ASTM B983-2015 Standard Specification for Precipitation Hardened or Cold Worked Seamless Nickel Alloy Pipe and Tube《沉淀硬化或者冷加工无缝镍合金管的标准规格》.pdf
《ASTM B983-2015 Standard Specification for Precipitation Hardened or Cold Worked Seamless Nickel Alloy Pipe and Tube《沉淀硬化或者冷加工无缝镍合金管的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B983-2015 Standard Specification for Precipitation Hardened or Cold Worked Seamless Nickel Alloy Pipe and Tube《沉淀硬化或者冷加工无缝镍合金管的标准规格》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B983 13aB983 15Standard Specification forPrecipitation Hardened or Cold Worked, Seamless NickelAlloy Pipe and Tube1This standard is issued under the fixed designation B983; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisio
2、n, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N077
3、25, UNS N07740,UNS N09945, UNS N09925, UNS N07718, UNS N10276, UNS N06985)2 as shown in Table 1.1.2 Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plusprecipitation hardened and descaled conditions. When atmosphere control is used,
4、descaling is not necessary.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the
5、 safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety DataSheet (MSDS)(SDS) for this product/material as provided by the manufacturer, to establish appr
6、opriate safety and health practices,and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3B829 Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and TubeB899 Terminology Relating to Non-ferrous Metals and All
7、oysE8 Test Methods for Tension Testing of Metallic MaterialsE527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)3. Terminology3.1 Terms shall be defined in accordance with Terminology B899.3.2 Definitions of Terms Specific to This Standard:3.2.1 average diameter, nSee
8、Terminology B899.3.2.2 pipe, nSee Terminology B899 and Specification B829.3.2.3 tube, nSee Terminology B899.4. General Requirements4.1 Material furnished under this specification shall conform to the applicable requirements of Specification B829 unlessotherwise provided herein.5. Ordering Informatio
9、n5.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the material ordered under thisspecification. Examples of such requirements include, but are not limited to the following:5.1.1 AlloyTable 1.1 This specification is under the jurisdiction ofASTM Committ
10、ee B02 on Nonferrous Metals andAlloys and is the direct responsibility of Subcommittee B02.07 on RefinedNickel and Cobalt and Their Alloys.Current edition approved Oct. 1, 2013Oct. 1, 2015. Published October 2013October 2015. Originally approved in 2012. Last previous edition approved in 2013 as B98
11、3 13.13a. DOI: 10.1520/B0983-13A.10.1520/B0983-15.2 New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For
12、Annual Book of ASTM Standardsvolume information, refer to the standardsstandards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becausei
13、t may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears a
14、t the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.1.1 Heat Treatment or Cold Work or Type (Table 2 and Table 3.)5.1.2 Dimensions:5.1.2.1 TubeOutside diameter, minimum or average wall thickness, and length.5
15、.1.2.2 PipeStandard pipe size and schedule (Specification B829).5.1.3 EndsPlain ends cut and deburred will be furnished.5.1.4 CertificationState if certification or a report of test results is required (Section 16).5.1.5 Samples for Check AnalysisState whether samples for check analysis should be fu
16、rnished.5.1.6 Purchaser InspectionIf the purchaser wishes to witness tests or inspection of material at the place of manufacture, thepurchase order must so state, indicating which tests or inspections are to be witnessed (Section 15).6. Chemical Composition6.1 The material shall conform to the compo
17、sition limits specified in Table 1.6.2 If a product (check) analysis is made by the purchaser, the material shall conform to the requirements specified in Table 1subject to the permissible tolerances per Specification B829.7. Mechanical Properties7.1 Unless otherwise specified, the material shall be
18、 supplied in the cold worked (cw), or cold worked and precipitationhardened (prec hard), or solution annealed plus precipitation hardened condition as described in Table 2 and Table 3.7.2 The mechanical properties of the material at room temperature shall conform to those shown in Table 3.8. Hydrost
19、atic Test or Non-Destructive Electric Test8.1 Each pipe or tube shall be tested by the manufacturer by either hydrostatic or a non-destructive electric test in accordancewith Specification B829. Hydrostatic testing at a pressure greater than 1000 psi may be performed upon agreement between thepurcha
20、ser and manufacturer or at the option of the manufacturer provided that the allowable fiber stress per Specification B829is not exceeded.9. Weight9.1 For calculation of mass or weight, the following densities shall be tested:Alloy Densitylb/in.3 g/cm3UNS N07022 0.311 8.60UNS N07725 0.300 8.31UNS N07
21、740 0.291 8.05UNS N09945 0.296 8.2UNS N09925 0.292 8.08UNS N07718 0.296 8.19UNS N10276 0.321 8.89TABLE 1 Chemical RequirementsElement UNSN07022 UNSN07725 UNSN07740 UNSN09945 UNSN09925 UNSN07718 UNSN10276 UNSN06985Carbon 0.010 max 0.03 max 0.005-0.08 0.005-0.04 0.03 max 0.08 max 0.02 max 0.015 maxMan
22、ganese 0.5 max 0.35 max 1.0 max 1.0 max 1.00 max 0.35 max 1.0 max 1.0 maxSilicon 0.08 max 0.20 max 1.0 max 0.5 max 0.50 max 0.35 max 0.08 max 1.0 maxPhosphorous 0.025 max 0.015 max 0.03 max 0.03 max . 0.015 max 0.030 max 0.04 maxSulfur 0.015 max 0.010 max 0.03 max 0.03 max 0.030 max 0.015 max 0.030
23、max 0.03 maxChromium 20.0-21.4 19.0-22.5 23.5-25.5 19.5-23.0 19.5-23.5 17.0-21.0 14.5-16.5 21.0-23.5Cobalt 1.0 max . 15.0-22.0 . . 1.0 max 2.5 max 5.0 maxMolybdenum 15.5-17.4 7.00-9.50 2.0 max 3.0-4.0 2.50-3.50 2.80-3.30 15.0-17.0 6.0-8.0Columbium . 2.75-4.00 . 2.4-4.5 0.50 max 4.75-5.50 . .Titanium
24、 . 1.00-1.70 0.5-2.5 0.5-2.5 1.90-2.40 0.65-1.15 . .Aluminum 0.5 max 0.35 max 0.2-2.0 0.01-0.7 0.10-0.50 2.20-0.80 . .Zirconium . . . . . . . .Boron 0.006 max . 0.00060.006 . . 0.006 max . .Iron 1.8 max RemainderB 3.0 max RemainderB 22.0 minA RemainderB 4.0-7.0 18.0-21.0Copper 0.5 max . 0.50 max 1.5
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB9832015STANDARDSPECIFICATIONFORPRECIPITATIONHARDENEDORCOLDWORKEDSEAMLESSNICKELALLOYPIPEANDTUBE 沉淀

链接地址:http://www.mydoc123.com/p-462992.html