1、AMERICAN NATIONAL STANDARD DriII Drivers, Split - Sleeve, CoIIet Type ANSI B94.35 - 1972 REVISION OF ANSI 894.35-1959 (R1971)I REAFFIRMED 1995 FOR CURRENT COMMllTEE PERSONNEL PLEASE SEE ASME MANUAL AS1 1 THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY THE AMERICAN SOCIETY OF MECHANICAL ENG
2、INEER$ United Engineering Center 345 East 47th Street New York, N. Y. 1 001 7 Any part of this standard may be quoted. Credit lines should read: ”Extracted from American National Standard Drill Drivers-Split Sleeve, Collet Type, ANSI B94.35- 1972, with the permission of the publisher, The American S
3、ociety of Mechanical Engineers, 345 East 47th Street, New York, N.Y. 10017.” Copyright, 01972. by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed in U. S. A. FOREWORD Throughout American industry a variety of methods and mechanisms are used to drive twist drills, reamers, etc. In the automotive
4、 and other mass production industries, the split-sleeve collet drive has proven useful. Two engineering reasons for its suitability are: (1) Multiple spindle drill heads can be designed with spindles on a very close center-to-center distance; (2) Bushing plates do not have to be moved when tools mus
5、t be replaced. The splitsleeve collet driver is designed to drive straight shanks in sizes $61 (0.0390) inch diameter and larger. As the assembly of split sleeve collet-type driver necessitates manufacture to close tolerances, it was deemed advisable to develop an American standard to insure that co
6、llets would fit drill shanks as shown in ANSI 894.1 1-1967. The required ASA approval and designation as American Standard Drill Drivers was granted on September 23, 1959, and designated ASA 85.27-1959. ASA B5.27-1959 was redesignated and reaffirmed as ANSI B94.35-1959 (R1971). ANSI 894.35-1959 (R19
7、71) was reviewed in relation to industry needs and revised and updated by a subcommittee of Technical Committee 7 of American National Standards Committee 894. Sizes no longer used were eliminated from the standard. Document was reviewed for con- formance with American National Standard Decimal Inch
8、, ANSI B87.1-1965. The current revision was approved by ANSI on May 30, 1972. iii AMERICAN NATIONAL STANDARDS COMMITTEE B94 STANDARDIZATION OF CUTTING TOOLS, HOLDERS, DRIVERS 81 BUSHINGS (The following is the roster of the Committee at the time of approval of this standard) OFFICERS H.J. Moffatt, Ch
9、airman A.M. Mezey, Vice-chairman H. McLinden, Secretary STANDARDS COMMITTEE AMERICAN GEAR MANUFACTURERS ASSOCIATION, THE P.M. Dean, Jr., Mechanical Technology, Inc., Latham, New York G.L. Scott, Alternate, American Gear Manufacturers Association, Washington, D.C. AMERICAN SOCIETY OF MECHANICAL ENGIN
10、EERS, THE M.E. Merchant, Cincinnati Milacron, Inc., Cincinnati, Ohio G.M. Monacelli, General Electric Company, Detroit, Michigan C.J. Oxford, Jr., National Twist Drill TANDARC TAPER NUMBER 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Table 2 Dimensions of Drivers (contin
11、ued) IPTIONAL TAPER NUMBER 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 IPTIONAI NUMBER TAPER 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ,. DIAMETER INSIDE A I XI DEPTH B ENTERS DRILL DRIVER 0.1945 0.2016 0.2005 0.1995 0.1985 0.1975 0.1955 0.2035 0.2025 0.2026 0.2040 0.2205
12、 0.2195 0.2183 0.2173 0.21 25 0.21 15 0.2085 0.2075 0.2050 0.2229 0.2329 0.2335 0.2325 0.2275 0.2265 0.2239 0.2375 0.2365 0.2339 0.2387 0.2485 0.2455 0.2445 0.241 5 0.2405 0.2397 0.2510 0.2500 0.2495 0.2550 0.2700 0.2646 0.2636 0.2600 0.2590 0.2560 0.2760 0.2750 0.271 0 0.2792 0.2940 0.2930 0.2903 0
13、.2893 0.2890 0.2880 0.2844 0.2834 0.2802 0.2949 0.3105 0.3061 0.3051 0.301 0 0.3000 0.2959 0.31 50 0.3140 0.3115 0.321 0 0.3271 0.3261 0.3220 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 1 .oo 1 .oo 1 .oo 1 .oo 1 .oo 1 .oo 1 .oo 1 .oo 1 .oo 1 .oo 1 .
