ASTM C1321-2009 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction《建筑物内部辐射控制涂层系统(IRCCS)的安装和使用的标准实施规程》.pdf

上传人:sofeeling205 文档编号:464219 上传时间:2018-11-27 格式:PDF 页数:3 大小:74.20KB
下载 相关 举报
ASTM C1321-2009 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction《建筑物内部辐射控制涂层系统(IRCCS)的安装和使用的标准实施规程》.pdf_第1页
第1页 / 共3页
ASTM C1321-2009 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction《建筑物内部辐射控制涂层系统(IRCCS)的安装和使用的标准实施规程》.pdf_第2页
第2页 / 共3页
ASTM C1321-2009 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction《建筑物内部辐射控制涂层系统(IRCCS)的安装和使用的标准实施规程》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation: C1321 09Standard Practice forInstallation and Use of Interior Radiation Control CoatingSystems (IRCCS) in Building Construction1This standard is issued under the fixed designation C1321; the number immediately following the designation indicates the year oforiginal adoption or, in the c

2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice has been prepared for use by the designer,specifier, and applicator of IRCC

3、S (Interior Radiation ControlCoating Systems) for use in building construction. The scope islimited to recommendations related to the use and installationof IRCCS, including a surface(s) having a far-infrared emit-tance of 0.25 or less that is sprayed or painted.2Some examplesthat this practice is i

4、ntended to address include: (1) lowemittance surfaces in vented building envelope cavities in-tended to retard radiant transfer across the vented airspace; (2)low emittance surfaces at interior building surfaces intended toretard radiant transfer to or from building inhabitants; and (3)low emittance

5、 surfaces at interior building surfaces intended toreduce radiant transfer to or from heating or cooling systems.See Fig. 1 and Fig. 2 for typical applications.1.2 This practice covers the installation process from pre-installation inspection through post-installation. It does notcover the productio

6、n of the Interior Radiation Control CoatingMaterials.1.3 This practice is not intended to replace the manufactur-ers installation instructions, but it shall be used in conjunctionwith such instructions. This practice is not intended to super-sede local, state, or federal codes.1.4 This practice assu

7、mes that the installer possesses a goodworking knowledge of the application codes and regulations,safety practices, tools, equipment, and methods necessary forthe installation of Interior Coating Materials. It also assumesthat the installer understands the fundamentals of buildingconstruction that a

8、ffect the installation of an IRCCS.1.5 When the installation or use of Interior RadiationControl Coating Materials, accessories, and systems posesafety or health problems, the manufacturer shall provide theuser appropriate current information regarding any knownproblems associated with the recommend

9、ed use of the compa-nys products and shall also recommend protective measures tobe employed in their safe utilization. The user shall establishappropriate safety and health practices and determine theapplicability of regulatory requirements prior to use.1.6 This standard does not purport to address

10、all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific precau-tionary statements are contained in Sections

11、 5 and 7.2. Referenced Documents2.1 ASTM Standards:C168 Terminology Relating to Thermal InsulationC1371 Test Method for Determination of Emittance ofMaterials Near Room Temperature Using Portable Emis-sometersE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE96/E96M Test Metho

12、ds for Water Vapor Transmission ofMaterials2.2 NFPA Standards:3NFPA 54 National Fuel Gas CodeNFPA 211 Standard for Chimneys, Fireplaces and Vents2.3 Other Documents:CPSC Product Safety Fact Sheet No. 18 “The Home Elec-trical System”43. Terminology3.1 DefinitionsFor definitions of terms used in this

13、prac-tice, refer to Terminology C168.3.2 Definitions of Terms Specific to This Standard:3.2.1 applicatorthe person or persons who apply interiorreflective coating materials in buildings.3.2.2 conditioned spaceany space in a building that isserved by a heating or cooling system.3.2.3 Interior Radiati

14、on Control Coating Systems(IRCCS)a building construction consisting of a low emit-tance (0.25 or less) surface bounded by an open air space. An1This practice is under the jurisdiction of ASTM Committee C16 on ThermalInsulation and is the direct responsibility of Subcommittee C16.21 on ReflectiveInsu

15、lation.Current edition approved Nov. 1, 2009. Published December 2009. Originallyapproved 1996. Last previous edition approved in 2004 as C132104. DOI:10.1520/C1321-09.2The as-manufactured emittance of Interior Radiation Control Coating product,as determined on a typical substrate, should be stated

16、on the label (see 7.2.1).3Available from National Fire Protection Association, Batterymarch Park,Quincy, MA 02269.4Available from U.S. Consumer Product Safety Commission, Washington, DC20207.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United S

17、tates.IRCCS is used for the sole purpose of limiting heat transfer byradiation and is not specifically intended to reduce heat transferby convection or conduction.3.2.4 open air spacea vented building cavity (for ex-ample, a vented attic) or a large conditioned or unconditionedbuilding space.3.2.5 D

18、iscussionA large building space is defined as onewhose minimum dimension exceeds two feet.3.2.6 ownerthe person, partnership, corporation, agency,or other entity who owns the building in which the IRCCS isto be applied whether such ownership is by virtue of deed,contract, or any other instrument for

19、 acquiring legal title underthe laws of the state in which the building is located.4. Significance and Use4.1 This practice recognizes that effectiveness, safety, anddurability of an IRCCS depends not only on the quality of thematerials, but also on the proper installation.4.2 Improper installation

