1、Designation: B 908 03Standard Practice for theUse of Color Codes for Zinc Casting Alloy Ingot1This standard is issued under the fixed designation B 908; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n
2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This standard is published with the following objectives:1.2 To establish standard color codes for the Zinc DieCasting and Foundry ind
3、ustry, and1.3 To standardize the use and application of these colorcodes.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the
4、 appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect
5、 on dateof order acceptance form a part of this specification to theextent referenced herein:2.2 ASTM Standards:B 240 Standard Specification for Zinc and Zinc-Aluminum(ZA) Alloys in Ingot Form for Foundry and Die Castings2B 275 Practice for Codification of Certain Nonferrous Met-als and Alloys, Cast
6、 and Wrought3B 327 Standard Specification for Master Alloys Used inMaking Zinc Die Casting Alloys2B 792 Standard Specification for Zinc Alloys in Ingot Formfor Slush Casting2B 793 Standard Specification for Zinc Casting Alloy Ingotfor Sheet Metal Forming Dies and Plastic Injection Molds2B 892 Standa
7、rd Specification for Zinc-Copper-AluminumAlloys in Ingot Form for Die Castings2B 899 Terminology Relating to Non-ferrous Metals andAlloys2E 527 Practice for Numbering Metals and Alloys (UNS)42.3 ISO Standard:ISO 301, Zinc alloy ingots intended for casting, 1981-05-1552.4 CEN Standard:EN 1774, Zinc a
8、nd zinc alloysAlloys for foundrypurposesIngot and liquid, September 199763. Terminology3.1 Terms shall be defined in accordance with TerminologyB 899.4. Significance and Use4.1 The purpose of these color codes is to allow for quickidentification of ingot bundles or jumbo ingots of zinc castingalloys
9、. Other than jumbo ingots, this standard is not intended toimply that each ingot will be color-coded but only that eachingot bundle be color coded.4.2 Each ingot bundle or jumbo ingot shall be identifiedwith the appropriate color code listed in Table 1.4.3 The color will be applied as a stripe, or s
10、tripes, on twoadjacent sides of the ingot bundle or jumbo ingot. The colorstripes will be applied to include the ingot bundle foot.4.4 When using multiple stripes, the colored stripes will beapplied from left to right as indicated in Table 1.4.5 In the absence of a written agreement to the contraryb
11、etween the supplier and end user, the North American colorcode will be the standard for all North American transactions;for all other transactions the International Color Code will beused.5. Keywords5.1 ACuZinc; ACuZinc5; color; color code; Kirksite; Kirk-site A; Kirksite B; non-ferrous metals; Zama
12、k; Zamak 2;Zamak 3; Zamak 5; Zamak 7; zinc; zinc alloys; zinc-aluminumalloys; zinc-copper-aluminum alloys1This practice is under the jurisdiction of ASTM Committee B02 on NonferrousMetals and Alloys and is the direct responsibility of Subcommittee B02.04 on Zincand Cadmium.Current edition approved J
13、une 10, 2003. Published August 2003. Originallyapproved in 2000. Last previous edition approved in 2000 as B 908 - 00.2Annual Book of ASTM Standards, Vol. 02.04.3Annual Book of ASTM Standards, Vol 02.02.4Annual Book of ASTM Standards, Vol. 01.01.5“English Version” available from American National St
14、andards Institute(ANSI), 11 West 42ndSt. New York, NY 10036.6“English Version” available from Global Engineering Documents, 15 InvernessWay East, Englewood, Colorado, 80112.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box
15、C700, West Conshohocken, PA 19428-2959, United States.SUMMARY OF CHANGESCommittee B02 has identified the location of selected changes to this standard since the last issue (B 908 - 00)that may impact the use of this standard.(1) Traditional names of alloys listed in Table 1. (2) Footnote F added to
16、Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rig
17、hts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional
18、 standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM
19、 Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
20、address or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Color CodesCommon UNSAASTMStandardASTMAlloyTraditionalColor CodeNorth AmericaBInternationalAlloy 3 Z33521 B 240 AG 40ACZamak 3 None White/YellowDAlloy 7 Z33522 B 240
21、 AG 40BCZamak 7 Brown White/BrownEAlloy 5 Z35530 B 240 AC 41ACZamak 5 Black White/BlackDAlloy 2 Z35540 B 240 AC 43ACZamak 2 Green White/GreenDZA-8 Z35635 B 240 ZA-8 ZA-8 Blue White/BlueDZA-12 Z35630 B 240 ZA-12 ZA-12 Orange White/OrangeDZA-27 Z35840 B 240 ZA-27 ZA-27 Purple White/PurpleDACuZinc 5 Z4
22、6540 B 892 Zn-Cu5-AI3 ACuZinc5FRed White/RedEV12 Z33730 B 327 V12 V12 Pink White/PinkESlush Casting Alloy A Z34510 B 792 Slush Casting Alloy A Slush Casting Alloy A Black/Red White/Black/RedESlush Casting Alloy B Z30500 B 792 Slush Casting Alloy B Slush Casting Alloy B Black/Orange White/Black/Orang
23、eEZinc Casting Alloy for Dies and Molds - A Z35543 B 793 Die & Mold Alloy A Kirksite A Green/Red White/Green/RedEZinc Casting Alloy for Dies and Molds - B Z35542 B 793 Die & Mold Alloy B Kirksite B Green/Black White/Green/BlackEAUNS assignations were established in accordance with Practice E 527. Th
24、e last digit of a UNS number differentiates between alloys of similar composition.BThe North American system is design to be a simplified version of the International system by eliminating the leading white stripe and in the case of Alloy 3 eliminatingall stripes.CASTM alloy designations established
25、 in accordance with Practice B 275.DThe color codes for these alloys are adapted from European standard (CEN) specification EN 1774. No color coding currently exists in International standard ISO 301.EThese alloys are not currently included in European standard EN 1774 nor International standard ISO 301 and no color codes have previously been assigned.FACuZinc and ACuZinc5 are registered names of the General Motors Corporation.B908032