14、oo 1 .oo 1 .oo 1 .oo 1 .oo 1.12 1.12 1.12 5 D INSIDE DIAMETER LENGTH 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.69 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.78 0.88 0.88 0.88 T TANG SLOT E WIDTH - MIN - 0.1 34 0.134 0.134
15、 0.1 34 0.1 34 0.134 0.134 0.1 34 0.1 34 0.1 34 0.134 0.1 34 0.1 34 0.134 0.1 34 0.1 34 0.1 34 0.134 D.134 0.1 74 0.1 74 0.1 74 0.1 74 0.1 74 0.1 74 D.174 0.174 D.174 D.174 D.174 D.174 D.174 3.1 74 1.1 74 3.21 5 1.215 3.21 5 - - MAX - 0.138 a138 0.138 0.138 0.1 38 0.138 0.138 0.138 0.138 0.138 0.138
16、 0.138 a138 0.1 38 0.138 0.138 0.138 0.138 0.138 0.178 a1 78 0.1 78 0.1 78 0.178 0.178 0.178 0.178 0.1 78 0.178 0.1 78 0.178 0.1 78 0.1 78 0.1 78 0.219 0.219 0.219 - All dlmenslons are In Inches. AMERICAN NATIONAL STANDARD DRILL DRIVER-SPLIT SLEEVE. COLLET TYPE ANSI 894.35-1972 DRIVER SIZE SIZE . Q
17、R 11/32 S 9.0“ T 23/64 U 3/8 W 25/64 X Y 13/32 z 27/64 7/16 29/64 15/32 31 /64 1/2 33/64 17/32 35/64 9/16 37/64 19/32 39/64 518 41 /64 21/32 43/64 11/16 45/64 23/32 47/64 3/4 3ECIMAI . 0.3320 0.3390 0.3438 0.3480 0.3543 0.3580 0.3594 0.3680 0.3750 0.3860 0.3906 0.3970 0.4040 0.4062 0.4130 0.421 9 0.
18、4375 0.4531 0.4688 0.4844 0.5000 0.51 56 0.5312 0.5469 0.5625 0.5781 0.5938 0.6094 0.6250 0.6406 0.6562 0.6719 0.6875 0.703 1 0.7188 0.7344 0.7500 -. r STANDARI: TAPE43 NUMBER 1 1 . 1 . 1 . 1 1 . 1k 1 2“ 2 2 2; 2 2 2 2 2 2 21 2 2 2 2 2 3. 3 3 3 3 3 3; 3 3 . 3 3 . 3 Table 2 Dimensions of Drivers (con
19、cluded) OPTIONAL TAPER NUMBER 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 OPTIONAL TAPER NUMBER DIAMETER INSIDE A MIN . 0.3300 0.3370 0.3418 0.3460 0.3523 0.3560 0.3574 0.3660 0.3730 0.3840 0.3886 0.3950 0.4020 0.4042 0.41 10 0.41 99 0.4355 0.451 1 0.4668 0.4824 0.4980
20、0.51 56 0.5312 0.5469 0.5625 0.5781 0.5938 0.6094 0.6250 0.6406 0.6562 0.6719 0.6875 0.7031 0.7188 0.7344 3.7500 . MAX . 0.331 a 0.3428 0.338C 0.3470 0.3533 0.3570 0.3584 0.3670 0.3740 0.3850 0.3896 0.3960 0.4030 0.4052 0.41 20 0.4209 0.4365 0.4521 0.4678 0.4834 0.4990 0.5166 0.5322 0.5479 0.5635 0.
21、5791 0.5948 0.6 104 0.6260 0.6416 0.6572 0.6729 0.6885 3.7041 3.7198 3.7354 1.7510 7 DEPTH B DRILL ENTERS DRIVER 1.12 1.12 1.12 1.12 1.12 1.12 1.12 1.12 1.12 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.31 1.31 1.31 1.31 1.31 1.31 1.47 1.47 1.47 1.47 1.47 1.47 1.62 1.62 1.62 1.62 1.62 1.62 D
22、INSIDE DIAMETER LENGTH 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 1.03 1.03 1.03 1.03 1.03 1.03 1.12 1.12 1.12 1.12 1.12 1.12 TANG SLOT E WIDTH MIN . 0.21 5 0.21 5 0.215 0.21 5 0.215 0.21 5 0.21 5 0.21 5 0.21 5 0.255 0
23、.255 0.255 0.255 0.255 0.255 0.255 0.255 0.255 0.255 0.31 7 0.31 7 0.31 7 0.317 0.317 0.317 3.387 1.387 1.387 1.387 1.387 1.387 1.457 1.457 1.457 1.457 1.457 1.457 MAX . 0.219 0.219 0.219 0.219 0.219 0.219 0.219 0.219 0.219 0.259 0.259 0.259 0.259 11259 0.259 0.259 0.259 0.259 a259 0.323 0.323 0.323
24、 0.323 0.323 0.323 0.393 0.393 0.393 0.393 0.393 0.393 0.463 0.463 0.463 0.463 0.463 D.463 All dlmenslons are In Inches . . 6 AMERICAN NATIONAL STANDARDS FOR MACHINE TOOLS AND CUTTING TOOLS T.Slots. Their Bolts. Nuts. Tongues. and Cutters 65.1-1949 Rotating Air Cylinders and Adapters . 65.5-1959 Spi
25、ndle Noses for Tool Room Lathes. Engine Lathes. Turret Lathes. and Automatic Lathes . 65.9-1967 Chucks and Chuck Jews 65.8-1972 Machine Tapers . 65.10-1 963 Spindle Noses and Adjustable Adapters for Multiple Spindle Drilling Heads 85.11-1964 Accuracy of Engine and Tool Room Lathes 65.16-1952 (Reaffi
