ASTM B263 B263M-2004(2010)e1 Standard Test Method for Determination of Cross-Sectional Area of Stranded Conductors《绞合导体横断面积测定的标准试验方法》.pdf
《ASTM B263 B263M-2004(2010)e1 Standard Test Method for Determination of Cross-Sectional Area of Stranded Conductors《绞合导体横断面积测定的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM B263 B263M-2004(2010)e1 Standard Test Method for Determination of Cross-Sectional Area of Stranded Conductors《绞合导体横断面积测定的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B263/B263M 04 (Reapproved 2010)1Standard Test Method forDetermination of Cross-Sectional Area of StrandedConductors1This standard is issued under the fixed designation B263/B263M; the number immediately following the designation indicates the yearof original adoption or, in the case of
2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTEDesignation was correc
3、ted editorially in October 2013.1. Scope1.1 This test method covers the procedure for determiningthe cross-sectional area of stranded conductors by the massmethod.1.2 The values stated in inch-pound or SI units are to beregarded separately as the standard. The values in each systemare not exact equi
4、valents; therefore, each system shall be usedindependently of the other. Combining values from the twosystems may result in nonconformance with the specification.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the u
5、ser of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents form a part of this test methodto the extent referenced herein.2.2 ASTM Standards:2B830 Specification
6、for Uniform Test Methods and Fre-quency3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 lot, na lot is any amount of stranded conductor ofone type and size presented for acceptance at one time.3.1.2 sample, na sample is a quantity of production units(reels, spools, coils, and s
7、o forth) selected at random from thelot for the purpose of determining conformance of the lot to therequirements of this test method.3.1.3 specimen, na specimen is a length of strandedconductor removed for test purposes from any individualproduction unit of the sample.4. Apparatus4.1 Balance, for me
8、asurement of mass, accurate to 0.1 %.4.2 Steel Scale, for measurement of length, with smallestdivisions not greater than132 in. 1 mm.4.3 Jig, or equivalent equipment, for cutting the conductorto length and at right angles to its axis.5. Sampling5.1 Samples shall be taken from the outer end of reel o
9、rspool lengths, or from either end of coiled lengths.5.2 Unless otherwise specified by the purchaser at the timeof placing the order, a sample shall consist of the number ofproduction units (reels or coils) shown in Table 1 or inaccordance with Specification B830.6. Test Specimens6.1 The length of t
10、est specimens shall be as follows:Nominal Size of Test Specimen,cmil mm2Length of Test Specimen min,ft mmUp to 17 000 9, inclOver 17 000 94 12202 6107. Procedure7.1 Cut the test specimen, making sure that the ends are atthe right angles to the axis of the conductor.7.2 Measure the length of the spec
11、imen at room temperature(see Note) to the nearest132 in. 1 mm, and measure the massto within 60.1 %, converting to pounds grams if weighed inother units.NOTE 1Correction for temperature variation need not be made, sincethe error introduced in the length measurement by the temperaturevariation is les
12、s than the required accuracy of the length measurement.1This test method is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.02 onMethods of Test and Sampling Procedure.Current edition approved Oct. 1, 2010. Published December
13、2010. Originallyapproved in 1956. Last previous edition approved in 2004 as B263 04. DOI:10.1520/B0263_B0263M-04R10E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer
14、to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States18. Calculation8.1 Calculate the cross-sectional area of a strandedconductor, composed of only one type of conducting material,as
15、 follows:A 5 1000/L! 3 100/1001k!# 3 W/f!where:A = cross-sectional area, cmil mm2,W = mass of test specimen, lb g,L = length of test specimen, ft mm,f = mass factor, lb/cmil1000 ft g/cm3, (Table 2), andk = increment (increase) of weight and electrical resistance(from product specifications), %.8.2 C
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB263B263M20042010E1STANDARDTESTMETHODFORDETERMINATIONOFCROSSSECTIONALAREAOFSTRANDEDCONDUCTORS 导体

链接地址:http://www.mydoc123.com/p-460798.html