (rnax.) (max.) S102B S110 S111 S 131 S150 S188 S856 S857 S859 S864 39.6 39.6 52.3 39.6 66.5 30.0 66.5 85.6 103.9 103.9 23.9 23.9 34.0 23.9 45.2 17.0 35.6 48.3 60.5 60.5 24.4 24.4 34.5 24.4 45.7 17.5 36.1 48.8 57.4 57.4 52.6 52
44、.6 61.3 41.9 78.7 32.0 73.9 73.9 90.7 90.7 58.7 58.7 69.9 48.6 85.9 36.6 81.0 81.0 97.8 97.8 5 ASME 829.12M-1997 STEEL BUSHED ROLLERLESS CHAINS, ATTACHMENTS, AND SPROCKET TEETH 4 ATTACHMENT DIMENSIONS TABLE 4 A-I ATTACHMENT Dimensions, in. Chain E. S, r. R. Bolt 0. Min. Number A B Max. H Max. Max. M
45、in. Size Hole S 102 B 2.38 2.00 3.03 1 .oo 3.56 0.41 0.96 .38 .40 S 131 2.06 1.54 2.91 1 .oo 3.09 0.41 0.96 .50 S 188 .53 1.88 1.30 2.15 0.81 2.59 0.28 0.69 .33 .a Dimensions, mm Chain E. S. r. R. Bolt 0, Min. Number A B Max. H Max. Max. Min. Size Hole S 102 B 60.5 50.8 77.0 25.4 90.4 10.4 24.4 9.7
46、10.2 S 131 52.3 39.1 73.9 25.4 78.5 10.4 24.4 12.7 13.5 S 188 47.8 33.1 54.6 20.6 65.8 7.1 17.5 9.7 10.2 NOTE: (1) For Vdimension, see Table 3. 6 STEEL BUSHED ROLLERLESS CHAINS, ATTACHMENTS, AND SPROCKET TEETH ASME B29.12M-1997 TABLE 5 A-2 AlTACHMENT Dimensions, in. Chain E. s. T. R. Bolt D, Min. Nu
47、mber A B Max. F H Max. Max. Min. Size Hole S 102 B 2.65 1.12 3.03 1.75 l.OO(3) 3.56 0.41 0.96 .38 .40 s 110 2.65 2.12 3.53 1.75 l.OO(3) 3.56 0.41 0.96 .38 .40 s 111 3.13 1.22 3.65(2) 2.31 1.50 4.15 0.41 1.36 .50 .53 S 131 2.06 0.79 2.91 1.50 l.OO(3) 3.09 0.41 0.96 .50 .53 S 150 3.75 1.66 4.28 2.75 1
48、.88 4.91 0.53 1.80 .50 .53 S 188 2.10 0.68 2.15 1.25 0.81 2.59 0.28 0.69 , .3 1 .34 Dimensions, mm Chain E. s. T. R. Bolt D, Min. Number A B Max. F H Max. Max. Min. Size Hole S 102 B 67.3 28.4 77.0 44.5 25.4(3) 90.4 10.4 24.4 9.70 10.2 s 110 67.3 53.8 89.7 44.5 25.4(3) 90.4 10.4 24.4 9.70 10.2 s 111
49、 79.5 31.0 92.7(2) 58.7 38.1 105.4 10.4 34.5 12.70 13.5 S 131 52.3 20.1 73.9 38.1 25.4(3) 78.5 10.4 24.4 12.70 13.5 S 150 95.3 42.2 108.7 69.9 47.8 124.72 13.5 45.7 12.70 13.5 S 188 53.3 17.3 54.6 31.8 20.6 65.8 7.1 17.5 7.90 10.2 NOTES: (1) For Vdimension, see Table 3. (2) 5.21 in. (132.3 mm) maximum for alternate wide A-2 attachment for S 111. Use as outer sidebar attachment only. (3) 1.12 in. (28.4 mm) maximum for alternate attachment height for S 102 6, S 110, and S 131. 7 ASME 629.12M-1997 STEEL BUSHED ROLLERLESS CHAINS, AlTACHMENTS, AND SPRO