26、rmed 1972) Spindle Noses and Arbors for Milling Machines . 65.18-1960 Machine Pins 65.20-1958 DieSeh . 65.25-1968 Mounting Dimensions of Lubricating and Coolant Pumps for Machine Tools 85.28-1971 Designation and Working Ranges of Grinding Machines 65.32-1953 External Cylindrical Grinding Machines -
27、Plain . (Rev . 65.33-1953) 65.33-1970 Machine Mounting Specifications for Abrasive Discs and Plate Mounted Wheels 65.35-1969 External Cylindrical Grinding Machines - Centerless . 65.37-1970 Spindle Noses and Tool Shanks for Horizontal Boring Machines . 85.40-1968 Quill Flanges and Spindle Ends for U
28、pright and Horizontal Drill Spindles for Production Type Drilling Machines 65.41-1968 External Cylindrical Grinding Machines - Universal 65.42-1970 Modular Machine Tool Standards 65.43-1971 Rotary Table Surface Grinding Machines 65.44-1971 Milling Machines 65.45-1972 Symbols For Machine Tool Indicat
29、or Plates 65.46-1972 Blanks and Semi-Finished Blanks for Solid Carbide Taps . 694.1-1969 Reamers . 694.2-1971 Straight Cut-Off Blades for Lathes and Screw Machines 694.3-1965 Identification System for Throw Away Inserts for Cutting Tools 694.4-1965 Carbide Blanks and Cutting Tools 694.5-1966 Knurlin
30、g . 694.6-1966 Hobs . 694.7-1966 Inserted Blade Milling Cutter Bodies (Rev . 65.23-1958) 694.6-1967 High-speed Steel and Cast Nonferrous Single-Point Tools and Tool Holders (Rev . 65.29-1959) 694.10-1967 Twist Drills . (Rev . 65.12-1958) 694.11-1967 Masonry Drills (Rev . 682.1-1962) 694.12-1968 Blan
31、ks for Carbide Burs (Rev . 683.1-1962) 694.13-1968 Taps-Cut and Ground Threads 694.9-1971 Carbide-Tipped Masonry Drills. and Blanks for Carbide-Tipped Punches-Basic Head Type . 694.14-1968 Retainers - Basic Ball-Lock Punch and Die Button. Light and Heavy Duty 694.16-1968 Gages - Functional. Ball-Loc
32、k Punch and Die Button; Light and Heavy Duty . 694.17-1968 Punches - Basic Ball-Lock Light and Heavy Duty . : . 694.18-1968 Milling. Cutters and End Mills . (Rev . 65.3-1960) 694.19-1968 Specifications for Carbide Blanks for Twist Drills. Reamers. End Mills. and Random Rod (Rev . 685.1-1963) 694.20-
33、1968 Gear Shaper Cutters 894.21-1968 Punches-Variable Head Type . 694.22-1968 Punch Guide Bushings-Variable Press Fit 694.23-1969 Heavy Duty Carbide Inserts for Cutting Tools . 894.24-1969 Indexable (Throw-Away) Inserts for Cutting Tools (Partial Rev . 680.1-1959) 694.25-1969 Indexable (Throw-Away)
34、Insert Holders (Partial Rev . 680.1-1959) 694.26-1969 Die Buttons - Basic Taper Relief. Press Fit . 694.27-1970 Die Buttons - Basic Straight Relief. Press Fit 694.28-1970 Die Buttons - Basic Ball-Lock 694.29-1970 Die Buttons - Variable. Press Fit 694.30-1970 Steel Rotary Slitting Knives and Steel Sp
35、acing Collars . 694.31-1969 Circular and Dovetailed Forming Tools Blanks . (Redesignation of 85.7-1954) 694.32-1954 (Reaffirmed 1971) Jig Bushings . (Redesignation of 65.6-1962) 694.33-1962 (Reaffirmed 1971) Life Tests of Single Point Tools . (Redesignation of 65.19-1946) 694.34-1946 (Reaffirmed 197
36、1) Drill Drivers. Split.Sleeve. Collet Type 694.35-1972 Life Tests for Single-Point Tools of Sintered Carbide (Redesignation of 65.34-1956) 694.36-1956 (Reaffirmed 1971) Carbide Blanks and Cuttina Tools . sinale-Point Carbide.Tipped. Roller Turner Type (Revis . Binders for holding standards are avai A complete list of Standards published by The American Society of Mecl J00030
