1、Designation: A562/A562M 10Standard Specification forPressure Vessel Plates, Carbon Steel, Manganese-Titaniumfor Glass or Diffused Metallic Coatings1This standard is issued under the fixed designation A562/A562M; the number immediately following the designation indicates the yearof original adoption
2、or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers titanium-bearing carbon steelplates intended for w
3、elded glass lined pressure vessels or otherapplications where the presence of free-iron carbide would bedeleterious to the coating.Aminimum specific ratio of titaniumto carbon is specified.1.2 The maximum thickness of plates is limited to 2 in. 50mm.1.3 The values stated in either inch-pound units o
4、r SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with th
5、e specifi-cation.2. Referenced Documents2.1 ASTM Standards:3A20/A20M Specification for General Requirements forSteel Plates for Pressure Vessels3. General Requirements and Ordering Information3.1 Material supplied to this material specification shallconform to Specification A20/A20M. These requireme
6、nts out-line the testing and retesting methods and procedures, permit-ted variations in dimensions, and mass, quality and repair ofdefects, marking, loading, and ordering information.3.2 In addition to the basic requirements of this specifica-tion, certain supplementary requirements are available wh
7、enadditional control, testing, or examination is required to meetend use requirements.3.3 If the requirements of this specification are in conflictwith the requirements of Specification A20/A20M, the require-ments of this specification shall prevail.4. Manufacture4.1 Steelmaking PracticeThe steel sh
8、all be killed.5. Heat Treatment5.1 Plates shall be thermally treated to produce grain refine-ment, either by normalizing or heating uniformly for hotforming at a minimum temperature of 1600F 870C or somehigher agreed temperature, and held at this temperature for aminimum of 1 h/in. 2.4 min/mm of thi
9、ckness.6. Chemical Requirements6.1 The steel shall conform to the chemical requirementsshown in Table 1 unless otherwise modified in accordance withSupplementary Requirement S17, Vacuum Carbon-DeoxidizedSteel, in Specification A20/A20M.7. Mechanical Requirements7.1 Tension Test RequirementsThe mater
10、ial as representedby the tension-test specimens shall conform to the require-ments shown in Table 2.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and P
11、ressure Vessels.Current edition approved Oct. 1, 2010. Published November 2010. Originallyapproved in 1966. Last previous edition approved in 2006 as A562/A562M 06.DOI: 10.1520/A0562_A0562M-10.2For ASME Boiler and Pressure Vessel Code applications, see related Specifi-cation SA-562/SA-562M in Sectio
12、n II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at t
13、he end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.SUPPLEMENTARY REQUIREMENTSSupplementary requirements shall not apply unless specified in the order.Alist of standardized supplementary requirements for use at the
14、 option of the purchaser are includedin Specification A20/A20M. Those which are considered suitable for use with this specification arelisted below by title.S1. Vacuum Treatment,S2. Product Analysis,S3. Simulated Post-Weld Heat Treatment of MechanicalTest Coupons,S4. Additional Tension Test,S5. Char
15、py V-Notch Impact Test,S6. Drop Weight Test (for Material 0.625 in. 16 mm andover in Thickness),S7. High-temperature Tension Test,S8. Ultrasonic Examination in accordance with Specifica-tion A435/A435M,S9. Magnetic Particle Examination,S11. Ultrasonic Examination in accordance with Specifica-tion A5
16、77/A577M,S12. Ultrasonic Examination in accordance with Specifica-tion A578/A578M, andS17. Vacuum Carbon-Deoxidized Steel.SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue(A562/A562M 06) that may impact the use of this standard.(1)
17、Revised Section 3.(2) Revised Table 1.TABLE 1 Chemical RequirementsElementComposition,%Carbon, maxA0.12Manganese, maxHeat analysis 1.20Product analysis 1.30Phosphorus, maxA0.025Sulfur, maxA0.025SiliconA0.150.50Copper, maxA0.15Titanium, min 4 3 CAApplies to both heat and product analyses.TABLE 2 Tens
18、ile Requirementsksi MPaTensile strength 5575 380515Yield strength, min 30 205Elongation in 8 in. 200 mm min, %A22Elongation in 2 in. 50 mm min, %A26ASee Specification A20/A20M for elongation adjustments.A562/A562M 102ASTM International takes no position respecting the validity of any patent rights a
19、sserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time
20、 by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will re
21、ceive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM In
22、ternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A562/A562M 103