20、of an IRCCS will reduce itsthermal effectiveness, cause fire risks and other unsafe condi-tions, and promote deterioration of the structure in which it isinstalled. Specific hazards that can result from improperinstallation include: heat buildup in recessed lighting fixtures,deterioration of failure

21、 of electrical wiring components, anddeterioration of wood structures and paint failure due tomoisture accumulation.4.3 This practice provides recommendations for the instal-lation of IRCCS materials in a safe and effective manner.Actual conditions in existing buildings will vary greatly.4.4 This pr

22、actice presents requirements that are general innature and considered practical. They are not intended asspecific recommendations. Consult the manufacturer for rec-ommended application methods.5. Safety Precautions5.1 The applicator shall wear proper clothing and equipmentas recommended by the manuf

23、acturer and shall follow localcodes and safety regulations for building construction sites.(For example, hard hats, safety goggles, and respiratory pro-tection will be required, depending on site conditions.)5.2 Ventilation shall be provided to insure that mist andoverspray are immediately dispersed

24、 from the application area.If natural ventilation is not adequate, place OSHA approvedfans may be placed in windows or doors adjacent to theapplication area to improve ventilation.5.3 Manufacturers instructions shall be consulted for allapplicable handling and safety recommendations.6. Pre-Installat

25、ion Inspection and Preparation6.1 Inspections:6.1.1 Inspect the roof, walls, ceilings, and floors to identifyareas where previous or existing moisture problems havecaused paint peeling, warpage, stain, visible fungus growth,rotting, or other structural damage. Do not apply IRCCS insuch areas until t

26、he owner has been informed and has certifiedthese conditions have been corrected and their source(s)eliminated.6.1.2 In areas where the IRCCS is to be applied, compo-nents of the electrical system shall be in good condition. Ifthere is reason to believe the electrical system is faulty, do notapply t

27、he IRCCS in such areas until the owner has beeninformed and qualified inspection and repair have been per-formed.NOTE 1The CPSC Product Safety Fact Sheet No. 18 has identified thefollowing signs of potential electrical deficiencies: lights dimming, fusesblowing, circuit breakers tripping frequently,

28、 electrical sparks and glowingfrom receptacles, light flickering, and cover plates on switches and outletsthat are warm or hot to the touch. Useful safety information is alsocontained in the NFPA 54 and NFPA 211.6.1.3 In areas where an IRCCS is to be applied, theapplicator shall locate and plan the

29、application around venti-lation openings. The applicator shall not apply the IRCCS in away that will plug or otherwise obstruct existing ventilationopenings.6.2 Preparations:6.2.1 All electrical wiring at or near the IRCCS applicationsurfaces shall be protected to ensure that the IRCCS materialcanno

30、t contact the electrical wiring system.6.2.2 Where attic ventilation is compromised by the instal-lation of an IRCCS or the subsequent application of fibrousinsulation, vent baffles shall be installed at the soffits of theattic such that attic ventilation airflows are maintained inaccordance with ap

31、plicable building codes.6.2.3 All materials shall be mixed for at least 2 minimmediately before spraying. Manufacturers instructions shallbe consulted for type of mixing equipment and mixing methodsto be employed. If material is to be sprayed from a pressurepot, the pot shall be equipped with an air

32、 driven agitator.7. Installation Guidelines7.1 Material Handling:7.1.1 The IRCCS materials shall be applied, handled, andstored in accordance with manufacturers instructions.NOTE 1Apply IRCCS to cover the exposed roof deck area. Thelow-emittance surface of the IRCCS must face the interior of the att

33、ic.FIG. 1 Typical Residential UseNOTE 1Apply the IRCCS to cover the entire interior surface area. Thelow-emittance surface of the IRCCS must face the interior of the bldg.FIG. 2 Typical Industrial, Commercial, and Agricultural UseC1321 0927.1.2 The IRCCS materials shall not be applied in directconta

34、ct with corrosive building materials.7.2 Performance Considerations:7.2.1 The performance of the IRCCS depends on adherenceto manufacturers recommendations. Manufacturers installa-tion instructions and local building codes shall be followed.The manufacturer shall provide product sheet(s) that specif

35、ythe products intended use(s), application method(s), healthand safety considerations, and material properties to include:(1) the IRCCS surface emittance determined in accordancewith Test Method C1371;(2) the applied material water vaportransmission rate, in accordance with Test Methods E96/E96Mand;

36、 (3) the applied material surface burning characteristics inaccordance with Test Method E84.7.2.2 The performance of the IRCCS is dependent on themaintenance of an open airspace facing the low emittancesurface.7.2.3 The performance of the IRCCS are affected by foreignmaterials on the low emittance s

37、urface. After application,foreign materials shall be removed using manufacturers in-structions, taking care not to damage the IRCCS surface.7.2.3.1 Some IRCCS will provide a high resistance to watervapor transmission. An IRCCS shall not be applied so as tolead to moisture accumulation and deteriorat

38、ion in the struc-ture.7.2.4 All roof support structure directly connected to theroof deck (such as purlins, rafters, and top chord of trusses)shall be coated on any exposed surface.7.3 Post-installationThe applicator shall provide a signedand dated statement describing the IRCCS applicator, installe

39、din accordance with Practice C1321 and the area covered.8. Keywords8.1 low emittance; painthigh reflectance; painthightemperature; paintlow emittance; paintspray-applied; ra-diation; radiation control coating; radiation controlcoatinginteriorASTM International takes no position respecting the validi

40、ty of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subjec

41、t to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarte

42、rs. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard

43、is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1321 093

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1